Block Coefficient (Cb): Definition, Rules and Uses

The block coefficient Cb is displaced volume over L x B x T. How load line, IACS, IS Code and EEDI rules define and use it, with values and a worked example.

Contents18 sections

The block coefficient \( C_B \) is the displaced volume of a ship divided by the volume of the box of its length, breadth and draft. It measures how full the underwater hull is. A value of 1.0 describes a box. The Load Line Convention, the IACS structural rules, the 2008 IS Code and the EEDI guidelines all use \( C_B \). Each instrument states its own length and draft.

One hull therefore has several block coefficients, one for each rule basis. A freeboard, a wave bending moment, an EEDI correction and a squat estimate each take \( C_B \) on a different footing. The other hull-form coefficients and the dimension ratios are in the hull form coefficients hub. The worked numbers are for example ships, not real ships. Most use one example ship, and each other example states its own data.

Block coefficient defined

The block coefficient is the ratio of the moulded displaced volume \( \nabla \) to the product \( L \times B \times T \). It has no unit. The volume is the moulded volume, inside the shell plating, and the draft is the moulded draft at which the coefficient is taken.

Definition

Block coefficient

$$\textcolor{#2a78d6}{C_{B}} = \frac{\textcolor{#eb6834}{\nabla}}{L \times B \times \textcolor{#1baf7a}{T}}$$

where

\(C_{B}\)block coefficient
\(\nabla\)moulded displaced volume at draft Tm³
\(L\)length on the stated basism
\(B\)moulded breadthm
\(T\)moulded draft at which the coefficient is takenm

Figure 1 shows the idea for the example ship used on this page and in the freeboard and reserve buoyancy article. The ship has a freeboard length of 150 m, a breadth of 25 m and a moulded depth of 13.5 m. The example ship has a block coefficient of 0.80 at every draft used here, a simplification that a real hull does not follow.

Figure 1 draws it at its summer draft of 10.33 m beside a finer hull of \( C_B = 0.62 \) in the same box. That value is the low end of the MAN range for a liner container ship, given in the table of typical values below.

Full form,CB = 0.80Plan: waterplane in L × BBProfile: hull in L × TTLMidship section∇ = 30,990 m³Fine form,CB = 0.62Plan: waterplane in L × BBProfile: hull in L × TTLMidship section∇ = 24,017 m³Same box: L 150 m, B 25 m, T 10.33 mBox volume L × B × T = 38,738 m³L lengthB breadthT draft
Full form,CB= 0.80Plan: waterplane in L × BBProfile: hull in L × TTLMidship section∇ = 30,990 m³Fine form,CB= 0.62Plan: waterplane in L × BBProfile: hull in L × TTLMidship section∇ = 24,017 m³Same box: L 150 m, B 25 m, T 10.33 mBox volume L × B × T = 38,738 m³L lengthB breadthT draft
Figure 1. Two hulls in one box of length L, breadth B and draft T, in plan, profile and midship section. The finer hull fills less of the dashed box, so it displaces less at the same dimensions. Breadth and draft are enlarged in plan and profile. Both hulls are examples.

A box-shaped barge has \( C_B = 1.0 \), because the hull fills its own box. A real ship has fine ends and a rounded bilge, so the value is less than 1.0. The 2008 IS Code treats a pontoon as a hull with a block coefficient of 0.9 or greater (Introduction, 2.16). A barge hull is that close to a box.

The block coefficient is the product of two other coefficients. The prismatic coefficient \( C_P \) describes how the volume is spread along the length. The midship section coefficient \( C_M \) describes how full the midship section is.

Hydrostatic relation

Block, prismatic and midship section coefficients

$$\textcolor{#2a78d6}{C_{B}} = \textcolor{#eb6834}{C_{P}} \times \textcolor{#1baf7a}{C_{M}}$$

where

\(C_{B}\)block coefficient
\(C_{P}\)prismatic coefficient, displaced volume over L times midship area
\(C_{M}\)midship section coefficient, midship area over B times T

For the example ship, \( C_M = 0.99 \) and \( C_P = 0.808 \), so \( C_B = 0.80 \). The waterplane area coefficient \( C_{WP} \) is a third companion coefficient, used in the bow height rule below. A naval architect reads \( C_B \) with these companions, because two hulls with one \( C_B \) can have different ends. MAN Energy Solutions puts the midship section coefficient of merchant ships at about 0.95 to 0.99. The same paper gives a rough relation \( C_{WL} \approx C_B + 0.10 \) for the waterplane, with a larger gap on fast, fine ships (5510-0004-04, pp. 7 to 8).

Length, breadth and draft in the four rule definitions of the block coefficient

Four instruments define the block coefficient, and each takes the length, the breadth and the draft at a different waterline. A value quoted without its basis cannot be checked against a rule. Figure 2 shows the three drafts on the example ship.

deck at side, moulded depth D = 13.5 mbaseline (top of keel)d1 = 0.85D = 11.475 mICLL Annex I Reg 3(7): load line CBTs = scantling draft (example 10.6 m)IACS UR S2 Rev.2 and CSR: strength CBds = 10.33 m, summer load line draftMEPC.364(79): EEDI CBOne hull, three drafts in the rules, three values of CB
deck at side, moulded depth D = 13.5 mbaseline (top of keel)d1 = 0.85D = 11.475 mICLL Annex I Reg 3(7): load line CBTs = scantling draft (example 10.6 m)IACS UR S2 Rev.2 and CSR: strength CBds = 10.33 m, summer load line draftMEPC.364(79): EEDI CBOne hull, three drafts in the rules, threevalues of CB
Figure 2. The example ship has a moulded depth of 13.5 m. The Load Line Convention takes the block coefficient at 11.475 m, IACS UR S2 and CSR at the scantling draft, and the EEDI guidelines at the summer draft of 10.33 m. On a real hull each draft gives a different block coefficient; the example keeps 0.80 for simplicity. The scantling draft of 10.6 m is an example value.

Load Line Convention, Annex I Reg 3(7)

Annex I Regulation 3(7) of the Load Line Convention takes the block coefficient at the draft \( d_1 \), which is 85% of the least moulded depth. The text is in the 1988 Protocol as revised by resolution MSC.143(77), in force 1 January 2005. The volume is the moulded displacement volume, excluding appendages, and a multi-hull ship uses its full breadth (Reg 3(7)(b)).

LL Annex I Reg 3(1) and 3(7)

Load line block coefficient

$$\textcolor{#2a78d6}{C_{B}} = \frac{\nabla}{L \times B \times \textcolor{#1baf7a}{d_{1}}}, \qquad \textcolor{#1baf7a}{d_{1}} = 0.85\,\textcolor{#eb6834}{D}$$

where

\(C_{B}\)block coefficient for freeboard
\(\nabla\)moulded displacement volume at d1, excluding appendagesm³
\(L\)freeboard length, Reg 3(1), on the waterline at 0.85Dm
\(B\)moulded breadth, Reg 3(2)m
\(d_{1}\)85% of the least moulded depthm
\(D\)least moulded depthm

The length is the freeboard length of Reg 3(1)(a). The freeboard length is 96% of the total length on the waterline at 85% of the least moulded depth. Where the length from the fore side of the stem to the rudder stock axis on that waterline is greater, that length is used. This length is not the length between perpendiculars of the design office, although the two are often close. For the example ship, \( d_1 = 0.85 \times 13.5 = 11.475 \) m, which is deeper than its summer draft of 10.33 m.

