Cylinder Cover Design and Cooling: Two-Stroke Marine Engines
Two-stroke marine diesel cylinder cover: forged design, cooling water path, valve bores, hydraulic stud tightening, crack sites, class certification and overhaul.
Contents23 sections
The cylinder cover is the removable top of each cylinder on a slow-speed two-stroke crosshead marine diesel engine: a water-cooled part, forged steel on Everllence engines, that forms the upper face of the combustion chamber and carries the central exhaust valve, two or three fuel valves, the starting air valve and the indicator valve. Four-stroke practice, IACS and IMO call the same part the cylinder head. On an Everllence (MAN B&W) G95ME-C10.5, one cover including its valves weighs 6,671 kg, and MAN’s guiding tables give it an expected life of 96,000 running hours.
This article covers the cover on the current engine families: Everllence ME-C and its dual-fuel variants, and WinGD X and X-DF. It explains how the cover is built and fastened, how its cooling water is routed and controlled, what it carries, where it cracks, how it is sealed and overhauled, and what class and the NOx Technical Code require of it.
Function of the cylinder cover in the combustion space
The cover closes the top of the cylinder and takes the full gas load of every firing stroke. On a uniflow-scavenged engine the charge air enters through scavenge ports at the bottom of the cylinder liner and sweeps upward, so the cover carries no inlet valves at all. Its only gas passage is the central exhaust valve bore.
The combustion chamber is bounded by three parts: the piston crown below, the liner around it and the cover above. Each is cooled by its own circuit, and each is overhauled on the same cycle, because the cover has to come off before the piston can be lifted.
A two-stroke fires once per revolution in every cylinder. At the 80 r/min rating of the G95ME-C10.5 and the WinGD X92-B, each cover goes through 80 pressure and temperature cycles a minute, or 4,800 an hour. Across the 96,000-hour life MAN gives the cover, that is roughly 460 million firing cycles, so cover design is governed by fatigue, low-cycle thermal plus high-cycle firing, rather than by a single peak load.
Cylinder cover and cylinder head: the terminology
“Cylinder cover” is the two-stroke term used in Everllence and WinGD manuals. “Cylinder head” is the term in four-stroke practice, in IACS UR M72, where the part appears as items 10 to 13 of Table M72.2, and in the NOx Technical Code 2008, which identifies it by its cylinder head identification number. The two words mean the same component.
Older designs show why the word matters. An opposed-piston engine such as the Doxford closed the combustion space between two pistons and had no cylinder cover in this sense. Loop-scavenged and cross-scavenged engines, including Sulzer’s loop-scavenged RND, had exhaust ports in the liner and a cover without an exhaust valve.
Cover construction and material
The current Everllence cover is a single steel forging. The G60ME-C10.5 project guide (July 2026, section 199 22 96-8.0) describes it as “of forged steel … made in one piece with bores for cooling water, fuel valves, starting valve, indicator valve, and a central bore for the exhaust valve”. The same wording appears in the ME engine description for the G95 to G50ME-C10.7 and C10.5 engines.
Forged steel versus cast covers
Class accepts both routes. IACS UR M72 Rev.3 lists cylinder heads in grey cast iron (GJL), spheroidal graphite cast iron (GJS), cast steel (GS) and forged steel, and sets the documentation for each by bore. Everllence uses forged steel; the WinGD manuals cited do not state the cover material. The cover has to carry high cyclic gas load and thermal cycling across a face interrupted by several large bores, which is the duty steel is chosen for.
Neither Everllence nor WinGD publishes the steel grade, heat treatment or hardness of its covers. The class limits that apply to a forged cover are the machinery forging rules of IACS UR W7 for steel forgings and castings, covered under class certification below.
Cover cooling jacket and slim cover designs
The MAN cover is not a single water-tight body. It carries a separate bolted cooling jacket, sealed with O-rings, and the Everllence spare list names the “cylinder cover complete with fuel, exhaust and starting valves, indicator valve, cooling jacket and sealing rings”. The clearance between the cover and that jacket is where deposits collect when the water treatment fails (MAN SL2014-584, January 2014).
MAN has also changed the cover shape to protect the seals. For S46 and S50MC-C, ME-B and ME-C, and S and L60MC-C engines with slim liners, SL2014-584 records that MAN “introduced a slimmer design of the cylinder cover in order to further reduce the temperature in the O-ring groove”.
Size and mass of the cover
Everllence project guides give the dismantling masses:
| Engine | Cover including valves | Cover dimensions | Exhaust valve alone |
|---|---|---|---|
| G95ME-C10.5, -GI, -LGI | 6,671 kg | Diameter 1,742 mm, height 722 mm | 1,445 kg |
| G60ME-C10.5, -GI, -LGI | 1,822 kg | Diameter 1,100 mm, height 511 mm | 408 kg |
Source: G95ME-C10.5-GI project guide, section 199 11 26-3.1; G60ME-C10.5 project guide, section 199 15 45-6.0 (both July 2026).
The engine room crane tables quote higher figures, 9,650 kg for a G95ME-C10.5 cover complete with exhaust valve and 10,750 kg for the -GI version, because those masses include the lifting tools. The crane is sized to the tool-inclusive figure.
Fastening the cover to the engine frame
On Everllence engines “the cylinder cover is attached to the cylinder frame with studs and nuts tightened with hydraulic jacks” (G60ME-C10.5 project guide). The cover load goes into the cylinder frame, which the long stay bolts clamp to the frame box and the bedplate. The cover studs are a separate fastener system from the stay bolts.
WinGD uses a different arrangement. The X92 Operation Manual (Issue 003) states that “the cylinder liner is on the cylinder jacket and holds the cylinder cover and the water guide jackets. The nuts and the elastic bolts hold these parts together.” On the X92 the cover, the water guide jackets and the liner are clamped to the cylinder jacket as one stack.
Number and arrangement of cover studs
Stud count depends on the engine. MAN SL09-504 (February 2009) introduced a lifting and tilting tool for “all 26-50 cm bore MC/MC-C, ME/ME-C and ME-B type engines with 8 as well as 16 cylinder cover studs”, so both layouts exist in that bore range. Stud counts for the large bores are not published in the project guides.
The studs are long and slender for a reason. A long elastic stud stretches a measurable amount under its preload, so a small settlement of the sealing ring or the thread flanks costs only a small fraction of the clamping force. A short, stiff stud loses a large fraction of its load for the same settlement.
Why hydraulic jacks, not a torque wrench
A hydraulic tightening jack pulls the stud directly. The jack is screwed onto the stud thread above the nut and bears on the cover. When it is pressurised the stud stretches, the nut is run down onto the cover by hand through the window in the jack, and when the pressure is released the stud keeps the load it was stretched to.
Torque tightening cannot do this reliably on a stud of this size. Most of the applied torque goes into friction in the threads and under the nut face, and that friction varies with lubrication, thread condition and face finish, so the same torque gives a different preload on different studs. With a jack, the preload follows from jack pressure and piston area, not from friction.
The jack pressure is specific to the engine and is given in the maker’s instruction manual and on the tool. Neither Everllence nor WinGD publishes it in the project guides or installation manuals, and a figure taken from another engine type must not be used. The Everllence tool lists show the size of the kit: the cylinder cover tightening tools weigh 324 kg on the G95ME-C10.5-GI and 239 kg on the G60ME-C10.5.
