Hydrostatics and Bonjean Curves: Tables, TPC and MCT1cm

Hydrostatic curves give displacement, TPC, MCT1cm, KB, LCB, LCF and KM at each draft; Bonjean curves give section areas for trim, strength and draft surveys.

Contents14 sections

Ship hydrostatics is the set of properties of a hull floating upright in still water, tabulated against draft. The main particulars are displacement, TPC, MCT 1 cm, KB, LCB, LCF, KM and the form coefficients. Bonjean curves give the immersed area of each transverse section against draft. They give displacement and the center of buoyancy for any trimmed or deflected waterline. The 2008 IS Code, Part B 3.6.4.4, lists “hydrostatic curves or tables” as stability booklet content. A draft survey under ECE/ENERGY/19 starts from the same tables.

The hydrostatic data are the first calculation in the intact stability chain. The cross curves of stability and KN tables come next, then the GZ curve and righting arm, and then the criteria. Each step needs the waterline and the hull shape below it, and hydrostatics supplies both.

Archimedes’ principle and the displacement equation

A floating ship displaces a mass of water equal to its own mass, so displacement is the water density times the volume below the waterline. The rule card gives the relation. Every particular in a hydrostatic table is a property of that underwater volume or of the waterplane that bounds it.

Hydrostatic relation

Displacement

$$\textcolor{#2a78d6}{\Delta} = \textcolor{#eb6834}{\rho}\,\textcolor{#1baf7a}{\nabla}$$

where

\(\Delta\)displacement, the mass of water the hull displacest
\(\rho\)density of the water the ship floats int/m³
\(\nabla\)displaced volume below the waterlinem³

Displacement depends on density, so the same ship floats deeper in fresh water than in salt water. The center of buoyancy, B, is the centroid of the displaced volume. The ship is in equilibrium only when B and the center of gravity, G, are on the same vertical line.

Displacement is the sum of the lightweight and the deadweight. The lightweight comes from the inclining experiment and lightweight survey. The 2008 IS Code, Introduction 2.24, says that the lightweight survey uses “the ship’s hydrostatic data” to find lightship displacement and LCG. The deadweight is what the ship carries. The volume above the waterline and below the watertight deck is the reserve buoyancy that the load line protects.

The introduction to ECE/ENERGY/19 states that the draft survey method rests on “Archimedes’ law of buoyancy”. It adds that the method was “further refined by formulas developed by European naval architects in the nineteenth century”. The formulas it then prints use the hydrostatic table at every step.

Hydrostatic particulars: definitions, symbols and units

The hydrostatic particulars are the properties of the underwater volume and the waterplane at each draft, calculated for the ship upright. The ITTC Symbols and Terminology List, Version 2024, gives the symbols. The International Towing Tank Conference defines BM as I_T / ∇ = KM − KB. It measures LCB and LCF from a stated reference point “such as” midships.

IACS UR L5 Rev.4 (June 2020), Table 1, lists the hydrostatic outputs on which onboard stability software is tested. The list is a practical definition of what a hydrostatic table contains:

ParticularSymbolUnitUR L5 Rev.4 tolerance
DisplacementΔt±2%
Longitudinal center of buoyancy, from APLCBm±1% or 50 cm
Longitudinal center of flotation, from APLCFm±1% or 50 cm
Vertical center of buoyancyVCB (KB)m±1% or 5 cm
Transverse center of buoyancyTCBm±0.5% of B or 5 cm
Moment to change trim 1 cmMCT 1 cmt·m/cm±2%
Transverse metacentric heightGMtm±1% or 5 cm
Longitudinal metacentric heightGMlm±1% or 50 cm
DraftsTm±1% or 5 cm

Note 2 to Table 1 states that “the allowable tolerance is the greater of the two values”. UR L5 Rev.4 applies to ships contracted on or after 1 July 2021.

Displacement and displaced volume

Displacement Δ is the mass of the ship in tonnes, and the displaced volume ∇ is the volume below the waterline in m³. The table gives both, or gives Δ at a stated reference density. The 2008 IS Code, Part B 3.5.1, asks for the volume to the upper surface of the deck sheathing. It adds that “appendages and sea chests need to be considered when calculating hydrostatics”. An approved table therefore includes more than the molded hull.

The 1988 Load Lines Protocol, Annex B as amended by MSC.143(77), uses 1.025 for salt water in the damage assumptions of Regulation 27. Regulation 40(7) gives the fresh water freeboard for water “of unit density”. A hydrostatic table states the reference density it was calculated for. The draft survey code calls that value RD.

Tonnes per centimetre immersion

Tonnes per centimetre immersion (TPC) is the mass that changes the mean draft by 1 cm. TPC equals the waterplane area times the density, divided by 100. A 1 cm layer of the waterplane holds A_W / 100 cubic meters of water.

Hydrostatic relation

Tonnes per centimetre immersion

$$\textcolor{#2a78d6}{\mathit{TPC}} = \frac{\textcolor{#eb6834}{A_{\mathrm{W}}}\,\textcolor{#1baf7a}{\rho}}{100}$$

where

\(\mathit{TPC}\)mass that changes the mean draft by 1 cmt/cm
\(A_{\mathrm{W}}\)waterplane area at the draftm²
\(\rho\)water densityt/m³

The tonnes per centimetre immersion of a wall-sided box is the same at every draft. A box 100 m long and 20 m wide has A_W = 2,000 m², so its TPC in salt water is 20.5 t/cm. On a real hull the waterplane grows with draft, so TPC grows too. TPC enters bodily sinkage, the fresh water allowance and the first trim correction of a draft survey.

Moment to change trim one centimetre

Moment to change trim one centimetre (MCT 1 cm) is the trimming moment, in tonne-meters, that changes the trim by 1 cm. A trimming moment Δ GM_L tan θ turns the ship through θ. A trim of 1 cm over length L is tan θ = 0.01 / L.

Hydrostatic relation

Moment to change trim one centimetre

$$\textcolor{#2a78d6}{\mathit{MCT}_{1\,\mathrm{cm}}} = \frac{\textcolor{#eb6834}{\Delta}\,\textcolor{#1baf7a}{\mathit{GM}_{\mathrm{L}}}}{100\,L}$$

where

\(\mathit{MCT}_{1\,\mathrm{cm}}\)trimming moment that changes the trim by 1 cmt·m/cm
\(\Delta\)displacementt
\(\mathit{GM}_{\mathrm{L}}\)longitudinal metacentric height; BM_L is the usual approximationm
\(L\)length between perpendicularsm

The ITTC 2024 list gives the symbol MTC with the SI unit N m/cm; hydrostatic tables print the practice unit t·m/cm. KG is small compared with BM_L, so GM_L is close to BM_L, and a table can compute MCT 1 cm from BM_L. For the example box at 6 m draft, the moment to change trim one centimetre is 12,300 × 138.9 / 10,000 = 170.8 t·m/cm. The change of trim from a weight w moved a distance d along the ship is w d / MCT 1 cm, in centimetres.