IACS UR S2 Rev.2, the classification basis

IACS UR S2 Rev.2 (June 2019) takes the block coefficient at the scantling draft \( T_s \), on the rule length. IACS members applied Rev.2 from 1 July 2020. The rule length is measured on the waterline at the scantling draft. The length runs from the fore side of the stem to the after side of the rudder post. Where there is no rudder post, it ends at the center of the rudder stock.

IACS UR S2 Rev.2 (June 2019), S2.2

Classification block coefficient

$$\textcolor{#2a78d6}{C_{b}} = \frac{\nabla_{\mathrm{s}}}{L \times B \times \textcolor{#1baf7a}{T_{\mathrm{s}}}}$$

where

\(C_{b}\)block coefficient for strength rules
\(\nabla_{\mathrm{s}}\)moulded displacement at the scantling draftm³
\(L\)rule length on the waterline at the scantling draft, S2.1m
\(B\)greatest moulded breadth amidships at the scantling draftm
\(T_{\mathrm{s}}\)scantling draft, not less than the draft at the assigned freeboardm

Under S2.1, the rule length is between 96% and 97% of the extreme length on the waterline at the scantling draft. The scantling draft is the draft at which the strength requirements are met. S2.2 states that it “is not to be less than that corresponding to the assigned freeboard”. A class document that quotes C_b without its draft cannot be checked against Rev.2.

UR S2 does not apply to bulk carriers and oil tankers built to the IACS Common Structural Rules (S2.0). Classification societies use the UR S2 value in the hull girder rules of UR S11, described below.

IACS Common Structural Rules for bulk carriers and oil tankers

The Common Structural Rules define the block coefficient from the mass displacement in tonnes at the scantling draft, divided by 1.025. The definition is in Part 1, Chapter 1, Section 4, [3.1.8] of the January 2024 text. The factor 1.025 converts the mass in sea water to a volume.

CSR BC and OT Pt 1 Ch 1 Sec 4 [3.1.8]

CSR block coefficient from mass displacement

$$\textcolor{#2a78d6}{C_{B}} = \frac{\textcolor{#eb6834}{\Delta}}{1.025 \times L \times B \times \textcolor{#1baf7a}{T_{SC}}}$$

where

\(C_{B}\)block coefficient at the scantling draft
\(\Delta\)moulded displacement at the scantling draftt
\(L\)rule length on the waterline at the scantling draftm
\(B\)moulded breadthm
\(T_{SC}\)scantling draftm

The CSR value and the UR S2 value use the same draft and the same kind of rule length. The difference is the starting quantity: CSR starts from mass in tonnes and UR S2 from volume in cubic metres.

EEDI calculation guidelines, MEPC.364(79)

The 2022 EEDI calculation guidelines, resolution MEPC.364(79), take the block coefficient at the summer load line draft \( d_s \). The length \( L_{pp} \) in paragraph 2.2.13 has the same wording as the load line length of Reg 3(1). The breadth \( B_s \) is the greatest moulded breadth at or below \( d_s \) (2.2.16), and the volume excludes appendages (2.2.17).

MEPC.364(79), paras 2.2.13 to 2.2.17

EEDI block coefficient

$$\textcolor{#2a78d6}{C_{b}} = \frac{\nabla}{L_{pp} \times B_{s} \times \textcolor{#1baf7a}{d_{s}}}$$

where

\(C_{b}\)block coefficient for the EEDI factors
\(\nabla\)moulded displacement volume at ds, excluding appendagesm³
\(L_{pp}\)length with the wording of LL Annex I Reg 3(1)m
\(B_{s}\)greatest moulded breadth at or below dsm
\(d_{s}\)summer load line draftm

The EEDI value uses the load line length but the summer draft, not 0.85D. For the example ship the two drafts differ by 1.145 m. The EEDI value is the one used in the EEDI correction factors described below.

Design-office practice: LBP and LWL

Outside the rules, a design office quotes the block coefficient on the length between perpendiculars or on the waterline length, at the design draft. Resistance methods often use the waterline length. The length is in the denominator, so for the same volume a longer length gives a lower value. MAN Energy Solutions notes that the length between perpendiculars is normally slightly shorter than the waterline length. A block coefficient on that length is therefore slightly larger (5510-0004-04, p. 7).

The ship length definitions article compares these lengths in one place. Before two ships are compared, both values are put on one length and one draft.

How the block coefficient changes with draft

The block coefficient of one hull changes with draft, so every value belongs to one waterline. Most hulls have flared sections and finer ends at the bottom, so \( C_B \) usually rises as the draft increases. The hydrostatic tables in the stability-booklet give \( C_B \) against draft for the actual hull.

A ship in ballast floats at a lower draft than when laden, so its block coefficient in ballast is lower. Trim changes the immersed volume distribution but not the definition: the rules take \( C_B \) at a level waterline on the stated draft. A value from the loading computer at the current trim is a different quantity.

The appendages, such as the rudder, the shaft bossings and the bilge keels, are outside the moulded volume in all four rule definitions. The shell plating is outside it too. These are excluded from \( C_B \) but included in the displacement used in a draft survey, which works from the actual displacement in tonnes.

Calculating the block coefficient from offsets

A naval architect calculates the block coefficient by integrating the immersed station areas along the length and dividing by \( L \times B \times T \). The station areas come from the offsets in the lines plan. Each station area is the integral of the half-breadths from the keel to the waterline, times two.

The plot of station area against length is the sectional area curve. Figure 3 shows it for the example ship, with each station area divided by \( B \times T \).

0.00.20.40.60.81.0a(x) / (B × T)Position along L, from aft perpendicular (stations 0 to 10)012345678910midship section aM / (B × T) = CM = 0.99area under the curve = CB = 0.80dashed box = 1.0
Figure 3. The sectional area curve of the example ship: each station area divided by B × T, from the aft perpendicular to the forward perpendicular. The area under the curve, as a fraction of the dashed box of height 1.0, is the block coefficient. Simpson's first rule over the 11 dots gives 0.8003. The flat top is the parallel middle body, at a midship section coefficient of 0.99.

The area under that curve, divided by the area of the dashed box, is the block coefficient. Simpson’s first rule gives it from a table of stations at equal spacing.