MAN issued SL2004-435 on checking hydraulic tools because of the personnel safety risk. A jack at working pressure stores enough energy to eject a fitting, so hoses, couplings and the tool body are inspected before use, and no one stands in line with a pressurised jack.
Cooling water path through the cover
On MAN B&W engines the cover is cooled by the same jacket water that has already cooled the liner. SL2019-687 (December 2019) describes “the four original cooling water connection pipes between the cylinder liner cooling jacket and the cylinder cover cooling jacket”. From the cover, the water passes through the exhaust valve housing, which Everllence describes as “made of cast iron and … arranged for water cooling”, with “a water-cooled bottom piece of steel”. It leaves through the exhaust valve cooling water manifold.
The Everllence jacket water system diagram (section 199 17 29-1.0) requires a venting pipe on the cooling water manifold discharge from the exhaust gas valves, at engine connection M. Air collects at the top of the circuit, which is the exhaust valve cooling space, so that is where the vent sits. The jacket water inlet to the engine is connection K.
MAN has also changed how the water enters small-bore covers. SL2014-584 records a change from a “radial” to a “more ’tangential’ inlet in order to create a forced water rotation” in the cover cooling jacket of S35 and S40MC-C and ME-B, and S46 and S50MC-C, ME-B and ME-C engines. The rotation keeps the water moving in the part of the jacket where deposits would otherwise settle.
Why the cover is cooled close to the combustion face
A cover has to carry high gas load across a face that is also heated by combustion. A thick wall would carry the load well but would run hot on the gas side, since heat must conduct through the whole thickness before the water can remove it. The answer is to bring the cooling water close to the gas-side surface through drilled cooling bores, so the hot face stays at a temperature the steel can sustain over hundreds of millions of cycles.
The bore geometry, the number, diameter, angle and depth of the cooling bores, is proprietary to each engine design. No OEM publishes it in the project guides, and figures for bore diameter or distance from the face should not be taken from secondary sources as design values.
Cooling water path on WinGD X92
WinGD routes the water in the same direction through different parts. The X92 Operation Manual states: “Cooling water flows from the bottom water guide jacket to the top water guide jacket. Then the cooling water flows into the cylinder cover (002) and the exhaust valve cage (001). The cooling water flows back through the cooling water outlet (003).” The same circuit cools the liner, the cover, the exhaust valve cages and the scavenge air cooler.
The X92 has an optional connection that supplies the liner with cooling water at a higher temperature than the cover. A hotter liner wall reduces condensation of sulphuric acid on the running surface, the mechanism of cold corrosion, without raising the cover temperature.
Jacket cooling water temperature and control
Both makers control the jacket cooling water at the engine outlet, at a fixed temperature, independent of load.
| Parameter | Everllence (MAN B&W ME-C) | WinGD X92-B |
|---|---|---|
| Outlet setpoint | 85 °C; 87 °C where a freshwater generator valve is fitted | 90 °C |
| Band at stable load | Fixed by thermostatic valve | 90 °C plus or minus 2 °C |
| Alarm, high outlet temperature | Maker’s alarm list | 95 °C and above |
| Slowdown | Maker’s alarm list | 97 °C and above |
| Inlet temperature, usual | Outlet-controlled; inlet not specified | 72 °C to 90 °C |
| Inlet pressure, usual | Minimum at connection K per project guide | 4.2 to 5 bar; alarm 4.0, slowdown 3.8, shutdown 3.5 bar |
Sources: Everllence G60ME-C10.5 project guide, section 199 17 29-1.0 (July 2026); WinGD MIM X92-B, Issue 2023-03; WinGD X92 Operation Manual, Issue 003, Table 11-6.
The 87 °C MAN setpoint exists because the jacket water also heats the freshwater generator. Where the generator has its own regulating valve, that valve is set at 83 °C and the jacket water cooler valve moves up to 87 °C, so the generator takes heat before the cooler does. The same heat is the usual input to jacket water heat recovery, and the cooler rejects the rest to the central or sea water cooling system.
Warm-up before starting and port stays
The Everllence project guide sets two rules for a stopped engine. In port “the engine jacket cooling water outlet temperature should be kept as high as possible, but not higher than 80 °C. If the temperature is lower than 50 °C, it should be increased to min. 50 °C before start-up.” Preheating is recommended for port stays of “less than four to five days”.
A cold start is hard on the cover because the gas side heats within a few revolutions while the water side is still cold. The face then tries to expand against a cooler body, which puts the combustion surface into compression during the first minutes of running. Preheating removes most of that difference.
Load-dependent liner cooling and the cover outlet
Everllence separates liner and cover temperatures on its latest engines. With load-dependent cylinder liner cooling (LDCL) “the cooling water outlet temperature from the cylinder liner is controlled relative to the engine load, independent of the cooling water outlet from the cylinder cover”, with a liner outlet interval “for example from 70 to 130 °C”. All 95 to 50 bore ME-C10 and ME-C9 engines, including -GI and -LGI, have LDCL monitoring as standard.
On engines with the jacket cooling water bypass (JBB), SL2019-687 allows the bypass to be deactivated on fuel of up to 0.50% sulphur, and “the cover cooling water outlet temperature can be adjusted to 85 °C”. The alarm list carries a differential pressure alarm for jacket water “across cylinder covers and exhaust valves” (PDT 8405) and, on LDCL engines only, a per-cylinder cover outlet temperature sensor (TT 8410), both reported to the engine room monitoring system.
Other system limits that protect the cover
Everllence sets two installation limits in the same section. The maximum water velocity in the external jacket water piping is 3.0 m/s, and the expansion tank must stand “at least 15 m above the top of the main engine exhaust gas valves”. The height keeps the static pressure at the top of the circuit, inside the cover and exhaust valve housing, high enough to stop local boiling and cavitation on the hottest cooled surfaces.
Jacket water treatment and the cover
MAN names the cover as the weak point of the cooling system. SL2014-584 advises, at each piston overhaul, “removal of the cooling jacket on the cylinder cover, clean and re-fit with new O-rings … as the cylinder cover is the most sensitive area of the cooling water system”.
The same letter describes the failure. Deposits from poorly treated water “tend to find the way into the clearances between the cylinder cover and the cooling jacket”, so the cover’s thermal expansion loads the jacket and cracks it. Scale on the cooling bore surfaces also insulates the face, raising the metal temperature on the gas side.
Cooling water treatment to SL2014-584 means:
- a nitrite-borate corrosion inhibitor, dosed to the supplier’s concentration;
- a weekly onboard check of inhibitor concentration, pH and chloride;
- a laboratory sample every three months;
- an annual flush of the system;
- no cathodic protection in the jacket water system, which MAN does not recommend;
- only original-design screws on the cover cooling jacket;
- new O-rings at each refit, with a peroxide-cured O-ring compound available from MAN for the hotter grooves.
The liner cooling jacket O-rings are renewed “typical every 2nd piston overhaul or every 5 years” (SL2023-744).
Valve bores and fittings in the cover
The cover of a current ME-C engine carries the central exhaust valve, two or three fuel valves, the starting air valve and the indicator valve, and on dual-fuel engines the second-fuel valves and their control block. Every one of these is a bore through the cooled wall, and every bore is a place where heat has to flow around a hole.
Central exhaust valve bore
The exhaust valve sits in the central bore. On Everllence engines “the exhaust valve is tightened to the cylinder cover with studs and nuts”. The housing is cast iron and water cooled, the bottom piece is steel and water cooled with “a flame-hardened seat of the Wide-seat design”, and “the exhaust valve spindle is made of Alloy 760”. The valve is opened hydraulically, closed by an air spring and rotated by a vane wheel.
