IACS Common Structural Rules for Bulk Carriers and Tankers
IACS Common Structural Rules for bulk carriers and oil tankers: scope, Parts 1 and 2, the net scantling approach, revisions and the IMO goal-based check.
Contents15 sections
The IACS Common Structural Rules (CSR BC&OT) are the classification rules for the hull structure of bulk carriers and double hull oil tankers. The rules apply to ships contracted on or after 1 July 2015. The thresholds are a freeboard length LLL of 90 m or above for bulk carriers and 150 m or above for oil tankers.
The International Association of Classification Societies publishes the CSR, and each member society applies them within its own rules. The current text is the 01 JAN 2024 rules with 01 JUL 2025 Corrigenda. This article is the hub for the CSR. The load, strength, buckling, fatigue and corrosion methods are in the spoke articles that the method map lists.
What the CSR are
The CSR are one set of hull structural rules, written jointly by the IACS members and applied by each member as its own class rules. The Foreword states: “Part One provides requirements common to both Double Hull Oil Tankers and Bulk Carriers and Part Two provides additional requirements applied to either Double Hull Oil Tankers or Bulk Carriers.”
Before the CSR, each classification society set its own scantling rules for these ships. The CSR replaced those rules with one text for the two ship types. A ship that fully complies receives the notation CSR (Pt 1 Ch 1 Sec 1 [3.1.1]).
Each society publishes the CSR in its own rule book. ClassNK, for example, incorporated them as “Part CSR-B&T” of its Rules for the Survey and Construction of Steel Ships (ClassNK amendment outline 15-1-04e). The Disclaimer states: “Copyright in these Common Structural Rules is owned by each IACS Member as at 1st July 2012.”
Class rules, not IMO law
The CSR are class rules, not an IMO convention. The IMO sets goals for hull structure in the goal-based ship construction standards, MSC.287(87). SOLAS regulation II-1/3-10 then requires ships to be built to the rules of a recognized organization that conform to those standards.
MSC.287(87) Tier III states: “The final decision on verification of conformity shall be taken by the Maritime Safety Committee of the Organization which shall inform all Contracting Governments of the decision.” The IMO checks the CSR; it does not write them. The IMO verification section covers the audits.
The CSR also do not cover survey. Pt 1 Ch 1 Sec 2 [2.2.2] states that the Rules “address the hull structural aspects of classification and do not include requirements related to the verification of compliance with the Rules during construction and operation.”
CSR applicability: ship types, length and contract date
The CSR apply to self-propelled bulk carriers and double hull oil tankers with unrestricted navigation, contracted for construction on or after 1 July 2015. CSR Pt 1 Ch 1 Sec 1 [1.1.1] sets the three conditions. Note 1 defines unrestricted navigation as “not subject to any geographical restrictions (i.e. any oceans, any seasons) except that limited by the ship’s capability for operation in ice.”
Ship types and size
The length measure is the freeboard length LLL, from the load line rules. The thresholds are:
- Bulk carriers: “These Rules apply to the hull structures of single side skin and double side skin bulk carriers having a freeboard length LLL of 90 m or above” ([1.2.1]).
- Oil tankers: “These Rules apply to the hull structures of double hull oil tankers having a freeboard length LLL of 150 m or above” ([1.3.1]).
An oil tanker “is defined as a ship which has to comply with Annex I of MARPOL73/78” (see MARPOL Annex I double hull rules) ([1.3.1]). The oil tanker article covers the type. Hybrid bulk carriers, with at least one hold with hopper and topside tanks, “are to comply with the strength criteria defined in these Rules” ([1.2.1]).
Figure 1 shows the two parts of the rules.
- Ch 1 Rule general principles
- Ch 2 General arrangement design
- Ch 3 Structural design principles
- Ch 4 Loads
- Ch 5 Hull girder strength
- Ch 6 Hull local scantling
- Ch 7 Direct strength analysis
- Ch 8 Buckling
- Ch 9 Fatigue
- Ch 10 Other structures
- Ch 11 Superstructure, deckhouses, outfitting
- Ch 12 Construction
- Ch 13 Ship in operation, renewal criteria
- Sec 1 General arrangement
- Sec 2 Structural design principles
- Sec 3 Hull local scantlings
- Sec 4 Local scantlings, L < 150 m
- Sec 5 Cargo hatch covers
- Sec 6 Grab notation
- Sec 1 General arrangement
- Sec 2 Structure design principles
- Sec 3 Hull local scantling
- Sec 4 Hull outfitting
Part 1 applies to both ship types; Part 2 adds the requirements of one type (CSR BC&OT, Foreword).
Excluded bulk carrier types
CSR [1.2.1] lists the bulk carrier types the rules do not cover:
- ore carriers
- combination carriers
- woodchip carriers
- cement, fly ash and sugar carriers, “provided that loading and unloading is not carried out by grabs heavier than 10 tons, power shovels and other means which may damage cargo hold structure”
- ships with inner bottom construction adapted for self-unloading
The ore carrier and woodchip carrier stubs cover those types. Container ships, general cargo ships and chemical tankers are not in the scope list. They are outside the scope of the CSR, under the society rules. The UR S11A article covers the IACS container ship standard.
