MARPOL Annex I Special Areas: ten zones, dates, rules

The ten MARPOL Annex I Special Areas, their boundaries and in-effect dates, and the oil discharge allowed inside each: Reg 15.3 at 15 ppm, Reg 34.3, Antarctic.

Contents14 sections

A MARPOL Annex I special area is a sea area listed in Regulation 1.11 of MARPOL Annex I where oil discharge from ships is held to tighter limits than at sea generally. Regulation 1.11 of the revised Annex, adopted by resolution MEPC.117(52) on 15 October 2004 and in force from 1 January 2007, defines it as an area where “for recognized technical reasons in relation to its oceanographical and ecological condition and to the particular character of its traffic the adoption of special mandatory methods for the prevention of sea pollution by oil is required.”

Annex I names ten areas, and nine of them are in effect. The Oman area of the Arabian Sea is designated and in force as text, but its discharge rules have never taken effect (MEPC.1/Circ.778/Rev.5, 9 May 2025). Inside an area in effect, a ship of 400 GT and above may still discharge machinery-space bilge water at 15 ppm through equipment with an alarm and automatic stop (Regulation 15.3); an oil tanker may not discharge anything from its cargo area except clean or segregated ballast (Regulation 34.3); and in the Antarctic area no ship may discharge oil at all (Reg 15.4).

The cross-annex picture, covering the garbage, sewage and noxious liquid special areas and the Annex VI emission control areas, is on MARPOL special areas across all annexes. This page holds the Annex I register: boundaries, the three dates that attach to each area, and what a ship may and may not discharge inside one.

The Regulation 1.11 definition and the designation test

A special area exists in law only once an amendment writes it into Regulation 1.11, and the amendment follows the ordinary MARPOL Convention route under Article 16, normally by tacit acceptance. The definition has three limbs: oceanographic condition, ecological condition and the character of the area’s traffic. All three come from the regulation text, and the Assembly guidelines repeat them as the evaluation criteria.

Those guidelines are now resolution A.1087(28), the “2013 Guidelines for the Designation of Special Areas under MARPOL”, adopted on 4 December 2013. A.1087(28) revoked A.927(22) of 2001, whose first annex had carried the earlier special-area guidance, so any citation of A.927(22) for current practice is out of date. Paragraph 2.3 groups the criteria as oceanographic conditions, ecological conditions and vessel traffic characteristics. Paragraph 2.2 says a special area “may encompass the maritime zones of several States, or even an entire enclosed or semi-enclosed sea area”, and that designation on the stated criteria is meant “to avoid the proliferation of such areas”.

A proposal goes to the Marine Environment Protection Committee as a draft MARPOL amendment with a background document (A.1087(28) paragraph 3.2). Paragraph 3.3.2 allows a single proposal to cover Annexes I, II, IV and V together, but each Annex is “presented and evaluated separately”, and the Annex I and Annex V lists do differ. Paragraph 3.3.5 asks for information on the adequacy of reception facilities in the proposed area. Paragraph 2.7 states the consequence in one sentence: the requirements of a designation “can only become effective when adequate reception facilities are provided for ships”.

That sentence is the reason an Annex I special area has three dates instead of one. The amendment is adopted on one date, it enters into force on a second, and the discharge rules take effect on a third that depends on port infrastructure. For the Red Sea the gap between the second and the third was 41 years.

The ten Annex I special areas

The register below takes the boundaries from Regulation 1.11 as printed in MEPC.117(52) and MEPC.154(55), and the dates from the designating resolutions and MEPC.1/Circ.778/Rev.5. “In force” is the date the designating text bound the Parties; “in effect” is the date from which the special-area discharge rules of Regs 15 and 34 applied.

Reg 1.11AreaDesignated byIn forceIn effectEffect fixed by
.1Mediterranean SeaMARPOL 1973 text, 2 November 19732 October 19832 October 1983Annex I entry into force
.2Baltic SeaMARPOL 1973 text2 October 19832 October 1983Annex I entry into force
.3Black SeaMARPOL 1973 text2 October 19832 October 1983Annex I entry into force
.4Red SeaMARPOL 1973 text2 October 19831 January 2025MEPC.381(80), 7 July 2023
.5Gulfs areaMARPOL 1973 text2 October 19831 August 2008MEPC.168(56), 13 July 2007
.6Gulf of AdenMEPC.29(25), 1 December 19871 April 19891 January 2025MEPC.381(80), 7 July 2023
.7Antarctic areaMEPC.42(30), 16 November 199017 March 199217 March 1992MEPC.42(30) itself
.8North West European watersMEPC.75(40), 25 September 19971 February 19991 August 1999MEPC.77(41), 2 April 1998
.9Oman area of the Arabian SeaMEPC.117(52), 15 October 20041 January 2007Not in effectNone
.10Southern South African watersMEPC.154(55), 13 October 20061 March 20081 August 2008MEPC.167(56), 13 July 2007

Each area has a fixed legal boundary in Reg 1.11. The subsections give the boundary wording area by area.