Center of buoyancy: KB and LCB

KB is the height of the center of buoyancy above the keel, and LCB is its longitudinal position; both are centroids of the displaced volume. The ITTC list defines KB as the “centre of buoyancy above molded base or keel”. For a box, KB is exactly half the draft. Where the waterplane widens with draft, KB lies above half the draft.

The LCB moves when the ship trims. A trim by the stern adds a wedge of volume aft and removes an equal wedge forward, and B moves aft with it. The ship comes to rest when the LCB and the LCG are at the same longitudinal position. The trim and list calculation solves that condition. An even-keel table gives the LCB for a level waterline only.

Center of flotation

The center of flotation F is the centroid of the waterplane area, and a ship trims about a transverse axis through F. The first moment of the waterplane about F is zero. So, for a small change of trim, the wedge added at one end equals the wedge lost at the other only about this axis.

The center of flotation has two practical uses. A mass loaded or discharged vertically above F changes the mean draft and leaves the trim unchanged. A change of trim divides between the ends in proportion to their distances from F, not equally. That second rule is why the first trim correction of a draft survey contains the LCF.

Metacentric radii: BM, BM_L and KM

The metacentric radius BM is the second moment of the waterplane area about its axis, divided by the displaced volume. The transverse radius uses the second moment about the centerline. The longitudinal radius uses the second moment about a transverse axis through F.

ITTC Symbols List 2024: BM = I_T / volume

Metacentric radii

$$\textcolor{#2a78d6}{\mathit{BM}} = \frac{\textcolor{#eb6834}{I_{\mathrm{T}}}}{\nabla} \qquad \mathit{BM}_{\mathrm{L}} = \frac{\textcolor{#1baf7a}{I_{\mathrm{L}}}}{\nabla}$$

where

\(\mathit{BM}\)transverse metacenter above the center of buoyancym
\(I_{\mathrm{T}}\)second moment of the waterplane area about the centerlinem⁴
\(I_{\mathrm{L}}\)second moment of the waterplane area about a transverse axis through the center of flotationm⁴
\(\mathit{BM}_{\mathrm{L}}\)longitudinal metacenter above the center of buoyancym
\(\nabla\)displaced volumem³

KM = KB + BM is the height of the transverse metacenter above the keel. The term is Pierre Bouguer’s, from Traité du navire (1746). Leonhard Euler reached the same stability theory independently in 1749. The metacentric height is GM = KM − KG. For ships of 24 m in length and over, the 2008 IS Code, Part A 2.2.4, sets the initial GM at not less than 0.15 m.

Figure 1 shows how KM varies with draft on the example box. For a box, BM = B² / 12T, so BM falls as the draft rises. KM is least at T = B / √6, which is 8.16 m for a 20 m beam. KM falls from 17.67 m at 2 m draft to that least value of 8.16 m, then rises again.

0481216200246810Height above keel (m)Draft T (m)least KM 8.16 m at T 8.16 mKM = KB + BMKB = T / 2BM = B² / 12TExample box barge L 100 m, B 20 m, salt water 1.025 t/m³
Figure 1. On a box barge, KB rises in a straight line with draft and BM = B² / 12T falls faster at small drafts, so KM falls to a least value and then rises. TPC is constant because the waterplane does not change.

BM_L for the same box is L² / 12T, or 138.9 m at 6 m draft. The box BM_L is therefore 1.39 times the length. For L/B of 5 to 7, BM_L is 25 to 50 times BMT. An error of a few centimeters in KG therefore has no practical effect on GM_L or on MCT 1 cm.

Form coefficients

The form coefficients are ratios of the hull’s areas and volume to the enclosing rectangles and box, and they summarize the hull shape. The ITTC 2024 list defines the block coefficient as CB = ∇ / (L B T). It defines the waterplane area coefficient as CWP = A_WP / (L B). The midship section coefficient CM is the immersed midship area over B T. The prismatic coefficient CP is the volume over the midship area times L.

The coefficients are related by CB = CP × CM. The waterplane coefficient is not part of that product. The naval architecture coefficients article gives the full set and their uses in hull form design.

The block coefficient also carries regulatory weight. The 1988 Load Lines Protocol, Regulation 3, takes CB at 85% of the least molded depth for the freeboard calculation. IACS UR S11 Rev.10 (December 2020) uses CB in the wave bending moment.

Wetted surface

The wetted surface is the area of the hull shell below the waterline, in m², and it sets the frictional resistance of the hull. A hydrostatic table can print it against draft. The wetted surface area article covers the formulas, and ship resistance and powering covers its use.

The hydrostatic table and the curves of form

A hydrostatic table lists the particulars against draft in fixed steps; the curves of form plot the same particulars against draft on one sheet. The 2008 IS Code, Part B 3.6.4.4, lists for the stability booklet “hydrostatic curves or tables and cross curves of stability calculated on a free-trimming basis, for the ranges of displacement and trim anticipated in normal operating conditions”.

Two points in that item go beyond a plain even-keel table. First, the data cover a range of trim, not only an even keel. Second, Part B 3.5.1 defines the free-trimming basis: the calculation takes “into account the change in trim due to heel”. A trimmed hull that heels also changes its trim, and a free-trim calculation lets it.

ECE/ENERGY/19 enters the table at the corrected mean draft and then applies trim corrections. The code allows approved trim-correction tables in place of its formulas.

The table states its reference plane. ECE/ENERGY/19 covers hydrostatic data calculated to the molded base. In that case the keel plate thickness is deducted from the corrected mean draft before the table is entered. The draft marks are the drafts the survey reads.

Computing the particulars from the lines plan

Hydrostatic particulars are integrals of the hull offsets: areas from half-breadths, volumes from areas, and centroids and second moments from moments of those areas. The offsets come from the ship lines plan, as half-breadths at stations and waterlines. A classical calculation integrates them station by station with Simpson’s rules.