Simpson's first rule

Block coefficient from station areas

$$\textcolor{#2a78d6}{C_{B}} = \frac{1}{3n}\sum_{i=0}^{n} \textcolor{#eb6834}{k_{i}}\,\textcolor{#1baf7a}{\frac{a_{i}}{B\,T}}$$

where

\(C_{B}\)block coefficient
\(n\)number of equal intervals, an even number
\(k_{i}\)Simpson multiplier: 1, 4, 2, 4, ..., 4, 1
\(a_{i}\)immersed area of station i at draft Tm²
\(B,\ T\)breadth and draft of the boxm

The steps for the example ship, with 10 equal intervals and 11 stations, are:

  1. Read the immersed area ratio \( a_i / (B\,T) \) at each station from the hydrostatic offsets.
  2. Multiply each ratio by its Simpson multiplier \( k_i \).
  3. Add the 11 products.
  4. Divide the sum by \( 3n = 30 \).
Station012345678910
\( a_i / (B\,T) \)0.0000.4850.8080.9700.9900.9900.9900.9900.9530.6970.000
\( k_i \)14242424241
Product0.0001.9401.6163.8801.9803.9601.9803.9601.9062.7880.000

The products add to 24.01, so \( C_B = 24.01 / 30 = 0.8003 \). A fine integration of the same example curve also gives 0.8003, so 11 stations give a good result for a smooth curve. A real hull has a bulb and a transom, so its ends are less smooth. A design office then uses more stations near the ends, or a hydrostatic program that integrates the hull surface.

The volume from this integration also gives the displacement: \( \Delta = 1.025 \times \nabla \) in sea water. The approved hydrostatic tables, not a hand integration, give the values used for statutory purposes.

Typical block coefficient values and the IMO reference table

Table 3 of the EEDI guidelines, MEPC.364(79), gives IMO reference block coefficients for three cargo ship types. The guidelines call them average block coefficients and use them to correct the EEDI of ice-classed ships. They are reference values for a regulation, not a design survey.

Ship typeBelow 10,000 DWT10,000 to 25,000 DWT25,000 to 55,000 DWT55,000 to 75,000 DWTAbove 75,000 DWT
Bulk carrier0.780.800.820.860.86
Tanker0.780.780.800.830.83
General cargo ship0.800.800.800.800.80

The table gives one value for general cargo ships at all sizes. The values rise with deadweight for bulk carriers and oil tankers, so the larger ships in the IMO data are fuller. The table is on the EEDI basis of paragraph 2.2.17: summer load line draft and the load line length.

MAN Energy Solutions gives wider ranges by ship type in Table 1.01 of Basic Principles of Ship Propulsion, document 5510-0004-04 (October 2018). The paper calls the table “only a rough outline” and does not state the length basis. MAN defines its own \( C_B \) on the waterline length.

Ship type\( C_B \)Service speed (kn)
Crude oil carrier0.78 to 0.8313 to 17
Product tanker0.75 to 0.8013 to 16
Chemical tanker0.70 to 0.7815 to 18
Gas tanker or LNG carrier0.65 to 0.7516 to 20
Ore carrier0.80 to 0.8514 to 15
Bulk carrier, regular0.75 to 0.8512 to 15
Container ship, liner0.62 to 0.7220 to 23
Container ship, feeder0.60 to 0.7018 to 21
General cargo ship0.70 to 0.8514 to 20
Ro-ro cargo ship0.55 to 0.7018 to 23
Ro-pax ship0.50 to 0.7018 to 23
Cruise ship0.60 to 0.7020 to 23
Ferry0.50 to 0.7016 to 23

The table shows what MAN calls “a strong correlation between ship speed and block coefficient”. The slower types, tankers and bulk carriers, have the fullest hulls. The same paper notes that container ships with larger block coefficients “are seen now, as the speed of such ships has dropped”.

Block coefficient in load line freeboard

The Load Line Convention increases the freeboard of a ship whose block coefficient exceeds 0.68, and it gives no reduction below 0.68. The rule is Annex I Regulation 30, in the text of the 1988 Protocol as revised by MSC.143(77). The coefficient is the Reg 3(7) value at 0.85D.

LL Annex I Reg 30

Block coefficient correction to freeboard

$$\textcolor{#1baf7a}{F} = \textcolor{#eb6834}{F_{0}} \times \frac{\textcolor{#2a78d6}{C_{B}} + 0.68}{1.36} \qquad \text{where } 0.68 < \textcolor{#2a78d6}{C_{B}} \leq 1.0$$

where

\(F\)freeboard after the correctionmm
\(F_{0}\)tabular freeboard, as modified by Regs 27(8), 27(10) and 29mm
\(C_{B}\)block coefficient by Reg 3(7), not taken greater than 1.0

The tabular freeboard is first taken from Reg 28 and modified by Regs 27(8), 27(10) and 29. Reg 30 then multiplies it by the factor. The block coefficient is not taken greater than 1.0, so the factor cannot exceed 1.235. Figure 4 shows the factor against \( C_B \) for the example ship.

0.951.001.051.101.151.201.250.50.60.70.80.91.0Block coefficient CB at d1 = 0.85DReg 30 factorno correctionat 0.68 or less0.68(CB + 0.68) / 1.36
Figure 4. The Reg 30 factor stays at 1.0 up to the threshold and rises linearly above it, so a fuller hull gets more freeboard. The corrected freeboard of the example ship follows from the tabular value multiplied by the factor.Move the block coefficient. Up to 0.68 the factor stays at 1.0 and the freeboard does not change. Above 0.68 each 0.01 of block coefficient adds about 17 mm to the example ship's freeboard, up to the cap at 1.0.

For the example ship the Type B tabular freeboard at 150 m is 2,315 mm (Reg 28, table 28.2). The factor at \( C_B = 0.80 \) is (0.80 + 0.68)/1.36 = 1.0882. The corrected value is 2,519 mm, so the correction adds 204 mm. The freeboard and reserve buoyancy article takes the example from the tables to a summer freeboard of 3,170 mm. The freeboard calculation article covers the full assignment chain.

Annex I states no reason for the 0.68 threshold or for the 0.85D draft. The regulation fixes the numbers and does not explain them.

Minimum bow height, Reg 39

The minimum bow height formula of Annex I Regulation 39(1) also contains the Reg 3(7) block coefficient. The formula has its present form from resolution MSC.223(82), in force 1 July 2008. A fuller hull, other terms equal, needs a higher bow.

LL Annex I Reg 39(1), as amended by MSC.223(82)

Minimum bow height

$$\textcolor{#1baf7a}{F_{b}} = \left(6075\tfrac{L}{100} - 1875\left(\tfrac{L}{100}\right)^{2} + 200\left(\tfrac{L}{100}\right)^{3}\right)\left(2.08 + 0.609\,\textcolor{#2a78d6}{C_{B}} - 1.603\,\textcolor{#eb6834}{C_{wf}} - 0.0129\,\tfrac{L}{d_{1}}\right)$$

where

\(F_{b}\)minimum bow heightmm
\(L\)freeboard length, Reg 3(1)m
\(C_{B}\)block coefficient by Reg 3(7)
\(C_{wf}\)waterplane coefficient forward of L/2 at d1
\(d_{1}\)draft at 85% of the least moulded depthm

The \( C_B \) term has a positive coefficient of 0.609, and the forward waterplane coefficient \( C_{wf} \) has a negative coefficient of 1.603. For the example ship, Reg 39(1) gives a required bow height of 6,216 mm, which the forecastle provides. The worked bow height is in the freeboard and reserve buoyancy article.