The contract date
The contract date decides which edition binds a ship. Note 2 to [1.1.1] defines the contract for construction as the date the contract is signed between the prospective owner and the builder. The note refers to IACS PR 29. IACS PR 29 Rev.0 of July 2009 sets the rules for series ships:
- A series vessel takes the date of the series contract.
- An optional vessel counts as part of the series if the option is exercised “not later than 1 year after the contract” for the series.
- An amendment that adds vessels is a “new contract”.
- A change of ship type takes the date of the revised or new contract.
A bulk carrier of rule length L 90 m or above in unrestricted navigation, contracted on 30 June 2015, came under the earlier CSR for Bulk Carriers. The same ship contracted on 1 July 2015 comes under the CSR BC&OT.
Worked example: three ships
The examples below apply CSR Pt 1 Ch 1 Sec 1 and SOLAS II-1/3-10 to three example ships. The ships are examples, not real ships.
- Take a double side skin bulk carrier of LLL 120 m, contracted in 2020. The CSR apply, because LLL is 90 m or above. Local scantlings come from Part 2 Ch 1 Sec 4, and no BC-A, BC-B or BC-C feature is assigned.
- Check SOLAS II-1/3-10 for the same ship. The ship is under 150 m in length, so the regulation does not apply.
- Take a double hull oil tanker of LLL 180 m, contracted in 2017. The CSR apply in full, with FE analysis, fatigue and residual strength.
- Check SOLAS II-1/3-10 for the tanker. The contract is after 1 July 2016, so the regulation applies, and a Ship Construction File is kept.
- Take an ore carrier of LLL 230 m. The CSR do not apply ([1.2.1]), and SOLAS II-1/3-10 excludes ore carriers. The society rules apply.
Ships outside the CSR
CSR [1.1.3] states: “Ships for which these Rules are not applicable are to comply with the relevant Rules of the Society.” A bulk carrier under LLL 90 m, an ore carrier or a container ship follows its society’s rules and the IACS URs. [4.1.1] adds that the designer “should take care that parts of the structure that these Rules do not cover comply with the relevant requirements of the Society’s Rule.”
Class notations and service features
CSR [3.2.1] assigns three additional service features to bulk carriers of LLL 150 m or above:
| Feature | Cargo condition |
|---|---|
| BC-C | Dry bulk cargoes of density less than 1.0 t/m3 |
| BC-B | Density 1.0 t/m3 and above “with all cargo holds loaded in addition to BC-C conditions” |
| BC-A | Density 1.0 t/m3 and above “with specified holds empty at maximum draught in addition to BC-B conditions” |
Further features are:
- {Maximum cargo density in t/m3}, for BC-A and BC-B where below 3.0 t/m3
- {No MP}
- {Holds a, b, … may be empty}, for BC-A
- {Block loading}, for BC-A
The alternate hold loading article covers the empty-hold conditions.
CSR [3.2.2] makes the GRAB [X] notation mandatory for BC-A and BC-B ships. The grab mass X is not less than 35 t for L of 250 m or more. X is 30 t for 200 m to 250 m, and 20 t otherwise. The grabs and bulk handling stub covers the equipment.
Harmonization of the tanker and bulk carrier rules
IACS first wrote separate common rules for tankers and bulk carriers, then merged them into the CSR BC&OT for contracts from 1 July 2015. The IACS Council adopted the CSR for Double Hull Oil Tankers and the CSR for Bulk Carriers in December 2005.
Both rule sets applied to ships contracted for construction on or after 1 April 2006. The tanker rules covered “double hull oil tankers of 150m length, L, and upward” (CSR-OT July 2008, Sec 1 [1.1.1.1]). The bulk carrier rules covered ships “having length L of 90 m or above” (CSR-BC July 2012, Ch 1 Sec 1 [1.1.2]). The legacy rules used the rule length L, where the CSR BC&OT use the freeboard length LLL.
ClassNK records that the two sets had been developed “independently of each other by two separate teams”. The amendment outline states: “This harmonisation work started in 2008.” The drafts were “twice reviewed by industry members”, and “The harmonised common structural rules were finally adopted by IACS in December 2013.”
Figure 2 shows the dates from the first rules to the current edition.
IACS released the PDF of the 2015 rules on 25 March 2015. The Bureau Veritas, DNV and Lloyd’s Register articles describe each society’s part in developing the rules.