Mediterranean Sea area

Reg 1.11.1 defines the Mediterranean Sea area as “the Mediterranean Sea proper including the gulfs and seas therein”, with the boundary against the Black Sea “constituted by the 41° N parallel” and the western limit at the Straits of Gibraltar “at the meridian of 005°36’ W”. The 41°N parallel crosses the Turkish Straits at the southern end of the Bosporus. Read with “the gulfs and seas therein”, that places the Sea of Marmara and the Dardanelles inside the Mediterranean area, not at its edge, and most of the Bosporus, which lies north of 41°N, in the Black Sea area.

The western line sits inside the Strait of Gibraltar, so an eastbound ship enters the special area only when it crosses 005°36’W. The Mediterranean has also been an Annex VI sulfur oxides emission control area since 1 May 2025, a separate designation covered on the Mediterranean SECA page. The regional framework for the same sea is the Barcelona Convention, which operates alongside MARPOL and does not change the Annex I discharge standard.

Baltic Sea area

Reg 1.11.2 covers “the Baltic Sea proper with the Gulf of Bothnia, the Gulf of Finland and the entrance to the Baltic Sea bounded by the parallel of the Skaw in the Skagerrak at 57°44.8’ N”. On a reading of that limit, the Kattegat and the Danish straits lie south of the Skaw parallel and are inside the area.

The Baltic is the only Annex IV special area, and with the Antarctic (Annexes I, II and V) one of two areas listed under three MARPOL annexes: Annex I for oil, Annex IV for passenger-ship sewage and Annex V for garbage. It is also an Annex VI emission control area (Baltic SECA and NECA). The regional instrument is the Helsinki Convention of 1992.

Black Sea area

Reg 1.11.3 defines the Black Sea area as “the Black Sea proper with the boundary between the Mediterranean Sea and the Black Sea constituted by the parallel 41° N”. The text names no strait, so the 41°N parallel is the whole of the boundary. The Sea of Azov is not named in Reg 1.11.3.

Red Sea area

Reg 1.11.4 defines the Red Sea area as “the Red Sea proper including the Gulfs of Suez and Aqaba”, closed at the south by the rhumb line from Ras si Ane (12°28.5’N, 043°19.6’E) to Husn Murad (12°40.4’N, 043°30.2’E) across the Bab el-Mandeb. Because the Gulf of Suez is inside the area, a southbound ship leaving the Suez Canal is in the special area from the canal’s southern entrance through the Gulf of Suez and the Strait of Gubal.

The Red Sea was one of the five areas written into the 1973 text. Its Annex I discharge rules took effect on 1 January 2025 under MEPC.381(80), and the Annex V garbage rules for the same sea took effect on that date under MEPC.382(80). The regional instrument is the Jeddah Convention of 1982.

Gulfs area

Reg 1.11.5 defines the Gulfs area as “the sea area located north-west of the rhumb line between Ras al Hadd (22°30’ N, 059°48’ E) and Ras al Fasteh (25°04’ N, 061° 25’ E)”. That line runs across the mouth of the Gulf of Oman. On a reading of the coordinates, the Gulfs area therefore takes in the Gulf of Oman, the Strait of Hormuz and the Persian Gulf, so “Gulfs area” and “Persian Gulf” are not synonyms.

The Gulfs area discharge rules took effect on 1 August 2008. MEPC.168(56), adopted on 13 July 2007, fixed that date for both the Annex I rules (Regs 15 and 34) and the Annex V garbage rules, citing Reg 38.6.1 of Annex I. The regional instrument for the same waters is the Kuwait Regional Convention of 1978.

Gulf of Aden area

Reg 1.11.6 defines the Gulf of Aden area as the part of the Gulf of Aden between the Red Sea and the Arabian Sea, bounded to the west by the same Ras si Ane to Husn Murad line that closes the Red Sea area and to the east by the rhumb line from Ras Asir (11°50’N, 051°16.9’E) to Ras Fartak (15°35’N, 052°13.8’E). The Red Sea and Gulf of Aden areas therefore share a boundary, and a ship transiting from Suez to the Arabian Sea is in one special area or the other from the Gulf of Suez to the Ras Asir line.

The Gulf of Aden was not in the 1973 text. Resolution MEPC.29(25), adopted on 1 December 1987, designated it, and the amendment entered into force on 1 April 1989. Its discharge rules took effect on 1 January 2025, on the same MEPC.381(80) decision as the Red Sea. The Gulf of Aden is an Annex I area only; it is not on the Annex V list.