Block coefficient in the IS Code weather criterion

The 2008 IS Code uses the block coefficient in the severe wind and rolling criterion, through the factor \( X_2 \) in the angle of roll \( \varphi_1 \). The criterion is Part A, 2.3, of the 2008 IS Code adopted by resolution MSC.267(85). Part A became mandatory on 1 July 2010 through amendments to SOLAS and to the 1988 Load Line Protocol.

2008 IS Code, Part A, 2.3.4

Weather criterion angle of roll

$$\textcolor{#1baf7a}{\varphi_{1}} = 109\,k\,X_{1}\,\textcolor{#2a78d6}{X_{2}}\,\sqrt{r\,s}$$

where

\(\varphi_{1}\)angle of roll to windward due to wave action°
\(k\)factor for bilge keels, Table 2.3.4-4
\(X_{1}\)factor for B/d, Table 2.3.4-1
\(X_{2}\)factor for the block coefficient, Table 2.3.4-2
\(r\)0.73 + 0.6 OG/d, where OG is the height of G above the waterline
\(s\)factor for the roll period, Table 2.3.4-3

Table 2.3.4-2 gives \( X_2 \) against \( C_B \), with linear interpolation between the points. Figure 5 plots the table.

0.700.750.800.850.900.951.001.050.400.450.500.550.600.650.700.750.800.85Block coefficient CBFactor X20.75 at 0.45 or less1.00 at 0.70 or moreTable 2.3.4-2 points; straight lines between them
Figure 5. Factor X2 of the 2008 IS Code weather criterion, Part A, Table 2.3.4-2. X2 is 0.75 for a block coefficient of 0.45 or less and 1.00 for 0.70 or more, with linear interpolation between the table points. A fuller hull gets a larger computed angle of roll, other factors equal.
\( C_B \)0.45 or less0.500.550.600.650.70 or more
\( X_2 \)0.750.820.890.950.971.00

A ship with \( C_B = 0.80 \) takes \( X_2 = 1.00 \), the top value. A ship with \( C_B = 0.58 \) takes 0.926 by interpolation between 0.89 and 0.95. A fine hull at 0.45 gets an angle of roll 25% lower than a full hull with the same other factors.

The Code defines \( C_B \) in 2.3.4 only as “block coefficient (-)” and does not name its length basis. The same list of symbols gives the waterline length \( L_{WL} \) and the mean moulded draft \( d \). The tables are based on ships with \( B/d \) smaller than 3.5, \( (KG/d - 1) \) between -0.3 and 0.5, and a roll period smaller than 20 s (2.3.5). Outside those limits the angle of roll can come from model tests under MSC.1/Circ.1200, if the Administration accepts them.

The result feeds the severe wind and rolling criterion of Part A 2.3, which compares areas under the righting arm curve and the wind heeling lever. The general intact stability criteria of Part A, 2.2, contain no block coefficient.

Part B, 2.3, of the Code is a recommended alternative criterion for container ships longer than 100 m. Its form factor contains the ratio of \( C_B \) to the waterplane coefficient. Part B is recommendatory, so the factor applies only where the Administration applies that section.

Block coefficient in hull girder loads

IACS UR S11 Rev.10 (December 2020) makes the wave bending moment amidships proportional to \( C_b \) in hogging and to \( C_b + 0.7 \) in sagging. The block coefficient is the UR S2 value, “but not to be taken less than 0.6”. The Rev.10 changes apply to ships contracted for construction on or after 1 January 2022.

IACS UR S11 Rev.10 (Dec 2020), S11.2.2.1

Wave bending moment amidships

$$\textcolor{#1baf7a}{M_{w,\mathrm{hog}}} = +190\,M\,C\,L^{2}B\,\textcolor{#2a78d6}{C_{b}} \times 10^{-3}$$
$$\textcolor{#eb6834}{M_{w,\mathrm{sag}}} = -110\,M\,C\,L^{2}B\,(\textcolor{#2a78d6}{C_{b}} + 0.7) \times 10^{-3}$$

where

\(M_{w,\mathrm{hog}}\)wave bending moment, positive (hogging)kNm
\(M_{w,\mathrm{sag}}\)wave bending moment, negative (sagging)kNm
\(M\)distribution factor along the length, 1.0 amidships
\(C\)wave coefficient, 10.75 - ((300 - L)/100)^1.5 for L from 90 to 300 m
\(L,\ B\)rule length and greatest moulded breadth, UR S2m
\(C_{b}\)block coefficient by UR S2, not taken less than 0.6

UR S11 applies to steel ships of 90 m and above in unrestricted service. UR S11 does not apply to bulk carriers and oil tankers built to the Common Structural Rules or to container ships, which use UR S11A (S11.1). The hull strength and longitudinal bending article covers the still water moments and the section modulus.

Figure 6 shows the two moments against \( C_b \) for an example hull of rule length 150 m and breadth 25 m. With \( M = 1.0 \) amidships, the wave coefficient is \( C = 10.75 - (150/100)^{1.5} = 8.913 \).

0200,000400,000600,000800,0001,000,0000.450.550.650.750.85Block coefficient CBWave bending moment (kNm)floor 0.6sagging, CB + 0.7hogging, CB
Figure 6. Wave bending moments amidships for the example hull. Hogging grows with the block coefficient and sagging with the block coefficient plus 0.7, so sagging is larger. Both lines are flat below the floor, where the formula holds the coefficient constant.Move the block coefficient. Each 0.01 of block coefficient above the floor adds about 9,500 kNm to the hogging moment and 5,500 kNm to the sagging moment. Below 0.6 the formula keeps 0.6, so the moments stop falling.

At \( C_b = 0.80 \) the hogging moment is 762,051 kNm and the sagging moment is 827,227 kNm. The sagging moment is larger, because 110 × 1.50 = 165 is greater than 190 × 0.80 = 152. Below \( C_b = 0.6 \) both moments stay at their floor values.

The floor matters for fine hulls. A hull with an actual \( C_b \) of 0.55 is calculated at 0.6, so the hogging moment is 9.1% higher than the actual value would give. The sagging moment is 4.0% higher, because 1.30 is 4.0% more than 1.25.

The floor of 0.6 is in the formula. S11.1 also lists a block coefficient below 0.6 as a case for “special additional considerations” by the society, with unusual dimension ratios and large flare. The same \( C_b + 0.7 \) term is in the wave shear force. The minimum midship moment of inertia is \( I_{min} = 3\,C\,L^3 B (C_b + 0.7) \) in cm to the fourth power (S11.3.1.2).

Common Structural Rules

The Common Structural Rules use the block coefficient in the vertical wave bending moment for bulk carriers and oil tankers. Part 1, Chapter 4, Section 4 sets no 0.6 floor. The formulas are in [3.1.1] of that section, in the January 2024 text. Hogging is \( 0.19\,f_{nl\text{-}vh}\,f_m\,f_p\,C_w\,L^2 B\,C_B \).

Sagging has the same form with \( f_{nl\text{-}vs} = 0.58\,(C_B + 0.7)/C_B \) for the strength assessment. The product 0.19 × 0.58 = 0.1102 gives the same sagging form as UR S11, with the added factors \( f_m \) and \( f_p \). The CSR hogging and sagging moments therefore depend on hull fullness in the same direction as UR S11.