CSR Part 1: general hull requirements
Part 1 holds 13 chapters that apply to both bulk carriers and double hull oil tankers. CSR Pt 1 Ch 1 Sec 1 [2.2.1] states: “The provisions of the Ch 1, 2, 3, 4, 5, 6, 8, 12, 13 and Ch 10, Sec 4 are applicable all over the ships length. The Ch 7, 9, 10 and 11 define their own scope of application.”
| Chapter | Title | Spoke article |
|---|---|---|
| 1 | Rule General Principles | this article |
| 2 | General Arrangement Design | this article |
| 3 | Structural Design Principles | corrosion margins, higher tensile steel |
| 4 | Loads | still water, rule wave moment |
| 5 | Hull Girder Strength | section modulus, ultimate strength |
| 6 | Hull Local Scantling | none yet |
| 7 | Direct Strength Analysis | finite element analysis |
| 8 | Buckling | buckling |
| 9 | Fatigue | fatigue |
| 10 | Other Structures | none yet |
| 11 | Superstructure, Deckhouses and Hull Outfitting | none yet |
| 12 | Construction | none yet |
| 13 | Ship in Operation, Renewal Criteria | corrosion margins |
Chapter 1 has five sections: Application, Rule Principles, Verification of Compliance, Symbols and Definitions, and Loading Manual and Loading Instruments. The loading manual and loading computer article covers Section 5. Ch 1 Sec 3 [1.2.1] states: “For ships in service, the requirements in Ch 13 are to be complied with.”
Ch 1 Sec 3 [6] covers ships outside the design basis. The rules apply to ships of normal form, proportions, speed and structural arrangement. A ship of novel design, of unusual form, proportions, speed or structural arrangements outside those of Ch 1 Sec 2 [3.2], is specially considered ([6.2.1]). Information is to show that its structural safety is “at least equivalent to that intended by the Rules” ([6.2.2]). The Society “is to be contacted at an early stage in the design process” ([6.2.3]).
The design basis
CSR Pt 1 Ch 1 Sec 2 sets the assumptions behind every check:
- Design life: “A design life of 25 years is assumed for selecting ship design parameters” ([3.3.1]).
- Environment: “The rule requirements are based on a ship trading in the North Atlantic wave environment for its entire design life” ([3.4.1]).
- Hull form: L < 500 m, CB > 0.6, L/B > 5 and B/D < 2.5. “For ships over 350 m in length, special consideration is to be made for the wave loads by the Society” ([3.2.1]).
- Temperatures: air -10 deg C and seawater 0 deg C, as the lowest mean daily average ([3.4.4]).
- Loads not considered: wind and current ([3.4.2]), ice ([3.4.3]), and “The effects of thermal loads and residual stresses are not taken into account in the Rules” ([3.4.5]).
Three checks apply only to ships of LLL 150 m or above. These are residual strength ([3.1.3]), cargo hold FE analysis ([3.1.4]) and fatigue ([3.1.5]). The wave scatter diagram stub covers the North Atlantic data.
Structural principles and owner’s extras
CSR [1.1.2] assumes welded steel, stiffened plate panels framed longitudinally or transversely, with full transverse bulkheads and intermediate web frames. The typical arrangement assumes a double bottom and the engine room aft of the cargo region.
CSR [4.1.2] states that the structure “has a degree of redundancy” and is to “work in a hierarchical manner”. The structure is to keep reserve strength in damaged conditions, “e.g. collision, grounding or flooding scenarios”. The design maximum service speed is to be specified in the design specification ([3.9.1]).
Owner’s extras “are not specified by these Rules” ([3.10.1]). The CSR list vibration analysis, a maximum percentage of high strength steel, additional scantlings, an additional load margin and improved fatigue resistance. Such extras “are to be clearly specified in the design documentation”. The corrosion margins article covers the owner’s extra thickness tvol_add.
Probability levels
CSR Pt 1 Ch 1 Sec 2 [5.3.2] sets the dynamic global, local and impact loads at a probability level of \(10^{-8}\), and sloshing loads at \(10^{-4}\). [5.3.3] bases fatigue loads on the \(10^{-2}\) probability level of the dynamic load value.
Limit states and load scenarios
CSR [4.1.3] states: “The rules are based on the principles of limit state design.” The four limit states are serviceability (SLS), ultimate (ULS), fatigue (FLS) and accidental (ALS). The limit state design stub covers the method.
[4.2.1] names six design load scenarios: static (S), static plus dynamic (S+D), impact (I), sloshing (SL), fatigue (F) and accidental (A). ULS, SLS and FLS assume intact structure, and residual strength in the damaged condition is assessed for ALS ([4.3.5]). The FLS capacity model is “linear cumulative damage summation (Palmgren-Miner’s rule) in combination with a design S-N curve, a reference stress range and an assumed long-term stress distribution curve” ([4.3.3]).
Two design methods
CSR [5.1.1] uses two methods. Working stress design is “also known as the permissible or allowable stress method”.
Working stress design
where
| \(W_{stat}\) | load effect from static loads | varies |
| \(W_{dyn}\) | load effect from dynamic loads | varies |
| \(R\) | characteristic structural capacity, for example specified minimum yield stress or buckling capacity | varies |
| \(\eta_{1}, \eta_{2}\) | permissible utilization factors (resistance factors) |
Partial safety factor design is “also known as Load and Resistance Factor Design (LRFD)”.