The seat that seals the combustion space is therefore on the exhaust valve bottom piece, not on a ring in the cover. MAN SL2022-729 (September 2022) sets the spindle seat grinding angle at 30.2 degrees (+0.05/-0) against 30.0 degrees (+0/-0.05) on the bottom piece, allows a maximum of 2 mm seat grinding on all 30 to 98 bore engines, and places spindle seat overhaul at 16,000 hours plus or minus 2,000 on bores under 60 and 24,000 hours plus or minus 3,000 on bores of 60 and above.
On bores of 90 and above Everllence offers a safety ring that “is used to provide access to the cylinder liner through the exhaust valve bore of the cylinder cover”. On smaller bores the cover has to be dismantled to inspect the liner.
Fuel valve bores
The Everllence ME engine description states that the cover “is equipped with two or three fuel valves”, arranged around the central exhaust valve. The fuel valves are conventional spring-closed valves opened by fuel pressure. On the ME-C, “the engine has one hydraulically activated fuel oil pressure booster for each cylinder”, controlled by an ELFI or FIVA valve under the ME-C cylinder control unit, on a 300 bar hydraulic supply. The ME-C is not a common-rail engine.
WinGD X-engines are. The X92 Operation Manual states that “the fuel pumps supply the fuel rail with fuel at up to 1000 bar”, and the common-rail injection system feeds two or three injection valves per cylinder. At low load one valve, or one or two, is cut out, and the cut-out valve is rotated “to get an equal thermal load in the combustion chamber”. The rotation keeps a fixed hot spot off the cover and piston crown.
The fuel valve pockets are one of three documented crack sites in the cover. MAN PrimeServ’s repair of a cracked pocket begins by milling out the existing Inconel padding and ends with Inconel welding.
Starting air valve bore
The starting air valve admits air from the starting air system at 30 bar on Everllence engines. It is “opened by control air … and is closed by a spring”, and it must stay shut against firing pressure once the engine runs. A starting valve that leaks lets hot gas back into the starting air pipe, where oil film can ignite.
That hazard is why IACS UR M11, one of the IACS unified requirements for machinery, requires an isolation non-return valve at each engine’s starting air connection and, on direct reversing engines with a main starting manifold, a bursting disc or flame arrester in way of each cylinder’s starting valve. The devices may be omitted on engines of 230 mm bore or less. M11 Rev.1 (August 2026) applies to ships contracted for construction on or after 1 January 2028; earlier ships stay under the 1972 text, which carries the same devices and the same waiver.
MAN SL2023-744 gives the starting valve an 8,000-hour overhaul interval and a 96,000-hour life. The starting air valve pocket is one of the three documented crack sites in the cover.
Indicator valve and pressure sensor bore
The indicator valve gives direct access to the combustion space. On Everllence engines “the bore for the indicator valve is also used for PMI (pressure mean indicated) Auto-tuning by connecting the PMI pressure transducer”, which feeds the PMI system that balances maximum firing pressure and compression pressure between cylinders. WinGD fits a pressure transmitter on each cylinder cover.
The indicator valve is also the tool for a safe start. With the indicator valves open, turning the engine blows out any water, oil or fuel that has collected in the cylinders, and a jet of water from one valve points to a leak in that unit. The indicator bore is the third documented crack site.
Cylinder safety valve
The two makers differ here. MAN issued SL2008-491, “Omission of Cylinder-Cover-Mounted Safety Valves”, for all MAN B&W two-stroke engines, and the fittings list in current Everllence project guides names no cover safety valve.
WinGD X92 covers carry relief valves. The X92 Operation Manual tells the crew to “open the relief valves on all cylinder covers to release the pressure” in the relevant procedure, and to “open the indicator valves or the relief valves on the cylinder cover” before turning. The set pressure is not published in the manual.
Class requirements vary by jurisdiction. No current IACS Unified Requirement requires a relief valve on the cover. The UK MCA instruction MSIS004 Part VIII, 8.1.2.5, which covers UK domestic passenger ship classes III to VI(A), states that “engine cylinders over 230mm in diameter should be fitted with an efficient relief valve” set “to not more than 40% in excess of the maximum design cylinder pressure”. That rule is a national overlay, and individual society rules may carry their own version.
Mechanical and thermal loads on the cover
Two loads act on the cover and they add. Gas pressure bends it once per revolution, and the temperature difference between the gas side and the water side stresses it continuously, with a larger swing at every start, stop and load change.
Gas-pressure load
The upward force on the cover is the cylinder pressure times the bore area:
$$ F = p \cdot \frac{\pi D^{2}}{4} $$where \( F \) is the force on the cover (N), \( p \) the cylinder pressure (Pa) and \( D \) the cylinder bore (m). The bore area of a 950 mm cylinder is 0.709 m². At an illustrative cylinder pressure of 20 MPa (200 bar), which is not an OEM figure for any named engine, the force is 14.2 MN, about 1,450 tonnes-force, and it is reacted by the cover studs at the stud circle.
The cover behaves as a thick plate held at its stud circle and loaded from below. It bends upward in the middle, with the largest bending stress around the central exhaust valve bore and the bridges between bores. The bores themselves concentrate stress, which is why the cracks start there and not on the open face.
Everllence states only that “the engine is designed to withstand a certain Pmax and this Pmax is utilised by the engine control system” (G60ME-C10.5 project guide). The maximum firing pressure of a given engine is in its own documentation. Neither Everllence nor WinGD publishes it in the project guides, so the engine’s own data governs any overhaul or tuning decision.
Thermal load and low-cycle fatigue
The gas side of the cover is hot and the water side is held near the jacket water temperature, so the face tries to expand more than the body behind it. The body holds it back and the face goes into compression when hot. When the engine stops or runs at low load the face cools and the stress reverses.
Each start-stop or large load change is one cycle of that reversal. It is low-cycle thermal fatigue: few cycles, each large. Firing adds a small high-frequency cycle on top. A ship with frequent port calls and manoeuvring puts more thermal cycles on its covers per running hour than one on long ocean passages.
The bores concentrate this load too. Where a bore interrupts the cooled wall, heat entering the face beside it must flow around the bore to reach the water, so the metal next to the bore runs hotter and swings further each cycle. MAN’s documented crack sites, the fuel injector pockets, the starting air valve pocket and the indicator bore, are all bores of this kind.
Causes and locations of cover cracking
MAN PrimeServ states that “small cracks in the area around the fuel injector pockets, starting air valve pocket and/or indicator bore of your cylinder cover … may occur independent of type and size of your engine and that requires welding”. The cracks start on the combustion side where the bore meets the face.
The service conditions that raise the load on those sites are:
- Fuel valve condition. A worn nozzle, an enlarged hole or a dribbling valve directs flame at the face or into the pocket. MAN SL2023-744 tells the crew to “check for burnt grooves at fuel oil valve nozzle holes” at overhaul.
- Cooling water deposits. Scale on the cooling bore walls raises the gas-side metal temperature and the thermal swing (SL2014-584).
- Cold starts and rapid loading. Starting below the 50 °C minimum jacket water temperature, or loading the engine quickly from cold, puts the full thermal swing on a cold body.
- Running above the rated firing pressure. Unbalanced cylinders or wrong fuel timing raise the gas load on one cover above its design basis.
- Starting air valve leakage. Hot gas in the starting valve pocket heats a bore that is not designed to see it.