The integrals for one waterline are:

  • waterplane area \( A_{\mathrm{W}} = 2\int y\,\mathrm{d}x \);
  • first moment about midships, for the LCF, \( 2\int x\,y\,\mathrm{d}x \);
  • transverse second moment \( I_{\mathrm{T}} = \tfrac{2}{3}\int y^{3}\,\mathrm{d}x \);
  • longitudinal second moment about midships \( 2\int x^{2}\,y\,\mathrm{d}x \), moved to F by the parallel axis rule;
  • section area at a station \( A(z) = 2\int y\,\mathrm{d}z \), from the keel to the waterline;
  • volume \( \nabla = \int A_{\mathrm{W}}\,\mathrm{d}z \) over the draft, or \( \int A\,\mathrm{d}x \) over the length.

Simpson’s first rule

Simpson’s first rule integrates an odd number of equally spaced ordinates with the multipliers 1, 4, 2, 4 and so on to 4, 1. The weighted sum is multiplied by one third of the spacing. The rule fits a parabola through each group of three ordinates. It is exact for any curve up to a cubic.

Simpson's first rule

Waterplane area from half-breadths

$$\textcolor{#2a78d6}{A_{\mathrm{W}}} = 2 \cdot \frac{\textcolor{#eb6834}{h}}{3}\left(y_0 + 4y_1 + 2y_2 + \dots + 4y_{n-1} + y_n\right)$$

where

\(A_{\mathrm{W}}\)waterplane area, both sidesm²
\(h\)station spacing; n intervals, n evenm
\(y_i\)half-breadth at station im

Figure 2 shows the rule on 11 half-breadths at 10 m spacing. The sum of products is 225.7, and the waterplane area is 1,505 m².

0.6014.6147.6229.2349.84210.0549.9629.4748.0825.2940.9101StationMultiplierHalf-breadths y (m) at 11 equally spaced stations, spacing h = 10 mSum of products 225.7; A = 2 x (h / 3) x 225.7 = 1,505 m². Example numbers.
Figure 2. Simpson's first rule weights the half-breadths at equally spaced stations by 1, 4, 2, 4 and so on, ending 4, 1. Twice h / 3 times the sum of products gives the waterplane area. The numbers are an example.

The same multipliers give the first moment if each product is multiplied by its lever from midships. They give I_T if the half-breadths are cubed first. A hydrostatic calculation does this at every waterline, and then integrates the waterplane areas vertically to get the volume.

Simpson’s second rule and the five-eight-minus-one rule

Simpson’s second rule integrates groups of three intervals with the multipliers 1, 3, 3, 1, times three eighths of the spacing. It fits a cubic through four ordinates. A curve with a multiple of three intervals takes the second rule. A curve with a number of intervals that is neither even nor a multiple of three takes a combination of both rules.

The five-eight-minus-one rule gives the area of one interval from three ordinates: \( \tfrac{h}{12}(5y_0 + 8y_1 - y_2) \). Naval architects use it for the first interval of a curve, or for a small area between two close ordinates.

Trapezoidal rule

The trapezoidal rule treats the curve as straight between ordinates. The area is the spacing times the sum of the ordinates, with the two end ordinates halved. In symbols, \( A = h\left(\tfrac{y_0}{2} + y_1 + \dots + \tfrac{y_n}{2}\right) \). It has no condition on the number of intervals. It suits a section with a knuckle, a chine or a flat side, where a parabola through three points would round off a corner. On a smooth curve with the same ordinates, Simpson’s first rule gives the smaller error.

Stations against a three-dimensional hull model

A hydrostatics program can integrate over the hull surface instead of over stations, by the divergence theorem. A volume integral of a vector field whose divergence is 1, for example \( \mathbf{F} = (0, 0, z) \), becomes a surface integral: \( \nabla = \oint z\, n_z\, \mathrm{d}S \) over the immersed hull and the waterplane. A divergence-free field integrates to zero, so the field has to have a divergence of 1.

A surface method evaluates any waterline, trimmed or heeled, without stations. It also handles bulbs, transoms and sponsons that a station calculation captures only with extra half-stations. The 2008 IS Code, Part B 4.1.6.2.3, asks for the stability instrument’s “main dimensions, hydrostatic particulars and, if applicable, the ship’s profile” as approval data. The method of calculation is the program’s choice. IACS UR L5 Rev.4 checks the results against the approved data within the Table 1 tolerances. A three-dimensional hull model of this kind is also the input to computational fluid dynamics in hull design.

Bonjean curves

Bonjean curves are a set of curves, one at each transverse station, that plot the immersed area of the section against draft. The rate at which the area grows with draft is the full breadth of the section at that waterline, \( \mathrm{d}A/\mathrm{d}z = b(z) \). With draft on the vertical axis, as drawn, the plotted slope is \( 1/b \).

Constructing Bonjean curves

Each Bonjean curve is the running integral of the section breadth from the keel up to each waterline. At one station, the half-breadths at each waterline are integrated upward, by Simpson’s rules or the trapezoidal rule. The result is a list of area against draft for that station. The curves are drawn on the ship profile, each from its own station line, to a common area scale.

The curves do not depend on trim. They describe the hull shape only. The waterline is drawn on the same profile afterward, so one set of curves serves every waterline the ship can float at.

Reading a trimmed waterline

On a trimmed waterline the draft differs at every station, and the Bonjean curves give the immersed area at each of those drafts. Figure 3 shows a waterline at 8.4 m aft and 6.0 m forward crossing 11 stations.

012345678910APFPTrimmed waterline: 8.4 m aft, 6.0 m forwardBonjean curve: area against draftOrange bar: immersed area read at each station. Example hull, not a real ship.Stations
Figure 3. A Bonjean curve at each station plots immersed area against draft. A trimmed waterline crosses each station at its own draft, and the area read there is the horizontal distance to the curve. Integrated along the length, the areas give volume and LCB.

The procedure for one waterline is:

  1. Draw the waterline on the profile from the drafts at the perpendiculars.
  2. At each station, read the draft where the waterline crosses the station.
  3. Read the immersed area from that station’s curve at that draft.
  4. Integrate the areas along the length by Simpson’s first rule. The result is the volume.
  5. Integrate the areas times their levers from midships. Divide by the volume. The result is the LCB.

The method is valid for any straight waterline within the range of the curves. It does not need the trim to be small. A hogged or sagged hull has a curved keel, so the station drafts no longer lie on a straight line.

Figure 4 shows the curves of Figure 3 read at even keel and trimmed by the stern, at the same mean draft of 7.2 m. Trim by the stern increases the areas at the aft stations and reduces them at the forward stations. On the example hull, the volume changes by less than 0.5%, but the LCB moves aft.

Even keel7.2 m at every stationAPFPImmersed area by stationmidshipsLCBTrimmed by the stern8.4 m aft, 6.0 m forwardAPFPImmersed area by stationmidshipsLCB
Figure 4. The same Bonjean curves serve both waterlines. Trim by the stern moves immersed area from the forward stations to the aft stations, so the LCB moves aft while the volume hardly changes. The hull is the example of Figure 3.