Partial safety factor design
where
| \(W_{stat}\) | load effect from static loads | varies |
| \(W_{dyn}\) | load effect from dynamic loads | varies |
| \(R\) | characteristic structural capacity | varies |
| \(\gamma_{stat}, \gamma_{dyn}\) | partial safety factors on the static and dynamic load effects, for conditions A and B | |
| \(\gamma_{R}\) | partial safety factor on capacity |
Conditions A and B are tied to the probability level of the combined loads. The acceptance criteria of both methods “are calibrated … such that consistent and acceptable safety levels for all combinations of static and dynamic load effects are derived.” The hull girder ultimate strength uses the PSF method, and its “safety factors were determined using a structural reliability assessment approach” ([5.5.1]).
Minimum requirements and FE analysis
Some requirements apply in every case. CSR [5.2.1] states that the minimum requirements “are to be applied irrespective of all other requirements, hence thickness below the minimum is not allowed”. These are the minimum thickness, which does not depend on yield stress, and the minimum stiffness and proportions.
The FE model is “A linear elastic three dimensional finite element analysis of the cargo region (a FE model length of three holds is required)” ([5.5.2]). [5.5.4] states: “The scantlings defined by the prescriptive requirements are not to be reduced by any form of alternative calculations such as FE analysis, unless explicitly stated.”
CSR Part 2: bulk carrier and oil tanker requirements
Part 2 adds the requirements of each ship type, in Chapter 1 for bulk carriers and Chapter 2 for oil tankers. The CSR table of contents gives the sections:
- Ch 1 Bulk Carriers: Sec 1 General Arrangement Design; Sec 2 Structural Design Principles; Sec 3 Hull Local Scantlings; Sec 4 Hull Local Scantlings for Bulk Carriers L < 150 m; Sec 5 Cargo Hatch Covers; Sec 6 Additional Class Notation GRAB.
- Ch 2 Oil Tankers: Sec 1 General Arrangement Design; Sec 2 Structure Design Principles; Sec 3 Hull Local Scantling; Sec 4 Hull Outfitting.
Part 2 Ch 1 Sec 3 holds the bulk carrier double bottom and bulkhead checks for the flooded hold. Sec 5 covers the hatch covers of bulk carriers. The design cargo temperatures of an oil tanker are 80 deg C maximum and 0 deg C minimum (Pt 1 Ch 1 Sec 1 [1.3.2]).
Figure 3 shows how the CSR checks change with the freeboard length of a bulk carrier.
A bulk carrier of LLL 90 m to 150 m takes its local scantlings from Part 2 Ch 1 Sec 4. The FE analysis, fatigue and residual strength checks start at LLL 150 m. The bulk carrier size classes article covers the sizes in each band.
Gross and net thickness in the CSR
The CSR check strength on a net thickness and build the ship to a gross thickness, which adds the corrosion addition. CSR Pt 1 Ch 1 Sec 2 [4.3.4] states the two objectives of the net scantling approach:
Provide a relationship between the thickness used for strength calculations during the newbuilding stage and the minimum thickness accepted during the operational phase.
Enable the status of the structure with respect to corrosion to be clearly ascertained throughout the life of the ship.
The same clause states: “No credit is given in the assessment of structural capability for the presence of coatings or similar corrosion protection systems.” The protective coatings required by SOLAS are therefore given no strength credit.
The net scantling approach
Ch 3 Sec 2 applies the approach. The required gross thickness is the net thickness plus the corrosion addition tc. Local strength and buckling deduct the full tc, and hull girder properties, FE analysis, ultimate strength and fatigue deduct 0.5 tc. The corrosion margins article gives the formulas, the one-side values of Ch 3 Sec 3 and the renewal thickness of Ch 13.
The same plate therefore has three thicknesses in the rules. Take a plate of 16.0 mm as-built, with 0.5 mm owner’s extra and tc of 3.0 mm. The net thickness is 12.5 mm for buckling and 14.0 mm for the hull girder. These are the example values of the corrosion margins article.
CSR ships and non-CSR bulk carriers
A bulk carrier contracted before 1 April 2006, or outside the CSR scope, is a non-CSR ship. The ship follows its society’s rules and the IACS URs. The two routes differ in their sources:
| Item | CSR bulk carrier | Non-CSR bulk carrier |
|---|---|---|
| Scantling rules | CSR Part 1 and Part 2 Ch 1 | Society rules |
| Hull girder strength | Ch 5 | UR S11, UR S7 |
| Hold flooding | Pt 1 Ch 3 Sec 5 [2.5]; Pt 2 Ch 1 Sec 3 and Sec 4 | UR S17, S18 and S20 |
| SOLAS XII/5.2 | the CSR text does not refer to it | UI SC207 accepts UR S17, S18 and S20 |
| Renewal | Ch 13 | Society rules and UR S18, S19, S21, S31 |
| Net scantlings | Ch 3 Sec 2 | society rules |
For the flooded hold, CSR Pt 1 Ch 3 Sec 5 [2.5] states: “For bulk carriers, the yielding and ultimate strength of the hull girder in cargo hold flooded condition and in the damaged condition is to be assessed in accordance with Ch 5, Sec 1 and Ch 5, Sec 2.” The SOLAS Chapter XII article covers the statutory side.