Block coefficient in EEDI, EEXI and minimum propulsion power

The EEDI calculation guidelines, MEPC.364(79), use the block coefficient in two factors only: \( f_j \) for general cargo ships and \( f_{iCb} \) for ice-classed ships. Neither the main EEDI formula nor the reference speed contains it. The attained EEDI is Regulation 22 of MARPOL Annex VI as revised by MEPC.328(76), in force 1 November 2022.

For a bulk carrier or a tanker, the capacity in the attained EEDI is the deadweight at the summer load draft (2.2.3.1 and 2.2.4). The main engine power is 75% of the rated installed power, and the speed is the reference speed \( V_{ref} \). The guidelines take that speed from the speed-power curve, not from a resistance formula in \( C_B \).

Ice-class capacity correction

For an ice-classed bulk carrier, tanker or general cargo ship, MEPC.364(79) paragraph 2.2.11.1 multiplies the ice-class capacity factor by \( f_{iCb} \). The factor compares the ship’s block coefficient with the Table 3 reference for its type and size.

MEPC.364(79), para 2.2.11.1

Ice-class capacity correction for hull fullness

$$\textcolor{#1baf7a}{f_{iCb}} = \frac{\textcolor{#eb6834}{C_{b,\mathrm{ref}}}}{\textcolor{#2a78d6}{C_{b}}} \geq 1.0$$

where

\(f_{iCb}\)capacity correction for improved ice-going capability
\(C_{b,\mathrm{ref}}\)average block coefficient for the ship type and size, Table 3
\(C_{b}\)block coefficient of the ship, para 2.2.17 basis

The factor is not less than 1.0, so a ship finer than the reference gets a capacity credit and a fuller ship gets none. Take a 60,000 DWT ice-classed bulk carrier as a second example. With \( C_b = 0.80 \) it has \( f_{iCb} = 0.86 / 0.80 = 1.075 \). The same ship at \( C_b = 0.88 \) gives 0.977, which is taken as 1.0. For other ship types \( f_{iCb} = 1.0 \).

The factor multiplies the ice-class factor of Table 2 in the same guidelines. For ice class IA that factor is \( 1.0099 + 95.1/DWT \), or 1.0115 at 60,000 DWT. The product for the 60,000 DWT example at \( C_b = 0.80 \) is 1.0115 × 1.075 = 1.087. The capacity term of the attained EEDI rises by 8.7%.

General cargo ship factor

For a general cargo ship, MEPC.364(79) paragraph 2.2.8.4 gives the correction factor \( f_j \) from the block coefficient and a Froude number based on volume. The factor is capped at 1.0, and the Froude number is capped at 0.6.

MEPC.364(79), para 2.2.8.4

General cargo ship correction factor

$$\textcolor{#1baf7a}{f_{j}} = \frac{0.174}{\textcolor{#eb6834}{F_{n\nabla}}^{2.3} \times \textcolor{#2a78d6}{C_{b}}^{0.3}} \leq 1.0$$
$$\textcolor{#eb6834}{F_{n\nabla}} = \frac{0.5144\,V_{ref}}{\sqrt{g\,\nabla^{1/3}}} \leq 0.6$$

where

\(f_{j}\)ship-specific design correction factor, general cargo ships
\(F_{n\nabla}\)Froude number based on displacement volume, capped at 0.6
\(C_{b}\)block coefficient at the summer load line draft
\(V_{ref}\)reference speedkn
\(g\)gravitational accelerationm/s²
\(\nabla\)moulded displacement volume at dsm³

A slow general cargo ship gets the cap of 1.0. Take an example ship with \( \nabla = 20{,}000 \) m³ and \( C_b = 0.75 \):

  1. At \( V_{ref} = 14 \) knots, \( F_{n\nabla} = 7.20 / \sqrt{9.81 \times 27.14} = 0.441 \), so \( f_j = 1.245 \), which is taken as 1.0.
  2. At \( V_{ref} = 18 \) knots, \( F_{n\nabla} = 0.567 \), so \( f_j = 0.174 / (0.2716 \times 0.9173) = 0.698 \).

The faster ship gets the credit. At the same speed, a fuller hull gets a slightly larger credit through the \( C_b^{0.3} \) term. Other ship types take \( f_j = 1.0 \) unless their own subparagraph applies (2.2.8.5).

EEXI and minimum propulsion power

The EEXI calculation guidelines, MEPC.350(78), contain no block coefficient term of their own. They apply the EEDI guideline parameters “unless expressly provided otherwise”, so \( f_j \) and \( f_{iCb} \) reach the EEXI by that reference. MEPC.350(78) names the EEDI guidelines as MEPC.308(73), as amended, which MEPC.364(79) has since superseded. The EEXI reference speed approximation contains no \( C_B \).

The minimum propulsion power check of Regulation 24.5 follows MEPC.1/Circ.850/Rev.3, dated 7 July 2021. The circular applies to ships subject to Regulation 24 of 20,000 DWT and above. The Level 1 line is \( a \times DWT + b \), with no block coefficient. The Level 2 simplified wave resistance uses breadth, draft and length, also without \( C_B \). The block coefficient appears only in the optional semi-empirical method for added resistance in waves, in the appendix to Appendix 2.

The operational CII of Regulation 28 is calculated from fuel consumed, capacity and distance sailed. The CII formula contains no block coefficient.

Block coefficient in resistance, powering and propulsion

A fuller hull suits a slow ship and a finer hull suits a fast ship, because wave-making resistance grows with the Froude number. MAN Energy Solutions states that friction is “practically the only influencing parameter” below a Froude number of 0.15. Wave making increases above about 0.16 to 0.17 (5510-0004-04, p. 13).

The Froude number is \( F_n = V / \sqrt{g\,L_{WL}} \), with \( V \) in m/s. The example ship at 14 knots on 150 m has \( F_n = 0.188 \). MAN Table 1.02 gives 0.16 for a 200 m ship at 14 knots and 0.23 for a 300 m ship at 24 knots.

Figure 1.05 of the MAN paper, taken from Harvald (1983), marks bulk carriers at Froude numbers of about 0.15 to 0.18. In that band friction dominates and a full hull costs little in wave making. MAN states that fast ships “demand small block coefficients”, while slower ships “are most effective with a higher block coefficient”. The ship resistance and powering article covers the resistance components and the Froude number in full.

First estimate from the service speed

Barrass gives a first estimate of the fully loaded block coefficient from the service speed and the length between perpendiculars. The relation is in Chapter 1 of Ship Design and Performance for Masters and Mates (Elsevier, 2004), as an evolution of Alexander’s formula.