Hogged and sagged waterlines

A deflected hull is handled by correcting each station draft for the deflection and then reading the Bonjean curves at the corrected drafts. ECE/ENERGY/19, method (c), describes exactly that. By prior agreement, displacement is “calculated by integration of the transverse section areas representing the immersed portion of the hull as actually trimmed and deflected”.

The code distributes the deflection measured amidships with Table I. Figure 5 shows the shares: 1.00 at the perpendiculars, falling as a parabola to zero amidships.

WaterlineStraight line through the midship draftHogged keelAP1.0010.6420.3630.1640.0450.0060.0470.1680.3690.64FP1.00StationShareECE/ENERGY/19 Table I: share of the midship deflection added to each station draftCorrection + for hog, - for sag. Deflection exaggerated. Not a real ship.
Figure 5. ECE/ENERGY/19 spreads the deflection measured amidships along the hull as a parabola. Each station's share is applied to the draft taken from a straight trimmed line through amidships, plus for hog and minus for sag. The deflection is exaggerated.

Table I applies its share to “the draught taken from a trimmed straight line through amidship”, with the correction plus for hog and minus for sag. The hogging and sagging of a loaded hull is the still-water deflection that this corrects. The same deflection shows as the difference between the midship draft and the mean of the end drafts.

Buoyancy distribution and longitudinal strength

The Bonjean areas at the actual waterline, times the density and g, give the buoyancy per unit length along the hull. That buoyancy curve is one of the two curves in a still-water strength calculation. The other is the weight per unit length. Their difference is the net load. Integrating the load once gives the shear force, and integrating again gives the bending moment.

The still-water bending moment and shear force that result are checked against the permissible values in the loading manual. IACS UR S1 Rev.7 (May 2010) applies to classed sea-going ships of 65 m and above contracted on or after 1 July 1998. Under S1.2.1 every such ship carries a loading manual, with one exemption. The exemption covers Category II ships under 90 m whose deadweight does not exceed 30% of the summer load line displacement. Its preamble states that it “satisfies Regulation 10(1)” of the International Convention on Load Lines, 1966.

UR S1 also requires a loading instrument on Category I ships of 100 m and above. SOLAS Chapter XII, as revised by MSC.170(79), makes the loading instrument statutory on bulk carriers. Regulation 11.1 applies to bulk carriers of 150 m and upwards. The IACS UR S-series on hull strength sets the rest of the chain. UR S11 Rev.10 sizes the hull girder section modulus for the still-water and wave moments together. The hull strength and longitudinal bending article covers the theory.

Damaged and flooded conditions

After flooding, the Bonjean areas of the intact part of each section give the buoyancy that remains. The equilibrium waterline is the one at which that buoyancy supports the ship. A flooded compartment contributes its section areas times the permeability as lost buoyancy, or as added weight in the other method. The damage stability article covers both methods and the criteria.

The same section areas give the floodable length curve of the deterministic subdivision method. The probabilistic damage stability method of SOLAS II-1 Part B-1 evaluates each damage case on its own flooded waterline.

Hydrostatic tables in draft surveys

A draft survey finds the mass of cargo from the change in displacement, read from the hydrostatic tables, between two surveys. ECE/ENERGY/19, the “Code of Uniform Standards and Procedures for the Performance of Draught Surveys of Coal Cargoes”, sets the procedure. The UNECE Working Party on Coal adopted it in October 1991, and the Committee on Energy endorsed it in November 1991.

The code is a recommendation, not a convention. Its background calls it “a set of recommendations which may be applied in full or in part by parties in international coal trade”. The UN/ECE draft survey code article covers its scope. The draft survey for bulk cargo article gives the full method.

Mean of means of means draft

The mean of means of means (M/M/M) draft combines the forward, after and midship drafts into one mean that allows for hog or sag. ECE/ENERGY/19 calls it “an approximate method of correcting the calculated displacement for the effect of hull deflection”.

The code builds it in three steps. M is the mean of the drafts at the forward and after perpendiculars. M/M is the mean of M and the midship draft MS. M/M/M is the mean of M/M and MS. The three steps combine into one expression.

ECE/ENERGY/19, lines 151 to 152

Mean of means of means draft

$$\textcolor{#2a78d6}{\mathit{M/M/M}} = \frac{\textcolor{#eb6834}{D_{\mathrm{FP}}} + \textcolor{#eb6834}{D_{\mathrm{AP}}} + 6\,\textcolor{#1baf7a}{\mathit{MS}}}{8}$$

where

\(\mathit{M/M/M}\)mean draft corrected for hull deflection, entered in the hydrostatic tablem
\(D_{\mathrm{FP}},\ D_{\mathrm{AP}}\)port and starboard mean drafts at the forward and after perpendicularsm
\(\mathit{MS}\)port and starboard mean draft amidshipsm

The midship draft carries six eighths of the weight. Hog or sag, in the code, is MS minus M: a plus value means the ship has sag and a minus value means hog. The code then enters the hydrostatic table at the M/M/M draft “by means of linear interpolation”. A surveyor first corrects each reading to its perpendicular, which the true mean draft article covers.

First and second trim corrections

The first trim correction allows for the LCF not being amidships, and the second (Nemoto) correction is a small additional term that is always positive. ECE/ENERGY/19 prints both. Together they move the even-keel displacement to the trimmed waterline.

ECE/ENERGY/19, lines 162 to 164

First and second trim corrections

$$\textcolor{#2a78d6}{C_1} = \frac{\mathit{TPC}\times \mathit{LCF}\times t \times 100}{L} \qquad \textcolor{#eb6834}{C_2} = \frac{50\,t^{2}\,\textcolor{#1baf7a}{(\mathrm{d}M/\mathrm{d}Z)}}{L}$$

where

\(C_1\)first trim correction; sign from the ECE table of trim and LCF positiont
\(C_2\)second (Nemoto) trim correction, always addedt
\(\mathrm{d}M/\mathrm{d}Z\)difference in MCT 1 cm between drafts 50 cm above and 50 cm below the mean draftt·m/cm
\(\mathit{TPC}\)tonnes per centimetre immersion at the corrected mean draftt/cm
\(\mathit{LCF}\)center of flotation from midshipsm
\(t\)trim between the perpendicularsm
\(L\)length between perpendicularsm

The sign of the first correction depends on the trim and on the side of midships where the LCF lies. Under the code, a trim by the stern with the LCF aft gives a plus correction. With the LCF forward the correction is minus. A trim by the head reverses both. The code says “The Nemoto Correction is always +”. The draft survey trim corrections article covers the derivation.