The loading instrument of a CSR bulk carrier also checks the flooded condition. Ch 1 Sec 5 requires the loading instrument to confirm that the still water moment and shear force “in the hold flooded conditions do not exceed the specified permissible values”. Ch 4 Sec 6 [3] gives the pressures and forces due to dry cargoes in flooded conditions.
The IACS UR S series article covers the URs that carry “Non-CSR Bulk Carriers” in their titles. The bulk carrier article covers the ship type.
CSR design checks and their articles
Each CSR method has its own spoke article on this site. The table routes a reader from the check to the article and its anchor.
| Check | CSR reference | Article |
|---|---|---|
| Net scantlings and corrosion additions | Pt 1 Ch 3 Sec 2, Sec 3 | corrosion margins |
| Material factor k | Pt 1 Ch 3 Sec 1 | higher tensile steel |
| Still water moment and shear | Pt 1 Ch 4 Sec 4 | still water |
| Wave moment | Pt 1 Ch 4 Sec 4 | rule wave moment |
| Section modulus | Pt 1 Ch 5 Sec 1 | section modulus |
| Ultimate strength | Pt 1 Ch 5 Sec 2 | ultimate strength |
| Residual strength | Pt 1 Ch 5 Sec 3 | ultimate strength |
| Buckling | Pt 1 Ch 8 | buckling |
| Fatigue | Pt 1 Ch 9 | fatigue |
| Renewal in service | Pt 1 Ch 13 | corrosion margins |
The hull strength and longitudinal bending article is the hub for longitudinal strength across all rule sets. The primary supporting members stub covers the girders and web frames.
IMO verification under the goal-based standards
The IMO audits the CSR against its goal-based standards, and MSC 96 found the rules of 12 IACS societies conforming in May 2016. MSC.287(87), adopted on 20 May 2010, sets the standards in three tiers: “Tier I Goals; Tier II Functional requirements; Tier III Verification of conformity.”
Tier II has 15 functional requirements for bulk carriers and oil tankers in unrestricted navigation. Three match the CSR design basis:
- II.1: “The specified design life shall not be less than 25 years.”
- II.2: “Ships shall be designed in accordance with North Atlantic environmental conditions and relevant long-term sea state scatter diagrams.”
- II.6.2: “The corrosion addition shall be added to the net scantling and shall be adequate for the specified design life.”
The other functional requirements are:
- II.3 structural strength, including ultimate strength and safety margins “at net scantlings”
- II.4 fatigue life, “not less than the ship’s design life”
- II.5 residual strength
- II.6.1 coating life
- II.7 structural redundancy
- II.8 watertight and weathertight integrity
- II.9 human element considerations
- II.10 design transparency
- II.11 construction quality procedures
- II.12 survey during construction
- II.13 survey and maintenance
- II.14 structural accessibility
- II.15 recycling
CSR Pt 1 Ch 1 Sec 2 [2.2.2] excludes verification of compliance during construction and operation, the subject of II.12 and II.13.
SOLAS regulation II-1/3-10
MSC.290(87), adopted on 21 May 2010 and in force from 1 January 2012, added regulation II-1/3-10 to SOLAS Chapter II-1. Regulation 3-10.1 reads in part: “This regulation shall apply to oil tankers of 150 m in length and above and to bulk carriers of 150 m in length and above, constructed with single deck, top-side tanks and hopper side tanks in cargo spaces, excluding ore carriers and combination carriers”.
The regulation applies where the building contract is placed on or after 1 July 2016. Without a contract date, it applies to keels laid on or after 1 July 2017. It also applies to any ship delivered on or after 1 July 2020. Regulation 3-10.4 requires a Ship Construction File, “provided upon delivery of a new ship, and kept on board the ship and/or ashore and updated as appropriate throughout the ship’s service.”
The CSR scope and the SOLAS scope are not the same. A bulk carrier of LLL 100 m is under the CSR but under 150 m for II-1/3-10. The SOLAS regulation also covers only bulk carriers of the single deck, topside and hopper tank form. The rule length and freeboard length stub covers the two length measures.
The audits
The IMO press briefing of 13 May 2016 stated that “the 12 ROs’ ship construction rules were in conformity with the goals and functional requirements”. IACS recorded that the Maritime Safety Committee, “at its 96th session, has recognised the IACS-developed rules”. MSC 96 “agreed that the non-conformities identified were to be rectified”, as the MSC 98 summary records. The press briefing quoted the Secretary-General, Kitack Lim, that “there had been no direct oversight by IMO of the classification societies’ structural rules”. The IACS page on the CSR describes them as “the only Rules that comply with the Goal-Based Standards (GBS) set by the IMO”; that is the IACS statement.
| Session | Date | Decision |
|---|---|---|
| MSC 96 | May 2016 | Rules of 12 IACS societies conforming, non-conformities to be rectified |
| MSC 98 | June 2017 | Initial verification audit “successfully completed” |
| MSC 100 | December 2018 | Continued conformance, except DNV GL, sent to a re-verification audit |
| MSC 104 | October 2021 | Non-conformities of the 2018 CSR maintenance audit “duly rectified” |
MSC 104 stated that “IACS CSR and the DNV rules demonstrated continued conformance”. The next audits were to start “in early 2022 when the first three-year maintenance audit cycle begins.”