MAN issued SL1992-301 on high-temperature corrosion of MC-type cylinder covers and SL2008-496 on cleaning and inspection of the cover contact face and combustion area of 60 to 98 bore MC and MC-C engines. Burning of the face, loss of metal where hot gas or spray has attacked it, is the other failure mode MAN documents for the combustion face.
Symptoms of cover leaks and cracks
A crack that reaches from the combustion face to a cooling bore connects two spaces at very different pressures. Firing pressure is far above the jacket water pressure, which is 4.2 to 5 bar at the WinGD X92 inlet, so while the engine runs, gas goes into the water. When the engine stops, cylinder pressure falls below jacket water pressure and water drains into the cylinder.
Running symptoms of a cover crack into the cooling space:
- Gas at the jacket water deaeration points, including the vent on the exhaust valve cooling water manifold.
- Rising or fluctuating expansion tank level, often with gas bubbling at the tank.
- A jacket water pressure disturbance or a low-pressure alarm, and loss of water from the system.
- Where fitted, a changed cover outlet temperature on the affected cylinder (TT 8410 on MAN LDCL engines).
Stopped-engine symptoms:
- Water blowing from one indicator valve when the engine is turned on air or with the turning gear before start.
- Water in the scavenge air space below that unit, found at scavenge drain checks.
The same symptoms can come from a cracked liner, a failed cover-to-liner cooling water seal, or a leaking exhaust valve housing cooling passage, so the defective part is confirmed with the cover off. An engine is never started with water in a cylinder. Water cannot be compressed, and a piston rising onto a water-filled cylinder can bend the piston rod or crack the cover.
Oil or fuel collected in the scavenge space from the same unit is a separate hazard, a scavenge space fire, and is cleared before start.
Cover-to-liner joint and sealing ring
The joint between the cover and the liner top carries the full firing pressure every revolution. It is sealed by a metal sealing ring, listed by Everllence as the “sealing between cylinder cover and liner”, and clamped by the cover studs. MAN issued SL1991-277 on the soft iron sealing ring between cylinder cover and cylinder liner on S, K and L-MC engines.
A soft iron ring works by deforming. When the studs are tightened the ring yields into the surface finish of both faces and closes the leak paths.
The contact faces decide whether the new ring seals. MAN’s SL09-504 and SL2008-496 cover cleaning and inspection of the cover contact face. Carbon deposit, a scratch across the seat or a step from a previous ring will leave a gas path that no clamping force closes. A gas leak at this joint shows as burning on the ring faces and on the liner top at overhaul.
On MAN engines connection pipes carry the water from the liner cooling jacket to the cover cooling jacket, so the water does not cross the gas joint; the cover O-rings are replaced at overhaul (SL2023-744; SL2014-584).
Cover removal, overhaul and refitting
The cover comes off whenever the piston is lifted. MAN SL2023-744 (August 2023) gives guiding piston overhaul intervals for ME and ME-C engines on diesel and heavy fuel:
| Bore | Piston ring and piston overhaul |
|---|---|
| 98 to 80 | 24,000 hours |
| 70 to 50 | 16,000 hours |
| 46 to 35 | 12,000 hours |
Longer intervals are possible under condition-based overhaul to MAN SL07-483, and on the two-stroke overhaul interval schedule the cover’s own life of 96,000 hours spans four overhauls on the largest bores. The interval is set in the ship’s planned maintenance system, which is also where the cover’s weld-up and grinding history is kept.
Removal and lifting
Cover removal is a heavy lift over an open cylinder and runs under a permit to work. The engine is stopped and blocked against turning, the starting air is shut and vented, the jacket water is drained from the unit, and the fuel and hydraulic supplies are isolated. The exhaust valve, fuel valves and pipes are disconnected or lifted with the cover as the maker’s instructions require.
The stud nuts are released with the same hydraulic jacks used to tighten them. The cover is then lifted with the maker’s lifting tool on the engine room crane, rated for the tool-inclusive mass: 9,650 kg on a G95ME-C10.5 diesel engine. MAN’s SL09-504 tilting tool lets small-bore covers be turned over to reach the combustion face.
Inspection at overhaul
MAN SL2023-744 sets the cover inspection items: “Check the holes for first and second fuel valves and the starting air valve when the valves are dismantled. Check for burnt grooves at fuel oil valve nozzle holes. Max. 2 mm grinding in valve holes. … Weld-up if required, up to 2-3 times during service life. Replace O-rings.” On GA engines “a combined grinding value of valve housing and valve holes is limited to 2 mm”.
The combustion face and the bores around the fuel, starting and indicator pockets are crack-checked, the sealing face is cleaned and inspected, and the cooling jacket is removed, cleaned and refitted with new O-rings. The findings go into the maintenance record against that cover’s serial number, because its weld-up count follows the cover, not the cylinder.
Refitting and tightening
The contact faces are cleaned, and the sealing ring and O-rings are renewed as the maker’s instructions require. The cover is lowered square onto the liner and the nuts run down, and the jacks are fitted to the studs and pressurised to the manual’s pressure. Where more studs are fitted than jacks, the maker’s sequence is followed so the cover is pulled down evenly.
After tightening, the jacket water is refilled and vented at the manifold vent, and the unit is checked for leaks. The engine is then turned with the indicator valves open before the first start, and the cover-to-liner joint and the jacket water vents are watched for gas on the first run.
Crack detection and non-destructive testing
Surface cracks in a steel cover are found by magnetic particle testing (MT) or dye penetrant testing (PT). These are the two surface methods of non-destructive testing in marine practice, and IACS UR M72 groups them as “crack detection by MPI or DP”.
MT magnetises the steel and applies fine ferromagnetic particles. A surface-breaking crack disturbs the flux and gathers the particles into a visible line. Current MT principles are ISO 9934-1:2016, and its sensitivity falls off with depth, so it is a surface method. IACS Recommendation No. 68 Rev.1 (April 2021) uses MT as the default surface method on ferritic steel forgings, including cylinder heads and cylinder cover bolts.
PT draws a coloured or fluorescent liquid into an open crack and brings it back out with a developer. It works on any non-porous material and needs no magnetising yoke, so it is used inside small bores, in corners and wherever MT cannot reach. Rec. 68 permits PT on austenitic and duplex steels, to interpret open indications, or when the surveyor asks for it. Current PT principles are ISO 3452-1:2021.
Ultrasonic testing (UT) finds and sizes internal defects and measures how deep a crack goes. At manufacture, IACS UR M72 requires UT and crack detection on forged and cast steel heads above 300 mm bore, and footnote 2 of Rev.3 allows the UT to be done at an earlier production stage where the finished shape makes it impractical. General UT principles are ISO 16810:2024. NDT personnel are certified to a scheme such as ISO 9712:2021; Rec. 68 still cites the withdrawn 2012 edition.
Rec. 68 counts a surface indication as relevant only above 1.5 mm, assesses indications per 225 cm² reference area, and allows no linear or aligned indications on “bolts, which receive a direct fluctuating load, e.g. … cylinder cover bolts”. Those are manufacturing acceptance criteria for new forgings. In-service acceptance of a crack in a running cover is set by the engine maker’s instructions and the class surveyor, not by Rec. 68.
Repair of cracked covers
The documented repair for a cracked fuel injector pocket is Inconel welding. MAN PrimeServ’s on-site sequence is:
- Inspection of cracks.
- Removal of Inconel padding by milling.
- Drilling out the cracked fuel injector hole.