Barrass (2004), Ship Design and Performance, Ch. 1

Block coefficient from service speed

$$\textcolor{#2a78d6}{C_{B}} = 1 - m\,\frac{\textcolor{#eb6834}{V}}{\sqrt{\textcolor{#1baf7a}{L}}}, \qquad \textcolor{#2a78d6}{C_{B}} = 1.20 - 0.39\,\frac{\textcolor{#eb6834}{V}}{\sqrt{\textcolor{#1baf7a}{L}}}$$

where

\(C_{B}\)block coefficient, fully loaded
\(m\)slope for the ship type, from 0.182 for VLCCs to 0.265 for container ships
\(V\)service speedkn
\(L\)length between perpendicularsm

The slope \( m \) depends on the ship type. Barrass gives these slopes from Alexander’s research:

  • VLCCs of 50,000 to 200,000 t deadweight: 0.182
  • oil tankers of 25,000 to 50,000 t deadweight: 0.195
  • general cargo ships: 0.234
  • passenger liners: 0.254
  • container ships: 0.265

A larger slope makes the block coefficient fall faster with speed. The global form with 1.20 and 0.39 covers all ship types, and his worked example gives 0.700 for a 124 m ship at 14.25 knots.

Figure 7 shows the global relation for the example length of 150 m. At 14 knots the relation gives a block coefficient of 0.754.

0.30.40.50.60.70.80.91.0101214161820222426Service speed V (kn)Block coefficient CBCB = 1.20 − 0.39 V/√L
Figure 7. The Barrass global relation gives a first estimate of the fully loaded block coefficient from the service speed and the length. A faster design gets a finer hull. The example length is 150 m.Move the speed. Each knot lowers the indicated block coefficient by about 0.032 for the 150 m example. The relation is a first estimate for preliminary design, not a design value.

These relations are preliminary design estimates. A hull form design then refines the value with the Holtrop-Mennen method, model tests or CFD.

Wetted surface

The block coefficient enters the frictional resistance through the wetted surface area. MAN gives Mumford’s formula as a rule of thumb “within 15% accuracy” (5510-0004-04, p. 11).

MAN Energy Solutions 5510-0004-04 (2018), p. 11

Mumford wetted surface estimate

$$\textcolor{#1baf7a}{A_{S}} = 1.025 \times L_{pp} \times (\textcolor{#2a78d6}{C_{B}} \times B + 1.7 \times \textcolor{#eb6834}{T})$$

where

\(A_{S}\)wetted surface area of the hullm²
\(L_{pp}\)length between perpendicularsm
\(C_{B}\)block coefficient
\(B\)breadthm
\(T\)draftm

For the example ship at 10.33 m draft, \( A_S = 1.025 \times 150 \times (0.80 \times 25 + 1.7 \times 10.33) = 5{,}775 \) m². At fixed dimensions, a fuller hull has a larger bottom term and so a larger wetted surface. The frictional resistance is proportional to that area.

Wake fraction and thrust deduction

The wake fraction at the propeller rises with the block coefficient. MAN states that “the larger the block coefficient, the larger the wake fraction coefficient”. MAN gives first estimates of the wake and the thrust deduction, and cites Carlton, Marine Propellers and Propulsion, 3rd edition (2012), for the wake estimate.

MAN Energy Solutions 5510-0004-04 (2018), p. 19

First estimates of wake and thrust deduction

$$\textcolor{#eb6834}{w} = 0.5\,\textcolor{#2a78d6}{C_{B}} - 0.05, \qquad \textcolor{#1baf7a}{t} = 0.27\,\textcolor{#2a78d6}{C_{B}}$$
$$\eta_{H} = \frac{1 - \textcolor{#1baf7a}{t}}{1 - \textcolor{#eb6834}{w}}$$

where

\(w\)wake fraction coefficient
\(t\)thrust deduction fraction
\(C_{B}\)block coefficient
\(\eta_{H}\)hull efficiency

For \( C_B = 0.80 \) the estimates give \( w = 0.35 \) and \( t = 0.22 \), the same values as the worked example in the MAN paper (p. 54). The hull efficiency is then 0.784/0.65 = 1.21. MAN Table 2.02 gives typical ranges for single-screw ships: 0.20 to 0.45 for \( w \) and 0.10 to 0.30 for \( t \). The hull efficiency range is 1.1 to 1.3.

MAN adds that a large ratio of propeller diameter to draft reduces the wake fraction. The estimates are for single-screw ships, and the paper gives no twin-screw form in \( C_B \). The marine propeller article covers propeller design in that wake.

Block coefficient and squat

Squat increases with the block coefficient, and the block coefficient decides whether the ship squats more by the bow or by the stern. UK MCA MGN 199 (M) Amendment 1, paragraph 3.1, defines squat as dynamic sinkage and trim. The ship’s motion through the water causes it.

Barrass’s simplified maximum squat formula contains \( C_B \) and the speed squared. Serban and Panaitescu (2016), in the “Mircea cel Batran” Naval Academy Scientific Bulletin, Vol. XIX, Issue 1, give it with its limits.

Barrass, in Serban and Panaitescu (2016)

Maximum squat, simplified form

$$\textcolor{#1baf7a}{S_{max}} = \frac{K\,\textcolor{#2a78d6}{C_{B}}\,\textcolor{#eb6834}{V_{K}}^{2}}{100}, \qquad K = 5.74\,S^{0.76}$$

where

\(S_{max}\)maximum squat at the bow or the sternm
\(K\)blockage factor term, 1 for S of 0.10 or less, 2 for S of 0.25
\(C_{B}\)block coefficient
\(V_{K}\)ship speedkn
\(S\)blockage factor of the channel, 0.10 to 0.25 in the stated range

The paper states the formula for a water depth of 1.10 to 1.4 times the draft and a blockage factor of 0.10 to 0.25. The block coefficient range is 0.5 to 0.85. At \( K = 1 \), a ship with \( C_B = 0.80 \) at 10 knots gives 0.80 m. In a confined channel at \( K = 2 \), the same ship gives 1.60 m. The same paper states that ships with \( C_B \) above 0.7 tend to squat by the bow, and finer ships by the stern.

The squat effect article also uses an earlier Barrass form with a blockage term and the speed to the power 2.08. The two formulas are different, so a value from one cannot be checked against the other.

MGN 199 (M) treats a depth of less than twice the draft as shallow water (9.1). Paragraph 9.1.3 states that “relatively high speeds in very shallow water must be avoided due to the danger of grounding because of squat”. IMO resolution A.893(21), paragraph 3.2.2, lists the allowance for squat among the elements of a passage plan. The shallow-water resistance of the hull also rises in the same conditions. MAN Energy Solutions states that shallow water has no influence on resistance where the depth is more than 10 times the draft. The same page states that squat is “primarily seen at elevated Froude numbers” (5510-0004-04, p. 13).

Block coefficient, displacement and deadweight

At fixed length, breadth and draft, each 0.01 of block coefficient adds 1% of the box volume to the displacement. The deadweight rises by the same mass. Where the lightship mass does not change, the added displacement is all deadweight.

Hydrostatic relation

Displacement and the deadweight gained per step in C_B

$$\textcolor{#1baf7a}{\Delta} = \rho\,\textcolor{#2a78d6}{C_{B}}\,L\,B\,T$$
$$\delta\textcolor{#1baf7a}{\Delta} = \rho\,L\,B\,T\,\delta\textcolor{#2a78d6}{C_{B}}$$

where

\(\Delta\)moulded displacementt
\(\rho\)water density, 1.025 for sea watert/m³
\(C_{B}\)block coefficient at draft T
\(L,\ B,\ T\)length, breadth and draft on one stated basism

For the example ship at its summer draft of 10.33 m, the box volume is 150 × 25 × 10.33 = 38,738 m³. An increase of 0.01 in \( C_B \) adds 387 m³, or 397 t in sea water of density 1.025. At \( C_B = 0.80 \) the summer displacement is 31,765 t.