Verification guidelines
The initial audit ran under the guidelines of MSC.296(87), adopted on 20 May 2010. MSC.454(100), adopted on 7 December 2018, “REVOKES resolution MSC.296(87) on 1 January 2020” and replaces it with revised guidelines. Under MSC.454(100) 5.21, a rule change falls into one of three categories:
- “Corrigenda and follow-up change”: editorial corrections, or changes reflecting amendments to IMO mandatory instruments.
- “Minor change”.
- “Major change”: a “Change of basic methodology or technology or basic assumptions”.
Rule changes are submitted “at least annually”, and the IMO audits them “every three years”. Paragraph 17 states: “Ships contracted for construction to any new rules or rule changes to rules already verified as conforming to the Standards may be deemed to meet the Standards until a final decision is made by the Committee.”
CSR revision history and rule change notices
The CSR change by Rule Change Notices and corrigenda, and IACS issues a consolidated edition dated 01 JAN in most years. The current Foreword states: “These Rules enter into force on 1st July 2024 and supersede the following Rules: Common Structural Rules for Bulk Carriers and Oil Tankers, January 2023; Common Structural Rules for Bulk Carriers and Oil Tankers, January 2024”.
The Foreword lists two changes from the 01 JAN 2023 rules:
| Change | Adopted | Effective |
|---|---|---|
| Rule Change Notice 1 (2023), to rule version 01 JAN 2023 | 20 December 2023 | 1 July 2024 |
| Corrigenda 1 (2024), to rule version 01 JAN 2024 | 11 April 2025 | 1 July 2024 |
The corrigenda carry an effective date earlier than their adoption. The IACS publications register lists the file as “Common Structural Rules Consolidated 01 July 2025 edition”.
Rule change notices
The Foreword gives the label format “RCN {Number} to {Rule Version Date}”, for example “RCN1 to 01 JAN 2023”. A corrigendum carries a CORR label, such as “CORR1 to 01 JAN 2024”. Deleted text is replaced by the word “DELETED”.
Before adoption, IACS issues a Rule Change Proposal for industry review. RCP 1 (2017), for example, was issued on 1 May 2017. The IACS news register records consolidated 01 JAN editions released from 2017 to 2024, each made of the previous edition and its RCNs. The 01 JAN 2019 edition was the 01 JAN 2018 rules with RCN 1, Corr 1 and Corr 2 to 01 JAN 2018.
An urgent RCP of 8 June 2021 had one stated reason. IACS UR A1, A2 and Rec. 10 were to be implemented without exemption for CSR ships from 1 January 2022. The Foreword adds: “Full revision history for Common Structural Rules is available on IACS website, including all previous RCNs and associated TBs.”
The legacy rule sets
The legacy rules carried their own changes and dates. The CSR for Double Hull Oil Tankers record RCN 1 of 29 September 2006, effective 1 April 2007. RCN 2 of 25 February 2008 took effect on 1 July 2008. The RCN 1 implementation statement reads: “applied to ships contracted for construction on or after 1 April 2007. However, application to ships contracted for construction prior to 1 April 2007 is acceptable where agreed by builder and prospective owner.”
The bulk carrier revision history, as of 7 December 2012, lists four corrigenda in 2006 and 2007, all effective 1 April 2006. RCNs then took effect from 1 April 2008 to 1 July 2012. The last was RCN 1 to the 1 July 2010 consolidated edition, adopted 30 December 2011.
The pending CSR review
As of November 2024, IACS reports a review of the CSR that “will take several years to complete”. The IACS review page states that the wave loads are to be based on IACS Rec. 34 Rev.2 wave data “from 1990 to 2020”. IACS is “not planning to make any changes to the corrosion margins”. The page gives no adoption date, and the revised rules are to pass an IMO audit after IACS adopts them.
Common errors about the CSR
Most errors about the CSR concern their dates, their legal status or their scope. Each item names the error and the source that corrects it.
- “The CSR were adopted in 2014.” IACS adopted the harmonized rules in December 2013 (ClassNK 15-1-04e).
- “The CSR became mandatory on 1 January 2015.” The CSR BC&OT apply to contracts on or after 1 July 2015 (CSR [1.1.1]).
- “The CSR are an IMO regulation.” The CSR are class rules. SOLAS II-1/3-10 requires conforming rules, and MSC decides conformity (MSC.287(87) Tier III).
- “The CSR cover survey procedures.” The rules exclude verification of compliance during construction and operation (CSR Pt 1 Ch 1 Sec 2 [2.2.2]).
- “The CSR apply to container ships.” Container ships are outside the scope list; UR S11A covers their longitudinal strength.
- “The CSR apply to bulk carriers from 150 m.” The CSR start at LLL 90 m. The BC-A, BC-B and BC-C features and the FE, fatigue and residual strength checks start at LLL 150 m.