The following worked example uses illustrative values for a 180 m ship. It is not a real survey.

  1. Read the drafts and correct them to the perpendiculars and amidships: D_FP 9.80 m, D_AP 10.40 m, MS 10.15 m.
  2. Compute M = 10.10 m, M/M = 10.125 m and M/M/M = 10.1375 m. MS minus M is +0.05 m, so the ship has sag.
  3. Enter the table at 10.1375 m. Take Δ₁ = 50,000.0 t, TPC 52.0 t/cm, LCF 3.20 m aft of midships.
  4. Compute the trim: 10.40 − 9.80 = 0.60 m by the stern.
  5. Compute the first correction: 52.0 × 3.20 × 0.60 × 100 / 180 = 55.5 t, plus.
  6. Compute the Nemoto correction with an MCT difference of 15.0 t·m/cm: 50 × 0.36 × 15.0 / 180 = 1.5 t, plus.
  7. Add both corrections: Δ₂ = 50,057.0 t.

Draft survey density correction

The density correction scales the trim-corrected displacement from the reference density of the tables to the density measured at the ship. ECE/ENERGY/19 gives it as the difference of the two densities over the reference density, times the displacement. The code’s form labels the displacement as line 161, but line 166 applies the correction to Displacement (2), after the trim corrections.

ECE/ENERGY/19, line 167

Density correction

$$\textcolor{#2a78d6}{C_{\rho}} = \frac{\textcolor{#eb6834}{\rho_{\mathrm{R}}} - \textcolor{#1baf7a}{\rho_{\mathrm{M}}}}{\rho_{\mathrm{R}}}\,\Delta_2$$

where

\(C_{\rho}\)correction subtracted from the trim-corrected displacementt
\(\rho_{\mathrm{R}}\)reference density of the hydrostatic datat/m³
\(\rho_{\mathrm{M}}\)measured density of the water at the shipt/m³
\(\Delta_2\)displacement after the trim correctionst

The code states that “if the measured density is less than the reference density, the density correction is minus”. In the worked example, a measured density of 1.018 t/m³ against 1.025 gives a correction of 341.9 t, minus. The displacement in the dock water is therefore 49,715.1 t. The cargo figure is the difference between two such displacements, after the ship’s constant and the deductibles.

The code asks for a hydrometer “calibrated to read weight per unit volume in air”. It asks for samples amidships near the surface and near the bottom of the keel, then at the bow and stern if they differ. The density used is the average of all readings.

Hull deflection by the waterplane method

ECE/ENERGY/19 method (d) corrects for deflection with a factor taken from the waterplane coefficient, in place of the M/M/M mean. For a hogged ship, the deflected draft is M − f (M − MS); for a sagged ship it is M + f (MS − M). The factor f comes from Table II of the code, plotted against the waterplane coefficient worked out from TPC, LBP and B.

The M/M/M mean gives the deflection a fixed share of 75% on M, while the Table II factor changes with the waterplane coefficient. The code also allows, under method (b), an approved hull deflection table for the ship in place of method (a).

Bodily sinkage, density and trim from the hydrostatic table

A hydrostatic table gives the sinkage for a load, the sinkage or rise for a change of density, and the trim for a shift of weight. Each answer uses one particular from the table at the current draft.

Bodily sinkage

Bodily sinkage is the change in mean draft when a mass is loaded or discharged at the center of flotation, equal to the mass divided by TPC.

Hydrostatic relation

Bodily sinkage

$$\textcolor{#2a78d6}{\delta T} = \frac{\textcolor{#eb6834}{w}}{\textcolor{#1baf7a}{\mathit{TPC}}}$$

where

\(\delta T\)change in mean draftcm
\(w\)mass loaded or discharged at the center of flotationt
\(\mathit{TPC}\)tonnes per centimetre immersion at the initial draftt/cm

The rule holds while the waterplane is nearly constant over the change in draft and the mass acts at F. A 1,000 t parcel on a ship with a TPC of 52.0 t/cm changes the mean draft by 19.2 cm. For a large change, the displacement at both drafts is read from the table instead. Loading away from F also trims the ship, by w d / MCT 1 cm. Squat is a different effect: a sinkage from the flow around a ship under way, not a change of displacement.

Fresh water allowance and dock water

The fresh water allowance is the amount by which the summer load line can be submerged when a ship loads in fresh water. Regulation 40(7) of the 1988 Load Lines Protocol gives it from displacement and TPC. The text, as amended by MSC.143(77), reads: “The minimum freeboard in fresh water of unit density shall be obtained by deducting from the minimum freeboard in salt water: Δ/(40T) (cm)”. In that formula Δ is the salt-water displacement at the summer load waterline, and T is the TPC in salt water there.

1988 LL Protocol, Annex B, Reg 40(7)

Fresh water allowance

$$\textcolor{#2a78d6}{\mathit{FWA}} = \frac{\textcolor{#eb6834}{\Delta}}{40\,\textcolor{#1baf7a}{T}}$$

where

\(\mathit{FWA}\)deduction from the salt-water freeboard for fresh water of unit densitycm
\(\Delta\)displacement in salt water at the summer load waterlinet
\(T\)tonnes per centimetre immersion in salt water at the summer load waterlinet/cm

The formula is exact for a wall-sided hull near the load waterline. The extra volume in fresh water is Δ (1/1.000 − 1/1.025). Spread over A_W = 100 TPC / 1.025, that volume gives Δ × 0.025 / TPC centimeters, which is Δ / (40 TPC). If 6 m were the summer draft of the example box, the fresh water allowance is 12,300 / (40 × 20.5) = 15.0 cm.

Regulation 40(8) covers ships whose displacement “cannot be certified”. The deduction is then “one forty-eight of summer draught”. The summer draft is measured from the top of the keel to the center of the ring of the load line mark. Regulation 6(e) marks the result on the ship. The Fresh Water Load Line in summer, less the Summer Load Line, “is the allowance to be made for loading in fresh water at the other load lines”.

The dock water allowance applies the same idea to water of intermediate density: DWA = FWA × (1.025 − ρ) / 0.025. That expression is a derivation from Regulation 40(7), not a formula the Protocol prints. TPC scales with the density itself: in fresh water, TPC is the salt-water value times 1.000 / 1.025.

Trim and the center of flotation

A change of trim divides between the ends of the ship in proportion to their distances from the center of flotation. Let F be a distance x_F forward of the after perpendicular. The change of draft aft is then the change of trim times x_F / L, and the change forward is the remainder. Where F is aft of midships, the after draft changes less than the forward draft.