Antarctic area

Reg 1.11.7 defines the Antarctic area as “the sea area south of latitude 60°S”, with no longitude limit. The same parallel bounds the area covered by the Antarctic Treaty of 1959. Resolution MEPC.42(30), adopted on 16 November 1990, designated the area under Annexes I and V and provided in its operative paragraph 4 that the requirements would take effect on the day the amendments entered into force, 17 March 1992. The Antarctic is the only area designated after 1973 whose rules took effect on the day its amendment entered into force.

The Antarctic area carries three rules no other Annex I area has: total prohibition of oil discharge from any ship under Reg 15.4, a retention-tank duty before entry under Reg 38, and the Reg 43 ban on heavy oils described below. The polar overlay is set out on Antarctic special area and the Polar Code.

North West European waters

Reg 1.11.8 states that North West European waters “include the North Sea and its approaches, the Irish Sea and its approaches, the Celtic Sea, the English Channel and its approaches and part of the North East Atlantic immediately to the west of Ireland”. The area is bounded by lines joining eight points:

  1. 48°27’N on the French coast
  2. 48°27’N, 006°25’W
  3. 49°52’N, 007°44’W
  4. 50°30’N, 012°W
  5. 56°30’N, 012°W
  6. 62°N, 003°W
  7. 62°N on the Norwegian coast
  8. 57°44.8’N on the Danish and Swedish coasts

The last point is the Skaw parallel that closes the Baltic area, so North West European waters and the Baltic Sea area meet on one line across the Skagerrak. On a reading of the coordinates, a ship sailing from the Bay of Biscay up the English Channel into the Baltic enters North West European waters at 48°27’N and stays inside one Annex I area or the other all the way to the Gulf of Finland. On a reading of the “North Sea and its approaches” limb, the Wadden Sea PSSA lies inside North West European waters.

Resolution MEPC.75(40), adopted on 25 September 1997, designated the area by amending what was then Reg 10, and it entered into force on 1 February 1999. MEPC.77(41), adopted on 2 April 1998, fixed 1 August 1999 as the date the Reg 10 requirements took effect. The Annex VI North Sea SECA and NECA covers a different polygon and should not be used as a proxy for the Annex I boundary.

Oman area of the Arabian Sea

Reg 1.11.9 defines the Oman area of the Arabian Sea as the sea area enclosed by 23 coordinate points. The first point, 22°30.00’N 059°48.00’E, is the Ras al Hadd point that also anchors the Gulfs area line. From there the polygon runs out to 063°22.22’E at 21°47.40’N, south to 13°45.86’N at 055°54.53’E, and back to the coast at 16°39.06’N 053°06.52’E.

The Oman area was added by the revised Annex itself, MEPC.117(52), so it was adopted on 15 October 2004 and entered into force on 1 January 2007. It has no effect date, for the reason set out in the section on effect dates below.

Southern South African waters

Reg 1.11.10 is the newest Annex I area. MEPC.154(55), adopted on 13 October 2006, added it, and the amendment entered into force on 1 March 2008. The polygon has eleven points, from 31°14’S 017°50’E on the west coast, south to 36°58’S 020°54’E, and east and north back to 33°27’S 027°12’E on the south-east coast. Traffic on the Cape of Good Hope route between the South Atlantic and the Indian Ocean crosses it.

MEPC.167(56), adopted on 13 July 2007, decided that the Reg 15 and Reg 34 special-area discharge requirements for Southern South African waters would take effect on 1 August 2008, provided the Reg 1.11 amendment entered into force on 1 March 2008, which it did. South Africa is the only bordering State, and the gap between entry into force and effect was five months.

Designated, in force and in effect: the three dates

An Annex I special area applies to ships from its in-effect date, not from its designation or its entry into force. The rule that creates the third date is in Regulation 38, the reception facilities regulation, and it applies by name to four areas: the Red Sea, the Gulfs area, the Gulf of Aden and the Oman area of the Arabian Sea.

How the effect date is fixed under Regulation 38

In the 2004 text of MEPC.117(52), Reg 38.6.1 provides that each Party concerned “shall notify the Organization of the measures taken” to provide special-area reception facilities, and that “Upon receipt of sufficient notifications the Organization shall establish a date from which the discharge requirements of regulations 15 and 34 of this Annex in respect of the area in question shall take effect.” The Organization notifies all Parties of the date “no less than twelve months in advance”.

The test is “sufficient notifications”, not notifications from every bordering State. In practice the resolutions record more: MEPC.77(41) and MEPC.168(56) recite notifications from all the States bordering North West European waters and the Gulfs area. The decision is taken by MEPC resolution and amends nothing.

Later amendments shifted the paragraph numbers. MEPC.216(63), in force 1 August 2013, inserted regional-arrangement paragraphs for small island developing States, and MEPC.359(79), in force 1 May 2024, replaced them with paragraphs covering both those States and ports within Arctic waters. MEPC.381(80) of July 2023 accordingly cites the date-fixing rule as Reg 38.8.1. This page writes it as Reg 38.8 (38.6 in the 2004 text), because MEPC.1/Circ.778/Rev.5 and 33 CFR 151.13(h) both still use the 2004 number.