The tonnes per centimetre immersion depends on the waterplane area, not on \( C_B \). For the example ship, \( C_{WP} = 0.88 \) gives a waterplane area of 3,300 m² and a TPC of 33.83 t/cm in sea water. A naval architect uses \( C_B \) for the volume and \( C_{WP} \) for the change of draft with load.

Changes to the block coefficient in service and conversion

Any change to the underwater hull volume or to the principal dimensions changes the block coefficient. A bulbous bow retrofit adds or removes volume forward. A lengthening adds a parallel middle body at the full section, which raises \( C_P \) and \( C_B \) at the same breadth and draft.

MARPOL Annex VI Regulation 2.2.17 defines a major conversion. Limb .5 covers a change “which substantially alters the energy efficiency of the ship”. After a major conversion, Regulation 5.4.8 requires the attained EEXI to be “recalculated as necessary”. The Administration decides whether a given hull change is a major conversion.

A change to the hull form also changes the hydrostatic tables, the load line block coefficient and the class block coefficient. Each value is recalculated on its own basis. The numerical effect depends on the hull, so a value for one retrofit is not a value for another.

Common misconceptions about the block coefficient

The most common error is to treat the block coefficient as one fixed number for a ship. The value depends on the draft, the length basis and the breadth definition. One hull has a load line value, a class value and an EEDI value.

  • “The Load Line Convention uses the length between perpendiculars.” It uses the freeboard length of Annex I Reg 3(1), on the waterline at 0.85D.
  • “A block coefficient below 0.68 reduces the freeboard.” Reg 30 applies only above 0.68. Below 0.68 there is no correction in either direction.
  • “UR S2 takes C_b at the summer draft.” Rev.2 of June 2019 uses the scantling draft. That draft is not less than the draft at the assigned freeboard.
  • “The EEDI is calculated from \( C_B \) through a resistance formula.” The EEDI uses the reference speed from the speed-power curve. \( C_B \) enters only through \( f_j \) and \( f_{iCb} \).
  • “The CII depends on hull fullness.” Regulation 28 uses fuel, capacity and distance. Hull form affects fuel consumption, but \( C_B \) is not a term of the CII.
  • “A fuller hull is less efficient.” No rule rates \( C_B \) as good or bad. The EEDI rates CO2 per capacity-mile, and a fuller hull also carries more cargo at the same dimensions.
  • “The minimum propulsion power is calculated from the block coefficient.” Level 1 of MEPC.1/Circ.850/Rev.3 uses deadweight only. \( C_B \) appears only in the optional semi-empirical method of the appendix.

Limitations of the block coefficient

The block coefficient is a single number, so it cannot describe where the volume sits along the length or in the section. Two hulls with the same \( C_B \) can have different resistance and seakeeping. The prismatic coefficient, the midship section coefficient and the longitudinal center of buoyancy carry that information.

The worked values on this page are for one example ship with a constant \( C_B \) of 0.80. A real hull has a different value at each draft. Take every rule value from the approved hydrostatic data for the ship, on the basis that the rule states.

The UR S11 and CSR examples apply one length and one \( C_B \) to both formulas for illustration. A real calculation uses the rule length, the distribution factor along the length and the still water moments from the loading manual. The CSR text cited is the January 2024 edition; a later edition can change the factors.

The IS Code does not state the length basis of its \( C_B \). The MEPC.364(79) Table 3 values are regulatory reference values, not the measured average of a current fleet.

The simplified squat formula on this page is taken from a peer-reviewed secondary paper, not from Barrass’s own text. The paper does not state whether the speed is through the water or over the ground. The wake and thrust deduction estimates are for single-screw ships: MAN Table 2.02 gives lower wake ranges for twin-screw hulls, 0.10 to 0.25 with a single skeg and 0.15 to 0.35 with twin skegs.

Frequently Asked Questions (FAQs)

What is the block coefficient of a ship?

The block coefficient is the moulded displaced volume divided by the product of length, breadth and draft.

The ratio shows how much of that box the underwater hull fills, so 1.0 describes a box-shaped hull.

Is the block coefficient dimensionless?

Yes, the block coefficient has no unit.

The ratio divides a volume by a volume, so a value of 0.80 is the same in metric and customary units.

Can the block coefficient be greater than 1?

No, a displacement hull cannot fill more than its own box, so the block coefficient cannot exceed 1.0.

Annex I Reg 30 of the Load Line Convention also states that the block coefficient is not taken greater than 1.0.

What is the block coefficient of a barge?

A box-shaped barge has a block coefficient of 1.0, or very close to it.

The 2008 IS Code treats a pontoon as a hull with a block coefficient of 0.9 or greater (Introduction, 2.16).

Which draft does the Load Line Convention use for the block coefficient?

The Load Line Convention takes the block coefficient at 85 percent of the least moulded depth, under Annex I Reg 3(7).

The length is the freeboard length of Reg 3(1), and the volume is moulded, excluding appendages.

Which draft does IACS use for the block coefficient?

IACS UR S2 Rev.2 (June 2019) takes the block coefficient at the scantling draft, on the rule length.

IACS members applied Rev.2 from 1 July 2020, and the scantling draft is not less than the draft at the assigned freeboard.

Which draft does the EEDI use for the block coefficient?

The EEDI guidelines, resolution MEPC.364(79), take the block coefficient at the summer load line draft.

The length has the same wording as the load line length of Annex I Reg 3(1).

Is the block coefficient calculated on LBP or on the waterline length?

The basis depends on the rule.

The Load Line Convention and the EEDI guidelines use the freeboard length on the waterline at 0.85D. IACS uses the rule length at the scantling draft, and a design office often uses LBP or the waterline length.

Why does the same ship have several block coefficients?

Each instrument fixes its own length, breadth and draft.

The load line value is at 0.85D, the class value at the scantling draft and the EEDI value at the summer draft. Each value is correct for its own rule.

Does the block coefficient change with draft?

Yes, the block coefficient changes with draft, and it usually rises as the draft increases because most hulls have fuller sections higher up.

The hydrostatic tables give its value at each draft.

Is the block coefficient different in ballast and laden?

Yes, a ship in ballast floats at a lower draft, so its block coefficient is usually lower than when laden.

The rules take the coefficient at their own stated draft, not at the current loading condition.

Is the block coefficient based on moulded or extreme displacement?

All four rule definitions use the moulded volume, which excludes the shell plating and the appendages.

A draft survey works from the actual displacement in tonnes, which includes them.

How do I convert block coefficient to displacement?

Multiply the block coefficient by length, breadth, draft and water density.

For the example ship, 0.80 x 150 m x 25 m x 10.33 m x 1.025 t per cubic metre gives 31,765 t.

How do I find the block coefficient from a lines plan?

Integrate the station areas along the length, for example with Simpson’s first rule, and divide the volume by length times breadth times draft.

The station areas come from the half-breadths in the offset table.