This is why the after and forward drafts in a loading plan do not move equally for a weight added at midships. The trim optimization of a ship in service starts from the same tables at the operating drafts.

Hydrostatic data in the stability booklet and the loading instrument

SOLAS II-1/5-1 requires stability information for the master of a passenger ship or a cargo ship other than a tanker. The 2008 IS Code, Part B, lists hydrostatic curves or tables in that information. MSC.421(98), Reg 4.2.1.1, limits regulation 5-1 for cargo ships to “cargo ships other than tankers”. The text of Reg 5-1.1, as replaced by MSC.421(98), is: “The master shall be supplied with such information to the satisfaction of the Administration as is necessary to enable him by rapid and simple processes to obtain accurate guidance as to the stability of the ship under varying conditions of service.”

MSC.421(98) was adopted on 15 June 2017 and entered into force on 1 January 2020. Its new Reg II-1/1.1.1 applies the 2020 text to a ship that meets one of three dates:

  • building contract on or after 1 January 2020;
  • keel laid on or after 1 July 2020;
  • delivery on or after 1 January 2024.

For those ships, MSC.421(98) changed Reg 5-1 in two ways that affect hydrostatic data:

  • Reg 5-1.2.1 now asks for curves or tables of minimum operational GM “and maximum permissible trim versus draught”, or the equivalent KG curves.
  • Reg 5-1.3 now requires the information to be “presented as consolidated data and encompass the full operating range of draught and trim”. Ships constructed from 1 January 2009 up to those dates keep the MSC.216(82) text. That text asks for trim effects only where the operating trim range exceeds ±0.5% of Ls.

Reg 5-1 does not name hydrostatic tables and does not require a loading manual. The hydrostatic tables enter through the 2008 IS Code, Part B 3.6.4.4, and through Reg 5-1.2.3, “all other data and aids which might be necessary”. The stability booklet, loading manual and loading computer article covers the whole booklet.

The loading manual is a separate document. The 1988 Load Lines Protocol, Regulation 10(1), requires information on loading and ballasting. Its purpose is to load the ship “in such a way as to avoid the creation of any unacceptable stresses in the ship’s structure”. Regulation 10(2) requires it to be approved and carried “at all times”. IACS UR S1 Rev.7 is the class requirement that implements it.

The loading instrument holds the hydrostatics as data or as a hull model. The 2008 IS Code, Part B 4.1.6.2.3, lists “Main dimensions, hydrostatic particulars and, if applicable, the ship’s profile” among the approval data. IACS UR S1.2.3 refers to IACS Recommendation 48 for loading instruments. IACS UR L5 Rev.4 states: “The use of onboard computers for stability calculations is not a requirement of class.” It sets the tolerances in the table above where a program is fitted.

The inclining test also starts from the hydrostatic data. The 2008 IS Code, Part B 8.3.2, lists “hydrostatic curves or hydrostatic data” among the plans needed at the test. Part B 8.2.2.7 adds a check on the data. “In order to avoid excessive errors caused by significant changes in the water plane area during heeling, hydrostatic data for the actual trim and the maximum anticipated heeling angles should be checked beforehand.”

Regulatory basis of hydrostatic data

No IMO instrument prints a hydrostatic table. Five instruments and two IACS requirements govern what the data contain, who approves them and how they are used on board. The table below lists them with the clause that names the data.

InstrumentClauseWhat it says about hydrostatic data
2008 IS Code, MSC.267(85), Part B3.5.1Free-trim calculation; deck sheathing, appendages and sea chests included
2008 IS Code, Part B3.6.4.4Booklet to include hydrostatic curves or tables on a free-trimming basis
2008 IS Code, Part B4.1.6.2.3Stability instrument approval data include hydrostatic particulars
SOLAS II-1/5-1, MSC.421(98) text5-1.1 to 5-1.3Stability information to the master, consolidated over the full draft and trim range (2020 text ships)
SOLAS II-1/5-1, MSC.216(82) text5-1.3Trim effects where the operating trim range exceeds ±0.5% of Ls (ships built 2009 to 2019)
SOLAS XII, MSC.170(79)Reg 11.1Loading instrument on bulk carriers of 150 m and upwards
1988 LL Protocol, Annex B, MSC.143(77)Reg 10, Reg 40(7) and (8)Loading information approved and on board; fresh water deduction from Δ and TPC
IACS UR S1 Rev.7 (May 2010)S1.1, S1.2Loading manual for ships of 65 m and above, with the S1.2.1 exemption; instrument for Category I of 100 m and above
IACS UR L5 Rev.4 (June 2020)Table 1Tolerances on displacement, LCB, LCF, KB, MCT 1 cm, GM and drafts
ECE/ENERGY/19 (1991)Lines 151 to 168Draft survey: M/M/M, trim and density corrections, recommendation only

The 2008 IS Code became mandatory, for Part A, on 1 July 2010 through amendments to SOLAS Chapter II-1 and the 1988 Load Lines Protocol. Oil tankers of 5,000 tonnes deadweight and above delivered on or after 1 February 2002 add the intact stability rule of MARPOL Annex I Reg.27. Ships carrying grain add the International Grain Code. Each criterion is evaluated from the hydrostatic and cross-curve data of the ship.

The classification society approves the loading manual under UR S1 and the stability software under UR L5. The 2008 IS Code, Part B 3.6.2, names the Administration as the body that approves the stability booklet. The load line certificate and surveys article covers the freeboard survey, at which the marks of Regulation 6 are checked.

Stability calculations that start from hydrostatic data

The hydrostatic data at the upright waterline are the start of every stability calculation, and each later step has its own article. The pointers below give the link and the one fact that ties each step to this article.

  • Cross curves of stability and KN tables: KN against displacement at fixed heel angles, on the free-trim basis of Part B 3.5.1.
  • GZ curve and righting arm: GZ = KN − KG sin φ, read at the displacement from the hydrostatic table.
  • Righting moment: Δ × GZ, with Δ from the table.
  • Wall-sided formula: GZ from GM and BM at moderate heel, with BM from the table.
  • Free surface effect: the virtual rise of G from slack tanks, which reduces the GM found from KM.
  • Inclining experiment: KM from the hydrostatic table at the test displacement, minus GM from the test, gives KG.
  • Deadweight survey: a lightship check by drafts and the hydrostatic table.
  • Lightweight calculation and weight control: the record that keeps lightship changes within the limits that keep the hydrostatic and stability data valid.