- “The tanker rules came after the bulk carrier rules.” Both applied to contracts from 1 April 2006.
- “FE analysis can reduce the scantlings.” Not unless explicitly stated (CSR [5.5.4]).
Limitations
This article summarizes the scope and structure of the CSR. The scantlings of a ship come from the full rules and the society that applies them. The rule text quoted is the 01 JAN 2024 rules with 01 JUL 2025 Corrigenda.
- The CSR review status is as IACS reported it in November 2024.
- The results of the IMO maintenance audits after MSC 104 are not given.
- The number of IACS societies that apply the CSR today is not stated; 12 was the count at MSC 96.
- The IMO meeting outcomes are quoted from the IMO meeting summaries and press briefing, not from the full MSC reports.
Frequently Asked Questions (FAQs)
What are the IACS Common Structural Rules?
The IACS Common Structural Rules (CSR BC&OT) are classification rules for the hull structure of bulk carriers and double hull oil tankers.
Part 1 holds the requirements common to both types, and Part 2 adds the requirements of each type.
Are the CSR an IMO instrument?
No. The CSR are the rules of the IACS member societies.
SOLAS regulation II-1/3-10 requires rules that conform to the IMO goal-based standards, and the Maritime Safety Committee decides on conformity (MSC.287(87), Tier III).
Which ships must comply with the CSR?
The CSR apply to self-propelled bulk carriers and double hull oil tankers with unrestricted navigation.
The ships are contracted for construction on or after 1 July 2015 (CSR Pt 1 Ch 1 Sec 1 [1.1.1]).
What is the length threshold for the CSR?
The CSR apply from a freeboard length LLL of 90 m or above for bulk carriers (CSR [1.2.1]).
Double hull oil tankers come under the CSR from LLL 150 m or above ([1.3.1]).
Which bulk carrier types do the CSR exclude?
Ore carriers, combination carriers, woodchip carriers and ships with an inner bottom adapted for self-unloading.
Cement, fly ash and sugar carriers are also excluded where grabs heavier than 10 tons, power shovels or similar are not used (CSR [1.2.1]).
What rules apply to a ship outside the CSR scope?
A ship outside the CSR scope follows the relevant rules of its classification society.
CSR Pt 1 Ch 1 Sec 1 [1.1.3] states that such ships are to comply with the relevant Rules of the Society.
What is an oil tanker for CSR purposes?
A ship which has to comply with Annex I of MARPOL 73/78 (CSR Pt 1 Ch 1 Sec 1 [1.3.1]).
The CSR cover double hull oil tankers of LLL 150 m or above.
What does the class notation CSR mean?
A ship that fully complies with the Common Structural Rules is assigned the notation CSR (CSR Pt 1 Ch 1 Sec 1 [3.1.1]).
What are BC-A, BC-B and BC-C?
Additional service features for bulk carriers of LLL 150 m or above.
BC-C covers cargoes of density below 1.0 t/m3. BC-B covers 1.0 t/m3 and above with all holds loaded, and BC-A adds specified holds empty at maximum draught (CSR [3.2.1]).
When is the GRAB notation mandatory?
For BC-A and BC-B ships (CSR [3.2.2]).
The grab mass X is at least 35 t for L of 250 m or more. X is 30 t for 200 m to 250 m, and 20 t otherwise.
What design life do the CSR assume?
The CSR assume a design life of 25 years (CSR Pt 1 Ch 1 Sec 2 [3.3.1]).
Functional requirement II.1 of the IMO goal-based standards, MSC.287(87), sets a design life of not less than 25 years.
What wave environment do the CSR assume?
The CSR assume the North Atlantic wave environment for the entire design life (CSR Pt 1 Ch 1 Sec 2 [3.4.1]).
Functional requirement II.2 of MSC.287(87) states the same environment.
What hull form limits do the CSR assume?
The CSR assume L under 500 m, CB over 0.6, L/B over 5 and B/D under 2.5 (CSR Pt 1 Ch 1 Sec 2 [3.2.1]).
For ships over 350 m, the society gives special consideration to the wave loads.
Do the CSR consider ice, wind or thermal loads?
No. CSR Pt 1 Ch 1 Sec 2 [3.4] does not consider wind and current or ice.
Thermal loads and residual stresses are not taken into account.
What is the net scantling approach?
The CSR check strength on net thickness and add the corrosion addition to obtain the gross thickness.
No credit is given for coatings (CSR Pt 1 Ch 1 Sec 2 [4.3.4]; Ch 3 Sec 2).
Why do the CSR use net scantlings?
Net scantlings relate the newbuilding strength thickness to the minimum thickness accepted in service.
CSR Pt 1 Ch 1 Sec 2 [4.3.4] states the objective.
What design methods do the CSR use?
The CSR use working stress design and partial safety factor design, each with conditions A and B (CSR Pt 1 Ch 1 Sec 2 [5.1.1]).
Which limit states do the CSR check?
The CSR check the serviceability, ultimate, fatigue and accidental limit states, SLS, ULS, FLS and ALS (CSR Pt 1 Ch 1 Sec 2 [4.1.3]).