- Preheating and Inconel welding.
- Final machining of the injector bore.
- Final inspection.
The limit on repair is set by the maker. MAN SL2023-744 allows weld-up “up to 2-3 times during service life” and a maximum of 2 mm grinding in the valve holes. A cover beyond either limit is replaced, which is why the repair history of each cover is recorded.
At manufacture, IACS UR W7 clause 9.2 permits repair welding of forgings not subject to torsional fatigue “subject to prior approval of the Classification Society”, with the location, welding procedure, heat treatment and inspection submitted. Shallow defects can instead be ground out to a groove with a bottom radius about three times its depth, and complete removal confirmed by MT or PT (W7 clause 9.1). W7 governs the forging at the forge; it does not set in-service repair rules.
Class certification of new covers
A new cylinder cover is certified under IACS UR M72, Certification of Engine Components. Rev.3 (April 2023) applies to engines with an application for certification dated on or after 1 July 2024; the trigger is the engine’s certification application, not the ship’s contract date. The component route sits inside the wider IACS UR M87 engine certification scheme, adopted in April 2025 for application from 1 January 2027.
Table M72.2 sets the evidence for cylinder heads on engines above 300 mm bore:
| Item | Part | Material | NDE | Hydraulic test | Surveyor visual | Component certificate |
|---|---|---|---|---|---|---|
| 10 | Cylinder head, grey cast iron | W | ||||
| 11 | Cylinder head, SG cast iron | W | ||||
| 12 | Cylinder head, cast steel | W (C+M) | W (UT+CD) | W | X | SC |
| 13 | Forged cylinder head | W (C+M) | W (UT+CD) | W | X | SC |
| 18 | Exhaust gas valve cage (crosshead engines) | W | ||||
| 24 | Bolts and studs for cylinder heads | W (C+M) | W (UT+CD) |
W is a work certificate signed by the manufacturer, SC a Society Certificate issued by the class society, C+M chemical composition and mechanical properties, UT+CD ultrasonic testing plus crack detection by MPI or DP, and X a visual examination of accessible surfaces by the surveyor. Source: IACS UR M72 Rev.3, Table M72.2.
Footnote 3 sets the hydraulic test: “Items are to be tested by hydraulic pressure at the pressure equal to 1.5 times the maximum working pressure”, applied on the water or oil side. Footnote 10 extends hydraulic testing to “those parts filled with cooling water and having the function of containing the water which is in contact with the cylinder or cylinder liner”. The exhaust valve spindle, starting air valve, relief valve and indicator valve are not listed in Table M72.2; clause 2.3 leaves unlisted parts to the society’s consideration.
Material rules for forged and cast covers
A forged cover takes its material rules from IACS UR W7, Hull and machinery steel forgings. Rev.4 applies to ships contracted for construction on or after 1 July 2023 and Rev.5, adopted 28 February 2025, to ships contracted on or after 1 January 2027. The forge must be approved by the class society (clause 2.1), and alloy steels are supplied normalized, normalized and tempered, or quenched and tempered, with “the tempering temperature … not less than 550 °C” (clause 5.2).
W7 Table 2 limits alloy machinery forgings to 0.45% carbon, 0.45% silicon, 0.30% to 1.00% manganese and 0.035% each of phosphorus and sulphur, with at least one of chromium 0.40%, molybdenum 0.15% or nickel 0.40% as a minimum. The specification is submitted for approval. W7 clause 8.4 leaves the NDT method, extent and acceptance “to be agreed with the Classification Society”, naming IACS Recommendation No. 68 as an example of an acceptable standard.
A cast steel cover takes its material rules from IACS UR W8, Hull and machinery steel castings, Rev.5 (2025) for ships contracted from 1 January 2027. For alloy steel castings W8 clause 9.2 states that “repair requires approval from the Classification Society”. The two rules, M72 by engine application date and W7 or W8 by ship contract date, can apply different revisions to the same cover.
Class survey of covers in service
In service the cover is examined when it is opened for overhaul, and that examination is credited to the ship’s continuous machinery survey or planned maintenance scheme. IACS UR Z18 Rev.9 (April 2020) sets the rule that under continuous survey “the interval between consecutive examinations of each item is not to exceed five (5) years”, allows machinery surveys on a planned maintenance basis under UR Z20, and on a condition-monitoring basis under UR Z27.
Z18 has no engine component list. The item list, which items a chief engineer may examine for class credit and when the surveyor must attend, are in each classification society’s own rules.
The cover in the NOx Technical File
A marine diesel engine with a power output above 130 kW (MARPOL Annex VI Regulation 13.1.1.1) is certified to MARPOL Annex VI Regulation 13 under the NOx Technical Code 2008, resolution MEPC.177(58), adopted 10 October 2008, in force 1 July 2010, and amended by MEPC.251(66), in force 1 September 2015. The Code defines components as “interchangeable parts that influence the NOx emissions performance, identified by their design/parts number” (NTC 1.3.3).
The cover can be one of those parts. NTC 6.2.2.3 lists “combustion chamber” among the NOx-influencing parameters, and Appendix VII checks it by “component identification numbers for the cylinder head and piston head”. Whether a given engine’s Technical File designates the cover is set by that file, since NTC 6.2.2.4 allows the Administration to accept fewer parameters.
The consequences are in the record book. NTC 6.2.2.7.1 requires the record book of engine parameters to record “all changes, including like-for-like replacements”. A like-for-like cover from the Technical File is not a substantial modification (NTC 1.3.2.1), but at survey the surveyor checks “that only components of the approved specification, as given by 2.4.1.7, are being used” (NTC 6.2.3.2). A cover whose identification number is not in the file needs the change documented and accepted, and can raise a substantial-modification question under NTC 1.3.2, which MARPOL Annex VI Regulation 13.2 treats as a major conversion for an engine not already certified to a NOx Tier.
Dual-fuel and alternative-fuel cylinder covers
The dual-fuel cover is the diesel cover with more bores. Everllence states that “for dual-fuel engines, the cylinder cover has bores for SF valves, and bores/pipes for supplying and returning SF from the control block to each SF valve”, and “the side of the cylinder cover facing the hydraulic cylinder unit (HCU) block has a face for mounting a special valve block, the SF control block”. The second fuel is “either methanol, LPG, methane, or ethane”, covering the ME-LGIM methanol engines, the ME-LGIP LPG engines and the ME-GI and ethane-burning ME-GIE gas engines.
High-pressure gas injection on the ME-GI
The ME-GI injects natural gas at high pressure through valves in the cover, with a gas block carrying an accumulator and control valves mounted on the “slightly modified” cover. The Everllence fuel gas system section (199 13 52-6.0, June 2025) raises the gas supply “to 300 bar, which is the maximum required pressure at the engine inlet”, fits a supply safety relief valve at 350 bar, and holds sealing oil “20 – 25 bar higher than the gas pressure” so gas cannot leak past the valve spindles into the control oil.
The ME-GI Mk 2 moved pipework into the cover. Everllence service experience describes “new gas injection valves, where the supply of control and sealing oil has been led through bores in the cylinder cover, making high-pressure pipes obsolete”. Each extra bore is another interruption of the cooled wall, so the dual-fuel cover carries more bores than its diesel counterpart. The number of gas injection valves per cover is not published in the project guide.