What is the difference between block coefficient and prismatic coefficient?

The block coefficient compares the volume with the full box.

The prismatic coefficient compares the volume with a prism of the midship section over the length. The block coefficient equals the prismatic coefficient times the midship section coefficient.

Does a block coefficient below 0.68 reduce the freeboard?

No, Annex I Reg 30 of the Load Line Convention applies only where the block coefficient exceeds 0.68.

Below 0.68 there is no correction in either direction.

How does a high block coefficient change the required freeboard?

Above 0.68, Reg 30 multiplies the tabular freeboard by the block coefficient plus 0.68, divided by 1.36.

At 0.80 the factor is 1.0882, which adds 204 mm to a 2,315 mm tabular freeboard.

Why does the minimum bow height formula contain the block coefficient?

Annex I Reg 39(1) includes the block coefficient with a positive term of 0.609, so a fuller hull needs a higher bow, other terms equal.

The regulation states the formula and does not explain the term.

Where does the block coefficient enter the IS Code weather criterion?

The block coefficient sets factor X2 in the angle of roll of the 2008 IS Code, Part A, 2.3.4.

X2 is 0.75 at 0.45 or less and 1.00 at 0.70 or more, from Table 2.3.4-2.

Does the IS Code general intact stability criterion use the block coefficient?

No, the general criteria of Part A, 2.2, use areas and values of the righting arm curve and the metacentric height.

The block coefficient is in the weather criterion of Part A, 2.3, and in the pontoon definition.

What is the minimum block coefficient in the IACS wave bending moment?

IACS UR S11 Rev.10 takes the block coefficient as not less than 0.6.

The floor applies in the wave bending moment, the wave shear force and the minimum moment of inertia. A ship below 0.6 is also a case for special additional considerations under S11.1.

Does UR S11 apply to bulk carriers, tankers and container ships?

UR S11 does not apply to bulk carriers and oil tankers built to the Common Structural Rules, or to container ships, which use UR S11A.

UR S11 applies to other steel ships of 90 m and above in unrestricted service.

How does the block coefficient change the hogging and sagging moments?

Under UR S11 the hogging wave moment is proportional to the block coefficient and the sagging moment to the block coefficient plus 0.7.

At a block coefficient of 0.80 the sagging moment is about 8.6 percent larger.

Do the Common Structural Rules use the block coefficient?

Yes, CSR Part 1, Chapter 4, Section 4 uses it in the vertical wave bending moment.

CSR defines it from the mass displacement at the scantling draft divided by 1.025, and no 0.6 floor applies there.

Does the EEDI formula contain the block coefficient?

The block coefficient is only in two correction factors of MEPC.364(79).

The general cargo ship factor fj is in paragraph 2.2.8.4, and the ice-class factor fiCb is in paragraph 2.2.11.1. The reference speed comes from the speed-power curve.

What is fiCb in the EEDI?

fiCb is the capacity correction for improved ice-going capability: the Table 3 reference block coefficient divided by the ship’s block coefficient, not less than 1.0.

The factor applies only to ice-classed bulk carriers, tankers and general cargo ships.

What reference block coefficient does IMO use for a 60,000 DWT bulk carrier?

MEPC.364(79) Table 3 gives 0.86 for a bulk carrier between 55,000 and 75,000 DWT.

The same table gives 0.83 for a tanker of that size and 0.80 for a general cargo ship of any size.

Does the EEXI use the block coefficient?

The EEXI guidelines, MEPC.350(78), have no block coefficient term of their own.

The guidelines apply the EEDI guideline parameters unless expressly provided otherwise, so fj and fiCb reach the EEXI by that reference.

Does the minimum propulsion power check use the block coefficient?

Level 1 of MEPC.1/Circ.850/Rev.3 uses only deadweight, and the Level 2 simplified wave resistance uses breadth, draft and length.

The block coefficient appears only in the optional semi-empirical method in the appendix.

Is the block coefficient used in the CII?

No, the CII of MARPOL Annex VI Regulation 28 is calculated from fuel consumed and distance sailed.

Hull form affects fuel consumption, but the block coefficient is not a term of the CII formula.

How much deadweight does 0.01 of block coefficient add?

At fixed dimensions and draft, 0.01 of block coefficient adds 1 percent of the box volume.

For the example ship, 150 m by 25 m by 10.33 m, that is 387 cubic metres or 397 t in sea water.

Why do tankers and bulk carriers have high block coefficients?

Their cargo is measured by mass, so a fuller hull carries more deadweight on the same dimensions.

MEPC.364(79) Table 3 uses reference values of 0.78 to 0.86 for these two types.

Does a bulbous bow change the block coefficient?

Yes, a bulb adds immersed volume forward, so it changes the displacement and the block coefficient at a given draft.

All four rule definitions exclude appendages, but the bulb is part of the moulded hull.

Does a lengthening change the block coefficient?

Yes, a lengthening usually raises the block coefficient at the same breadth and draft.

The new parallel middle body has the full midship section along its length. The load line and class values are recalculated for the new hull.

How accurate is a block coefficient from principal dimensions and displacement?

The value is only as accurate as the length, draft and volume basis behind it.

A displacement at one draft mixed with a length or draft on another basis gives a wrong value. The approved hydrostatic data are the reference.

Sources

  1. UN Treaty Series vol. 640 No. 9159. International Convention on Load Lines, 1966 treaties.un.org
  2. IMO Resolution MSC.143(77). Amendments to the Protocol of 1988 relating to the International Convention on Load Lines imo.org
  3. IACS UR S2 Rev.2 (June 2019). Definition of Ship's Length L and of Block Coefficient Cb iacs.s3.af-south-1.amazonaws.com
  4. IACS UR S11 Rev.10 (December 2020). Longitudinal Strength Standard iacs.s3.af-south-1.amazonaws.com
  5. Türk Loydu TL-CSR (July 2024), class reproduction of the IACS 01 JAN 2024 text. Common Structural Rules for Bulk Carriers and Oil Tankers turkloydu.org
  6. IMO Resolution MSC.267(85). International Code on Intact Stability, 2008 imo.org
  7. IMO Resolution MEPC.364(79). 2022 Guidelines on the method of calculation of the attained EEDI for new ships imo.org
  8. IMO Resolution MEPC.350(78). 2022 Guidelines on the method of calculation of the attained EEXI imo.org
  9. IMO Resolution MEPC.328(76). 2021 Revised MARPOL Annex VI imo.org
  10. IMO MEPC.1/Circ.850/Rev.3. Guidelines for determining minimum propulsion power to maintain the manoeuvrability of ships in adverse conditions imo.org
  11. IMO Resolution A.893(21). Guidelines for voyage planning imo.org
  12. UK MCA MGN 199 (M) Amendment 1. Danger of interaction gov.uk
  13. MAN Energy Solutions 5510-0004-04 (October 2018). Basic principles of ship propulsion man-es.com
  14. Barrass (2004), Elsevier. Ship Design and Performance for Masters and Mates, Chapter 1 booksite.elsevier.com
  15. Serban and Panaitescu (2016), Naval Academy Scientific Bulletin XIX(1). Comparison between formulas of maximum ship squat data.ntsb.gov