Which checks apply only from LLL 150 m?
Three checks apply only from LLL 150 m: residual strength, cargo hold finite element analysis, and fatigue (CSR Pt 1 Ch 1 Sec 2 [3.1.3] to [3.1.5]).
Part 2 Ch 1 Sec 4 gives local scantlings for bulk carriers under 150 m.
Can finite element analysis reduce CSR scantlings?
No, unless the rule explicitly states it.
CSR Pt 1 Ch 1 Sec 2 [5.5.4] does not allow the prescriptive scantlings to be reduced by alternative calculations such as FE analysis.
What cargo temperatures do the CSR assume for oil tankers?
The CSR assume a maximum cargo temperature of 80 deg C and a minimum of 0 deg C (CSR Pt 1 Ch 1 Sec 1 [1.3.2]).
When did the first CSR enter into force?
The first CSR entered into force for contracts on or after 1 April 2006.
Both the bulk carrier rules and the double hull oil tanker rules took that date.
When were the tanker and bulk carrier rules harmonized?
IACS adopted the harmonized rules in December 2013, for ships contracted on or after 1 July 2015 (ClassNK amendment outline 15-1-04e; CSR [1.1.1]).
What is the current CSR edition?
The current edition is the 01 JAN 2024 rules with 01 JUL 2025 Corrigenda, in force from 1 July 2024.
The IACS register lists the file as the consolidated 01 July 2025 edition.
What is a Rule Change Notice?
A Rule Change Notice is an adopted change to the CSR, labelled RCN with its number and the rule version it changes, such as RCN 1 to 01 JAN 2023.
A corrigendum carries a CORR label (CSR Foreword).
How is the contract date defined?
PR 29 defines the contract date as the date the contract to build the ship is signed between the prospective owner and the shipbuilder.
IACS PR 29 sets the rules for series ships, options and amendments.
What does SOLAS regulation II-1/3-10 require?
Oil tankers and specified bulk carriers of 150 m and above are built to rules that conform to the goal-based standards.
The regulation applies to contracts from 1 July 2016, keels from 1 July 2017 or delivery from 1 July 2020 (MSC.290(87)).
When did the IMO find the CSR conforming to the goal-based standards?
MSC 96, in May 2016, recognized the rules of 12 IACS societies as conforming, with non-conformities to be rectified.
MSC 98, in June 2017, recorded the initial audit as completed.
Are the CSR audited again?
Yes. MSC.454(100) guidelines provide for rule changes made available at least annually, with a maintenance audit every three years.
MSC 104 in October 2021 found the IACS CSR in continued conformance.
What happens to a ship contracted under an unaudited rule change?
The ship is treated as compliant pending review.
Paragraph 17 of MSC.454(100) states that it ‘may be deemed to meet the Standards until a final decision is made by the Committee’.
What did a pre-CSR bulk carrier follow?
The rules of its classification society, with IACS URs such as S12, S17, S18 and S20.
UI SC207 links S17, S18 and S20 to SOLAS XII/5.2.
Is a new CSR edition planned?
IACS reports a multi-year review that uses the wave data of IACS Rec. 34 Rev.2, from 1990 to 2020.
IACS states no change to the corrosion margins and gives no adoption date.
Must a Ship Construction File be kept?
Yes, for ships under SOLAS II-1/3-10.
The file is provided on delivery and kept on board or ashore, and updated through the ship’s service (MSC.290(87)).
Do the CSR cover survey during construction?
No.
CSR Pt 1 Ch 1 Sec 2 [2.2.2] states that the Rules do not include requirements on the verification of compliance during construction and operation.
No question matches. Try a shorter or different word.
Sources
- IACS CSR BC&OT (1 January 2024 with 1 July 2025 Corrigenda). Common Structural Rules for Bulk Carriers and Oil Tankers iacs.s3.af-south-1.amazonaws.com
- IACS CSR for Double Hull Oil Tankers (July 2008 consolidated edition). Common Structural Rules for Double Hull Oil Tankers iacs.s3.af-south-1.amazonaws.com
- IACS CSR for Bulk Carriers (consolidated, effective 1 July 2012). Common Structural Rules for Bulk Carriers iacs.s3.af-south-1.amazonaws.com
- ClassNK Rule Amendment Outline 15-1-04e. Establishment of Common Structural Rules for Bulk Carriers and Oil Tankers classnk.com
- IACS PR 29 Rev.0 (July 2009). Definition of the date of contract for construction iacs.s3.af-south-1.amazonaws.com
- IMO Resolution MSC.287(87). International Goal-based Ship Construction Standards for Bulk Carriers and Oil Tankers (20 May 2010) imo.org
- IMO Resolution MSC.290(87). SOLAS regulation II-1/3-10 (21 May 2010) imo.org
- IMO Resolution MSC.454(100). Revised guidelines for verification of conformity with goal-based ship construction standards (7 December 2018) imo.org
- IMO MSC 104 meeting summary (4 to 8 October 2021). goal-based standards maintenance audit imo.org