Low-pressure gas admission on the WinGD X-DF
The WinGD X-DF takes the gas valves out of the cover altogether. WinGD lists the changes as “Gas admission valve (GAV) on the cylinder liner”, “Cylinder liner modified for GAV installation” and “Adapted cylinder cover to accommodate the pilot injectors with the pre-chamber”. Gas below 16 bar enters “via gas admission bores which pass through the cylinder liner wall” during compression.
The X-DF cover carries two pilot fuel pre-chambers per cylinder, fed at up to 1,200 bar. “The water-cooled pre-chamber inserts are manufactured from hot gas corrosion-resistant material … Cooling water channels in the cylinder covers cool the pre-chamber using the existing cooling water circuit for cylinder liner, cover, and exhaust valve” (WinGD, February 2017). The pre-chamber is where the pilot flame starts, and it is cooled from the cover circuit.
Cover arrangements for ammonia two-stroke engines are not published in the project guides cited here, and nothing in this section describes them.
Comparison with four-stroke cylinder heads
The four-stroke cylinder head does the same job on a medium-speed engine with a different layout. The table compares the two.
| Feature | Two-stroke cylinder cover (uniflow crosshead) | Four-stroke cylinder head (trunk piston) |
|---|---|---|
| Gas valves | One central exhaust valve | Inlet and exhaust valves, usually two of each |
| Charge air route | Liner ports, not through the cover | Through inlet valves in the head |
| Fuel valves | Two or three, around the exhaust valve | One central injector |
| Exhaust valve drive | Hydraulic, air-spring closed (ME-C, X) | Camshaft and rocker, or hydraulic |
| Typical mass | 6,671 kg with valves (G95ME-C10.5) | A fraction of that |
| Fastening | Hydraulically tightened studs to the frame or jacket | Hydraulically or torque-tightened studs to the block |
| Overhaul trigger | Piston overhaul, 12,000 to 24,000 h by bore (MAN) | Maker’s head overhaul interval |
The four-stroke head sits on a trunk piston engine and has to find room for four valves, the injector and the cooling passages in a smaller face, so its inter-valve bridges carry the same thermal fatigue problem that the injector pockets carry on a two-stroke cover.
Limitations
The figures in this article are taken from named Everllence, MAN and WinGD documents at the editions given, and they apply to the engines those documents cover. Another engine type, a later tier or a licensee build can differ, and the engine’s own instruction manual governs any overhaul.
Several design values are not published by either maker and are left out on purpose: the cover steel grade and heat treatment, the cooling bore diameter, pitch and distance from the face, the maximum firing pressure of current engines, the cover stud jack pressure and tightening sequence, the stud count on large bores, the relief valve set pressure on WinGD covers, and the cooling water flow per cover. Values for these found in secondary sources should not be used as engineering inputs.
The class material in this article reflects IACS UR M72 Rev.3, UR W7 Rev.5, UR W8 Rev.5, Recommendation No. 68 Rev.1 and UR M11 Rev.1 as published. Several of these apply by ship contract date or engine application date, so the revision that binds a given cover depends on those dates. Society rules, flag-state instructions and the individual engine’s NOx Technical File add requirements not covered here.
Frequently Asked Questions (FAQs)
What is a cylinder cover on a two-stroke marine engine?
The cylinder cover is the removable top of each cylinder on a slow-speed two-stroke crosshead engine.
It forms the upper face of the combustion chamber, carries the central exhaust valve, the fuel valves, the starting air valve and the indicator valve, and is water cooled. On Everllence (MAN B&W) ME-C engines it is a one-piece steel forging studded to the cylinder frame.
Is a cylinder cover the same thing as a cylinder head?
Yes. Two-stroke marine practice says cylinder cover; four-stroke practice, IACS and IMO texts say cylinder head.
IACS UR M72 lists the part as a cylinder head, and the NOx Technical Code 2008 identifies it by its cylinder head identification number.
Why does a uniflow two-stroke cover have only one exhaust valve?
In a uniflow-scavenged engine the charge air enters through ports at the bottom of the liner and sweeps upward, so the only outlet needed at the top is one large central exhaust valve.
The cover therefore has no inlet valves, and the fuel valves are arranged around the exhaust valve instead of at the centre.
How many fuel valves does a two-stroke cylinder cover carry?
Two or three. The Everllence ME engine description states that the cover is equipped with two or three fuel valves.
WinGD X92 engines are built with two or three injection valves, and at low load one valve is cut out and the cut-out valve is rotated to keep the thermal load on the combustion chamber even.
Does an MAN B&W ME-C engine use common rail injection?
No. Each cylinder has one hydraulically activated fuel oil pressure booster, controlled by an ELFI or FIVA valve on a 300 bar hydraulic supply.
High-pressure fuel from the booster opens the conventional fuel valves in the cover and a spring closes them. WinGD X-engines are the two-stroke family that use a common fuel rail, at up to 1,000 bar on the X92.
Does a modern MAN B&W cylinder cover have a safety valve?
No. MAN issued service letter SL2008-491, Omission of Cylinder-Cover-Mounted Safety Valves, covering all MAN B&W two-stroke engines, and the fittings list in current Everllence project guides names no cover safety valve.
WinGD X92 covers do carry relief valves, which the X92 Operation Manual tells the crew to open when releasing cylinder pressure.
Is a cylinder relief valve required by IACS?
No current IACS Unified Requirement requires a cylinder relief valve on the cover.
The rule of a relief valve on cylinders over 230 mm bore, set not more than 40% above the maximum design cylinder pressure, survives in national instructions such as the UK MCA MSIS004 Part VIII, 8.1.2.5, which applies to UK domestic passenger ship classes.
What is the indicator valve on the cover used for?
It gives access to the combustion space for measuring cylinder pressure.
On Everllence ME-C engines the indicator valve bore is also used to connect the PMI pressure transducer for automatic combustion tuning, and WinGD fits a pressure transmitter on each cylinder cover. Opening the indicator valves and turning the engine on air before a start blows out any water or oil that has collected in the cylinders.
What jacket water outlet temperature should a MAN B&W engine run at?
The thermostatic valve for the jacket water cooler is set at 85 °C, or 87 °C where a separate regulating valve is fitted for the freshwater generator, whose own cooler valve is set at 83 °C.
The valve holds the engine outlet at that fixed level independent of load (Everllence G60ME-C10.5 project guide, July 2026, section 199 17 29-1.0).
What jacket water outlet temperature does WinGD specify?
90 °C at the cylinder cooling water outlet on the X92-B and X72-B (WinGD Marine Installation Manuals, Issue 2023-03).
The X92 Operation Manual gives a usual value of 90 °C plus or minus 2 °C at steady load and plus or minus 4 °C during load changes, an alarm at 95 °C and a slowdown at 97 °C.
How warm must the jacket water be before starting a MAN two-stroke engine?
At least 50 °C. If the jacket water is below 50 °C it should be raised to at least 50 °C before start-up, and in port the outlet should be kept as high as possible but not above 80 °C.
Everllence recommends preheating for port stays of less than four to five days.
Why is the jacket water kept hot rather than as cold as possible?
The cover combustion face sees combustion gas on one side and cooling water on the other, so the water temperature sets the metal temperature on the cooled side.
A warm, fixed water temperature limits the temperature difference through the cover wall and the swing between stopped and running conditions, both of which drive thermal fatigue. Both makers therefore control the outlet at a fixed 85 °C to 90 °C instead of cooling harder, and MAN uses the same heat for the freshwater generator.
Where does cylinder cover cooling water come from on an ME-C engine?
From the cylinder liner cooling jacket.