Limitations

The figures in this article are illustrations of the method, and none of them is a value for a real ship. The box barge of Figure 1 and the 180 m ship of the draft survey example are examples. A real ship’s particulars come only from its approved hydrostatic data.

The article does not reproduce the full text of ECE/ENERGY/19. Its Table II factors are read from a chart, and this article gives the method, not the values. The code is written for coal cargoes and is a recommendation; a charter party or a sale contract decides which survey standard applies.

The 2008 IS Code, Part B, is recommendatory. An Administration can adopt it with changes. The trim and stability information that SOLAS II-1/5-1 requires depends on the text that applies to the ship. That text follows from the contract, keel and delivery dates. National rules are outside the scope of this article.

The formulas for TPC, MCT 1 cm, bodily sinkage and the dock water allowance are standard derivations. No IMO instrument prints them. Each one assumes small changes in draft or trim; outside that range, read the table directly.

Frequently Asked Questions (FAQs)

What is the difference between a hydrostatic table and the curves of form?

They hold the same data in two forms.

The hydrostatic table lists each particular, such as displacement, TPC, MCT 1 cm, KB, LCB, LCF and KM, against draft at fixed steps. The curves of form plot the same particulars against draft on one sheet, each to its own scale. A table is read by interpolation and suits a draft survey; curves show at a glance how a particular changes with draft. The 2008 IS Code, Part B 3.6.4.4, accepts either: hydrostatic curves or tables.

Which water density does a hydrostatic table assume?

The table assumes the reference density printed in the ship’s own hydrostatic data, which for salt-water data is 1.025 t/m3, the Regulation 27 value.

The 1988 Load Lines Protocol uses 1.025 for salt water in its damage assumptions. Its Reg 40(7) gives the fresh water freeboard for water of unit density. A draft survey uses the reference density from the data, called RD in ECE/ENERGY/19, and corrects the displacement for the density measured at the ship.

Is the tabulated displacement molded or extreme?

It depends on the data, and the table states which.

ECE/ENERGY/19 covers hydrostatic data to the molded base: the keel plate thickness is then deducted from the corrected mean draft before the table is entered. The 2008 IS Code, Part B 3.5.1, asks for volume to the upper surface of the deck sheathing. It also asks for appendages and sea chests to be considered, so an approved table includes more than the molded hull.

Why does an even-keel hydrostatic table still need trim corrections?

An even-keel table gives the displacement for a level waterline at the tabulated draft.

A trimmed ship floats on a waterline that crosses the hull at different drafts. Its center of flotation is not amidships, so the mean draft does not give the correct displacement. ECE/ENERGY/19 applies a first trim correction, TPC x LCF x trim x 100 / LBP, and a second (Nemoto) correction.

How do you interpolate between two rows of a hydrostatic table?

Use linear interpolation between the two rows that bracket the draft.

ECE/ENERGY/19 tells the surveyor to extract the displacement from the approved hydrostatic tables for the corrected mean draft by linear interpolation. Displacement at the lower row plus TPC times the difference in centimeters gives nearly the same result. That holds while TPC changes little over the step. ECE/ENERGY/19 prints this form for hydrostatic curves: D(1) = DC + TPC x (CD minus M/M/M).

Why does TPC increase with draft on most hulls?

TPC is proportional to the waterplane area, and on a ship-shaped hull the waterplane grows with draft as the ends and the bilge fill out.

A wall-sided box keeps the same waterplane at every draft, so its TPC is constant: 20.5 t/cm for a 100 m by 20 m box in salt water. A real hull has a smaller waterplane near the keel and a larger one near the load waterline.

Is the bodily sinkage rule valid for a large weight change?

Only while the waterplane area stays nearly constant over the change in draft.

Sinkage equals the mass divided by TPC, and TPC itself changes with draft. For a large change, read the displacement directly from the table at the start and the end. The mass also has to act at the center of flotation, or the ship trims as well as sinks.

Why is BML so much larger than BMT?

BM is the second moment of the waterplane divided by the displaced volume, and the waterplane is much longer than it is wide.

For a box, BMT is B squared over 12T and BML is L squared over 12T. For L/B of 5 to 7, BML is 25 to 50 times BMT. For L/T of 12 to 24, BML of a box is one to two ship lengths.

Why does KM fall as draft increases and then rise again?

KM is KB plus BM. KB rises with draft, but BM is the waterplane second moment divided by the volume.

On a wall-sided hull the volume grows while the second moment stays the same. At small drafts BM falls faster than KB rises, so KM falls. On a box, KM is least at a draft of B divided by the square root of 6, and above that draft KM rises.

Which point does a ship trim about, the LCF or the LCB?

A ship trims about the center of flotation, the centroid of its waterplane.

A small change of trim adds a wedge of buoyancy at one end and removes an equal wedge at the other. The two wedges are equal only about an axis through the centroid of the waterplane. The LCB moves as the ship trims; the LCF is the pivot.

Why does the LCB move when a ship trims?

The LCB is the centroid of the underwater volume, and trim moves volume from one end to the other.

When the ship trims by the stern, a wedge of volume is added aft and an equal wedge is lost forward, so the center of buoyancy moves aft. Equilibrium returns when the LCB and the LCG are at the same longitudinal position.

How many stations does a hydrostatic calculation use?

No IMO instrument or IACS requirement sets a number of stations.

Simpson’s first rule needs an even number of intervals. ECE/ENERGY/19 Table I uses ten intervals, stations 0 to 10, with half-stations next to both perpendiculars. A program that integrates over the hull surface has no stations.

Why does Simpson's first rule use an odd number of ordinates?

The first rule fits a parabola through each group of three ordinates, so the intervals are taken in pairs.

An even number of intervals means an odd number of ordinates, with the multipliers 1, 4, 2, 4 and so on to 4, 1. Where the count does not fit, the second rule or the five-eight-minus-one rule completes the integration.

What is the five-eight-minus-one rule?

It gives the area between the first two of three equally spaced ordinates.

The area equals h divided by 12, times 5 times the first ordinate plus 8 times the second minus the third. It is used where Simpson’s rules leave one interval over.

When is the trapezoidal rule preferred to Simpson's rules?

The trapezoidal rule suits a curve with a kink or a straight segment, such as a knuckle, a chine or a flat of side.

The rule treats the curve as straight between ordinates. Simpson’s rules fit parabolas and give a smaller error on a smooth curve with the same ordinates. Simpson’s rules are exact for any curve up to a cubic.

Do Bonjean curves work on a hull with a bulbous bow or a transom stern?

Yes, because each curve is the area of the actual section at that station, whatever its shape.

The difficulty is the stations themselves. A bulb or an immersed transom changes shape fast along the length, so a calculation adds stations there or integrates over the hull surface instead of over stations.