On MAN B&W engines four connection pipes carry the water from the liner cooling jacket to the cylinder cover cooling jacket (SL2019-687); from the cover it passes through the water-cooled exhaust valve housing and leaves via the exhaust valve cooling water manifold, which carries the deaeration connection.
How does cooling water flow through a WinGD X92 cover?
From the bottom water guide jacket to the top water guide jacket, then into the cylinder cover and the exhaust valve cage, and out through the cooling water outlet (WinGD X92 Operation Manual, Issue 003).
An optional connection lets the liner be supplied with cooling water at a higher temperature than the cover.
What is load-dependent cylinder liner cooling and does it change the cover temperature?
Load-dependent cylinder liner cooling (LDCL) on MAN B&W engines controls the liner cooling water outlet temperature against engine load, independent of the cover outlet, with a liner outlet range as wide as 70 °C to 130 °C.
The cover stays on the fixed jacket water setpoint. LDCL monitoring is standard on 95 to 50 bore ME-C10 and ME-C9 engines, including -GI and -LGI variants.
Why do cylinder cover cooling jackets crack?
MAN SL2014-584 attributes cracked cover cooling jackets to deposits from poorly treated cooling water, which collect in the clearance between the cover and its bolted cooling jacket so the expanding cover loads the jacket.
The remedies are correct inhibitor treatment, cleaning the jacket and fitting new O-rings at each piston overhaul, and using only original-design jacket screws.
What water treatment does MAN recommend for jacket cooling water?
MAN SL2014-584 recommends nitrite-borate corrosion inhibitors, a weekly onboard check of inhibitor concentration, pH and chloride, a laboratory sample every three months and an annual system flush.
It does not recommend cathodic protection in the jacket water system, and it names the cylinder cover as the most sensitive area of the cooling water system.
Where do cylinder covers crack?
MAN PrimeServ documents small cracks around the fuel injector pockets, the starting air valve pocket and the indicator bore, and states that they can occur independent of engine type and size.
These are the places where a bore interrupts the cooled wall close to the combustion face, so heat has to flow around the bore and the local temperature swing each cycle is largest.
How is a cracked fuel injector pocket repaired?
MAN PrimeServ’s on-site sequence is: inspect the cracks, remove the Inconel padding by milling, drill out the cracked fuel injector hole, preheat and weld with Inconel, machine the injector bore to final size, and carry out a final inspection.
The same Inconel padding protects the pocket in service.
How many times can a cylinder cover be weld repaired?
MAN SL2023-744 allows weld-up if required up to 2 to 3 times during the cover’s service life, with a maximum of 2 mm grinding in the valve holes.
Beyond those limits the cover is replaced. On GA engines the 2 mm limit applies to the combined grinding of valve housing and valve holes.
What is the expected service life of a MAN B&W cylinder cover?
96,000 running hours, according to the guiding overhaul tables in MAN SL2023-744 (August 2023).
The starting air valve has the same 96,000-hour expected life with an 8,000-hour overhaul interval, and the exhaust valve on 98 to 60 bore engines has a 72,000-hour life.
How often is the cylinder cover lifted?
The cover comes off for each piston overhaul.
MAN SL2023-744 gives guiding piston overhaul intervals of 24,000 hours for 98 to 80 bore engines, 16,000 hours for 70 to 50 bore and 12,000 hours for 46 to 35 bore on ME and ME-C engines, with longer intervals possible under condition-based overhaul.
What does a large two-stroke cylinder cover weigh?
The Everllence G95ME-C10.5-GI project guide gives 6,671 kg for the cylinder cover including valves, 1,742 mm in diameter and 722 mm high, with the exhaust valve alone at 1,445 kg.
The G60ME-C10.5 cover including valves is 1,822 kg. Crane capacity tables use higher figures because they include the lifting tools.
Why are cylinder cover studs tightened hydraulically instead of torqued?
A hydraulic jack stretches the stud directly to a known load, the nut is run down while the stud is held stretched, and the load is kept when the pressure is released.
Torque tightening would lose most of the input to thread and nut-face friction, which varies with lubrication and surface condition, so the resulting preload on a stud this size would be uncertain.
What jack pressure is used for cylinder cover studs?
The pressure is engine-specific and is given in the engine maker’s instruction manual and on the tightening tool.
Neither Everllence nor WinGD publishes it in their project guides or installation manuals, so a figure from another engine type must not be used.
How many studs hold a cylinder cover?
It depends on the engine. MAN SL09-504 covers 26 to 50 cm bore MC, MC-C, ME, ME-C and ME-B engines built with either 8 or 16 cylinder cover studs.
On WinGD X92 engines elastic bolts and nuts hold the cover, the water guide jackets and the liner to the cylinder jacket.
What seals the cylinder cover against the liner?
A sealing ring at the cover-to-liner joint, listed by Everllence as the sealing between cylinder cover and liner.
MAN issued SL1991-277 on the soft iron sealing ring between cylinder cover and cylinder liner on S, K and L-MC engines.
How do you know a cylinder cover is cracked while the engine is running?
A crack that reaches from the combustion face into a cooling bore lets combustion gas at firing pressure into the jacket water, which is at a few bar.
The gas shows up at the deaeration points, as a fluctuating or rising expansion tank level, and as a jacket water pressure disturbance. The cylinder is then isolated by comparing it with its neighbours and confirmed with the engine stopped.
What causes water in the cylinder of a two-stroke engine?
Water in the combustion space with the engine stopped comes from a crack in the cover, a leaking cover-to-liner cooling water seal, a cracked liner, or a leaking exhaust valve housing cooling passage.
It is found by opening the indicator valves and turning the engine on air or with the turning gear before a start, and it must be traced before the engine is run, because water cannot be compressed.
What is burning on the cover combustion face?
Local loss of metal where hot gas or a fuel spray has attacked the face.
MAN SL2023-744 tells the crew to check for burnt grooves at the fuel valve nozzle holes when the fuel valves are out, and MAN issued SL1992-301 on high-temperature corrosion of MC-type cylinder covers. A worn or dribbling fuel valve nozzle is the usual source of a spray that impinges on the face.
Which class requirement governs certification of a new cylinder cover?
IACS UR M72, Certification of Engine Components, Rev.3 (April 2023), applied to engines with an application for certification dated on or after 1 July 2024.
For forged or cast steel heads on engines above 300 mm bore it requires work certificates for material and for ultrasonic and crack detection, a hydraulic test, surveyor visual examination and a Society Certificate.
What hydraulic test does class require on a new cover?
IACS UR M72 footnote 3 requires the water or oil side to be tested at 1.5 times the maximum working pressure, and footnote 10 extends hydraulic testing to parts containing cooling water in contact with the cylinder or liner.
For cylinder heads on engines above 300 mm bore the test is documented by a work certificate.
Are cylinder cover studs certified by class?
IACS UR M72 item 24, bolts and studs for cylinder heads on engines above 300 mm bore, requires work certificates for chemical composition and mechanical properties and for ultrasonic testing and crack detection, with no Society Certificate.
IACS Recommendation No. 68 Rev.1 does not permit linear or aligned surface indications on cylinder cover bolts.
Can a cylinder cover be cast instead of forged?
Yes. IACS UR M72 lists cylinder heads in grey cast iron, spheroidal graphite cast iron, cast steel and forged steel.
Grey and SG iron heads above 300 mm bore need only a hydraulic test work certificate, while cast steel heads are documented like forged heads and take their material rules from IACS UR W8.