Do Bonjean curves still matter when a loading computer holds a hull model?

Yes. A loading program needs the immersed section areas along the hull at any waterline, which is what Bonjean curves hold.

The 2008 IS Code, Part B 4.1.6.2.3, lists main dimensions and hydrostatic particulars among the approval data for a stability instrument. IACS UR L5 Rev.4 tests the program output against the approved hydrostatics.

Why does a surveyor read six drafts in a draft survey?

Six readings, port and starboard at the forward, midship and after marks, give the mean draft at each mark, the trim and the hull deflection.

ECE/ENERGY/19 corrects the drafts to the perpendiculars and amidships. The code then combines them into the mean of means of means draft, which allows for hog or sag.

When is the second trim correction large enough to matter?

The Nemoto correction grows with the square of the trim, so it matters most for large trim.

The correction is 50 times the trim squared times the MCT 1 cm difference, divided by LBP. On a 180 m ship with 0.60 m of trim and an MCT difference of 15 t·m/cm, the correction is 1.5 t. At 3 m of trim the same ship gives 37.5 t. ECE/ENERGY/19 says the Nemoto correction is always added.

How much cargo does a 1 cm draft error represent?

One centimeter of mean draft equals one TPC of displacement.

On a ship with a TPC of 52 t/cm, a 1 cm error in the corrected mean draft is a 52 t error in the cargo figure. ECE/ENERGY/19 corrects the drafts to the perpendiculars and amidships before the table is entered.

What is the dock water allowance?

The dock water allowance is the amount a ship can submerge its load line when it loads in water lighter than salt water and heavier than fresh water.

The allowance equals the fresh water allowance times (1.025 minus the dock water density) divided by 0.025. The expression is a derivation from Reg 40(7) of the 1988 Load Lines Protocol, not a formula that the Protocol prints.

What if the summer displacement cannot be certified for the fresh water allowance?

Reg 40(8) of the 1988 Load Lines Protocol, as amended by MSC.143(77), then sets the deduction at one forty-eighth of the summer draft.

The summer draft is measured from the top of the keel to the center of the ring of the load line mark. Where the displacement is known, Reg 40(7) uses displacement divided by 40 times TPC.

Does list change the hydrostatic table reading in a draft survey?

The port and starboard readings at each mark are averaged, which removes the effect of a small list on the mean draft.

A large list changes the waterplane, so the even-keel table no longer describes the waterline. The 2008 IS Code makes a similar point for the inclining test. Part B 8.2.2.7 asks for hydrostatic data at the actual trim and heel to be checked beforehand.

Who approves the hydrostatic data printed in the stability booklet?

The Administration approves the stability booklet that holds the hydrostatic data.

The 2008 IS Code, Part B 3.6.2, says each ship should have a stability booklet approved by the Administration. Under IACS UR S1 Rev.7 the classification society approves the loading manual, which carries the strength data.

When is hydrostatic data recalculated after a conversion?

When the alteration changes the underwater hull or the main dimensions, for example a lengthening, a new bulb or added sponsons.

The hull form then differs from the form the data describe, so new data follow as a matter of geometry. IACS UR L5 Rev.4 states that after changes to the main data, the specific approval of the onboard stability software is no longer valid. Weight changes alone alter the lightship, not the hydrostatics.

Does SOLAS still allow trim to be ignored below 0.5% of the length?

Not for ships under the 2020 text, but yes for ships built from 2009 to 2019.

The MSC.216(82) text of SOLAS II-1/5-1.3 asks for the influence of trim only where the operating trim range exceeds plus or minus 0.5% of Ls. MSC.421(98) replaced it with consolidated data over the full range of draft and trim. Under the new Reg II-1/1.1.1, the new text applies to ships contracted from 1 January 2020. It also applies to ships laid down from 1 July 2020 or delivered from 1 January 2024.

Which ships does SOLAS II-1/5-1 apply to?

SOLAS II-1/5-1 applies to passenger ships and to cargo ships other than tankers.

MSC.421(98), Reg 4.2.1.1, states that regulation 5-1 applies to cargo ships other than tankers as defined in SOLAS regulation I/2(h). Oil tankers take their intact stability requirement from MARPOL Annex I Regulation 27.

Is the LCF in the draft survey trim correction measured from midships or from the after perpendicular?

The first trim correction of ECE/ENERGY/19 uses the LCF from midships, as its sign table shows.

A hydrostatic table can give the LCF from the after perpendicular, the reference used in IACS UR L5 Rev.4 Table 1. A value from the after perpendicular has to be converted to a distance from midships before it goes into TPC x LCF x trim x 100 / LBP.

Is the block coefficient the product of the prismatic, midship and waterplane coefficients?

No. The block coefficient equals the prismatic coefficient times the midship section coefficient: CB = CP x CM.

The waterplane coefficient does not enter the product. The ITTC Symbols and Terminology List defines CB as volume over L x B x T and CWP as waterplane area over L x B.

How does TPC change in fresh water?

TPC is proportional to the water density.

In fresh water, TPC is the salt-water value times 1.000 / 1.025. A ship with a TPC of 52.0 t/cm in salt water has about 50.7 t/cm in fresh water at the same draft. The waterplane area is the same; only the mass of a 1 cm layer changes.

Sources

  1. IMO Resolution MSC.267(85). International Code on Intact Stability, 2008, Part B 3.5.1 and 3.6.4 imo.org
  2. IMO Resolution MSC.421(98). Amendments to SOLAS chapter II-1, regulation 5-1 stability information imo.org
  3. IMO Resolution MSC.143(77). Amendments to the 1988 Load Lines Protocol, Annex B, regulations 6, 10 and 40 imo.org
  4. IMO Resolution MSC.216(82). Revised SOLAS chapter II-1 Parts A, B and B-1, regulation 5-1 (text for ships built 2009 to 2019) imo.org
  5. IMO Resolution MSC.170(79). Revised SOLAS chapter XII on bulk carriers, regulation 11 loading instrument imo.org
  6. IACS UR S1 Rev.7 (May 2010). Requirements for Loading Conditions, Loading Manuals and Loading Instruments iacs.org.uk
  7. IACS UR L5 Rev.4 (June 2020). Computer Software for Onboard Stability Calculations iacs.s3.af-south-1.amazonaws.com
  8. UNECE ECE/ENERGY/19. Code of Uniform Standards and Procedures for the Performance of Draught Surveys of Coal Cargoes, archived copy web.archive.org
  9. ITTC Symbols and Terminology List, Version 2024. alphabetic list ittc.info