What material rules apply to a forged cylinder cover?
IACS UR W7, Hull and machinery steel forgings.
Alloy machinery forgings are limited to 0.45% carbon and 0.45% silicon, 0.30% to 1.00% manganese and 0.035% each of phosphorus and sulphur, with a minimum chromium, molybdenum or nickel content, and are tempered at not less than 550 °C. Rev.4 applies to ships contracted from 1 July 2023 and Rev.5 from 1 January 2027.
Can a new cover forging be repaired by welding at the forge?
Only with the prior approval of the classification society.
IACS UR W7 clause 9.2 allows repair welding of forgings not subject to torsional fatigue subject to that approval, with the repair location, welding procedure, heat treatment and inspection submitted. Shallow defects may instead be ground out to a groove radius of about three times its depth and checked by magnetic particle or penetrant testing.
When is magnetic particle testing used instead of dye penetrant on a cover?
Magnetic particle testing is the default surface method on ferritic steel forgings such as covers and studs; IACS Recommendation No. 68 permits penetrant testing for austenitic and duplex steels, to interpret open indications, or when the surveyor asks for it.
Penetrant is also used on shipboard where a magnetising yoke cannot reach, such as inside small bores.
Does the classification society survey the cylinder cover?
The cover is examined when opened for overhaul under the ship’s continuous machinery survey or planned maintenance scheme.
IACS UR Z18 Rev.9 sets a five-year maximum interval between examinations of each item under continuous survey but contains no engine component list; the item list and the credit for chief engineer examinations are in each society’s own rules.
Is the cylinder cover a NOx-critical component?
It can be. NOx Technical Code 2008 Appendix VII checks the combustion chamber parameter by the identification numbers of the cylinder head and the piston head, and whether a given engine’s Technical File designates the cover is set by that file.
Every change, including a like-for-like replacement, is recorded in the record book of engine parameters under NTC 6.2.2.7.1.
What happens if a non-OEM replacement cover is fitted?
Where the Technical File designates the cover, the surveyor verifies that only components of the approved specification are used (NTC 6.2.3.2).
A cover whose identification number is not in the file needs the change documented and accepted by the Administration, and can raise a substantial-modification question under NTC 1.3.2, which MARPOL Annex VI Regulation 13.2 treats as a major conversion for an engine not already certified to Tier I, II or III.
How does a dual-fuel MAN B&W cover differ from a diesel cover?
On second-fuel ME-C engines the cover has bores for the second-fuel valves, bores or pipes for supplying and returning the fuel from a control block, and a machined face on the hydraulic cylinder unit side for mounting that block.
The second fuel is methanol, LPG, methane or ethane depending on the engine variant (Everllence G60ME-C10.5 project guide, July 2026).
What gas pressure reaches an ME-GI cylinder cover?
Up to 300 bar, which Everllence states is the maximum required pressure at the engine inlet, with a supply safety relief valve at 350 bar and sealing oil held 20 to 25 bar above the gas pressure.
On ME-GI Mk 2 engines the control and sealing oil is led through bores in the cylinder cover, removing high-pressure pipes.
Where are the gas valves on a WinGD X-DF engine?
On the cylinder liner, not the cover.
Gas below 16 bar enters through admission bores in the liner wall, and the cover is adapted to carry two water-cooled pilot pre-chambers made from hot-gas corrosion-resistant material, fed with pilot fuel at up to 1,200 bar (WinGD, February 2017).
Can the liner be inspected without lifting the cover?
On MAN B&W engines of bore 90 and above, an optional safety ring allows access to the cylinder liner through the exhaust valve bore of the cover.
Smaller bores need the cover removed (Everllence G60ME-C10.5 project guide, section 199 12 30-4.1).
How does a four-stroke cylinder head differ from a two-stroke cover?
A four-stroke head carries inlet and exhaust valves, usually two of each, plus the fuel injector, because the four-stroke cycle draws charge air through the head.
A uniflow two-stroke cover carries only one central exhaust valve, since charge air enters through the liner ports, and it is much larger: a G95 cover including valves weighs 6,671 kg.
What checks are made on the cover valve bores at overhaul?
MAN SL2023-744 tells the crew to check the holes for the first and second fuel valves and the starting air valve when the valves are dismantled, to check for burnt grooves at the fuel valve nozzle holes, to limit grinding in the valve holes to 2 mm, and to replace the O-rings.
What protects the starting air system from an explosion caused by a leaking starting air valve?
IACS UR M11 requires an isolation non-return valve at each engine’s starting air connection and, on direct reversing engines with a main starting manifold, a bursting disc or flame arrester in way of each cylinder’s starting valve.
The disc or arrester may be omitted on engines of 230 mm bore or less. Rev.1 applies to ships contracted from 1 January 2028.
No question matches. Try a shorter or different word.
Sources
- Everllence B&W G60ME-C10.5 Project Guide, Edition 1.0, July 2026. engine description 199 22 96-8.0, exhaust valve, jacket cooling water 199 17 29-1.0, dismantling masses 199 15 45-6.0 man-es.com
- Everllence B&W G95ME-C10.5-GI Project Guide, July 2026. cylinder cover mass 199 11 26-3.1, hydraulic power supply Fig. 16.01.02, tools and spares man-es.com
- Everllence project guide section 199 13 52-6.0, Fuel gas system, ME-GI engine (June 2025) man-es.com
- MAN Energy Solutions Service Letter SL2023-744, Guiding overhaul intervals, updated tables (August 2023) man-es.com
- MAN Diesel and Turbo Service Letter SL2014-584, Cooling water system, maintenance and recommendations (January 2014) man-es.com
- MAN Energy Solutions Service Letter SL2019-687, Liner jacket cooling water system update (December 2019) man-es.com
- MAN Energy Solutions Service Letter SL2022-729, Preventive grinding of exhaust valve seats (September 2022) man-es.com
- MAN Diesel Service Letter SL09-504, New lifting and tilting tool, cleaning and inspection of cylinder cover contact face and combustion area (February 2009) man-es.com
- MAN PrimeServ, On-site recovery. cylinder cover crack repair by Inconel welding (2019) man-es.com
- WinGD X92 Operation Manual, Issue 003 (December 2020). cylinder liner and cover, cooling water, operating values wingd.com
- WinGD Marine Installation Manual X92-B, Issue 2023-03 wingd.com
- WinGD, Application of WinGD X-DF engines for LNG fuelled vessels (February 2017) wingd.com
- IACS UR M72 Rev.3 (April 2023), Certification of Engine Components. Table M72.2 iacs.s3.af-south-1.amazonaws.com
- IACS UR W7 Rev.5 (February 2025), Hull and machinery steel forgings classnk.or.jp
- IACS Recommendation No. 68 Rev.1 (April 2021), Guidelines for non-destructive testing of hull and machinery steel forgings iacs.s3.af-south-1.amazonaws.com
- IACS UR M11 Rev.1 (August 2026), Protective devices for starting air mains classnk.or.jp
- IMO Resolution MEPC.177(58), NOx Technical Code 2008, adopted 10 October 2008. 1.3.2, 2.4.1.7, 6.2.2 and Appendix VII imo.org
- UK Maritime and Coastguard Agency, MSIS004 Part VIII, Boilers and Machinery. 8.1.2.5 cylinder relief valves assets.publishing.service.gov.uk
- IACS UR Z18 Rev.9 (April 2020), Survey of Machinery. 1.3 continuous survey iacs.s3.af-south-1.amazonaws.com