North West European waters and Southern South African waters are not in the Reg 38.6 list of four. Their effect dates were still fixed by separate MEPC decisions, MEPC.77(41) and MEPC.167(56), so every area now in effect, other than the Mediterranean, Baltic, Black Sea and Antarctic areas, had its date fixed by a decision of the Committee.

Rules that apply before an area takes effect

Reg 38.6.2 (2004 text) states that until the date is established, “ships while navigating in the special area shall comply with the requirements of regulations 15 and 34 of this Annex as regards discharges outside special areas.” A ship in the Oman area of the Arabian Sea today therefore works to Reg 15.2 for bilge water and Reg 34.1 for cargo-area residues, including the 50 nm, en route, 30 litres per nautical mile and total-quantity conditions of Reg 34.1 (1/30,000 of the cargo, or 1/15,000 for tankers delivered on or before 31 December 1979).

The same rule governed the Red Sea and the Gulf of Aden until 31 December 2024. A tanker that discharged slops through its oil discharge monitoring and control system in the Red Sea in 2024, more than 50 nm from land and within the Reg 34.1 limits, complied with Annex I. The same discharge on 1 January 2025 was a violation.

Once an area takes effect, Reg 38.6.3 (2004 text) closes one loophole. A tanker loading at a port in the area that lacks reception facilities “shall also fully comply” with the special-area discharge rules, and a tanker entering the area to load “shall make every effort to enter the area with only clean ballast on board”.

Red Sea and Gulf of Aden: MEPC.381(80) and 1 January 2025

Resolution MEPC.381(80), adopted on 7 July 2023 at MEPC 80, decided that “the discharge requirements of regulations 15.3, 15.5 and 34.3 to 34.5 … in respect to the Red Sea and the Gulf of Aden Special Areas shall take effect on 1 January 2025.” The decision was taken under Reg 38.8.1 on notifications from bordering Parties, and the almost 18 months between adoption and effect exceeded the twelve-month minimum.

MEPC.381(80) is a date-fixing decision, not an amendment, and it is wrong to describe it as having “designated” either area. The Red Sea had been designated since 2 November 1973 and the Gulf of Aden since MEPC.29(25) in 1987. For the Red Sea, the Annex V garbage rules took effect on the same day under MEPC.382(80).

Oman area of the Arabian Sea: designated, not in effect

MEPC.1/Circ.778/Rev.5, issued by the IMO Secretariat on 9 May 2025, records the Oman area with an adoption date of 15 October 2004, entry into force of 1 January 2007, and no in-effect date. Its footnote 2, identical in Rev.4 of 30 October 2023, gives the reason: the requirements “have not yet taken effect because of lack of notifications from MARPOL Parties whose coastlines border the relevant Special Areas regarding the existence of adequate reception facilities”. Ships in the Oman area apply the outside-area rules until MEPC fixes a date and gives at least twelve months’ notice.

What Annex I allows inside a special area

Inside an Annex I special area in effect, the discharge rule depends on three facts: where the oily mixture came from, the ship’s gross tonnage, and whether the area is the Antarctic. The table is this site’s summary of Regs 15, 34 and 4 as they read in MEPC.117(52) with later amendments; the detailed conditions sit on the regulation pages linked in each row.

Source and shipOutside special areasInside a special area in effectAntarctic areaArctic waters
Machinery-space bilge, ship 400 GT and aboveReg 15.2: en route, Reg 14 equipment, 15 ppm without dilutionReg 15.3: same conditions, but Reg 14.7 equipment with alarm and automatic stopProhibited (Reg 15.4)Prohibited (Polar Code II-A 1.1.1)
Machinery-space bilge, ship under 400 GTReg 15.6: retain, or 15 ppm en route through Administration-approved equipmentReg 15.6, same termsProhibited (Reg 15.4)Prohibited (Polar Code II-A 1.1.1)
Tanker cargo area (slops, dirty ballast, tank washings)Reg 34.1: more than 50 nm from land, en route, 30 l/nm, 1/30,000 of cargo (1/15,000 if delivered on or before 31 December 1979), ODMCS and slop tanksProhibited (Reg 34.3)Prohibited (Reg 34.3, Reg 15.4)Prohibited (Polar Code II-A 1.1.1)
Clean or segregated ballastNot restricted (Reg 34.2)Not restricted (Reg 34.4)Not restrictedExcepted from the Polar Code prohibition
Cargo pump-room bilges on a tankerNot through the bilge route (Reg 15.2.4)Not through the bilge route (Reg 15.3.4)ProhibitedProhibited

Machinery spaces of ships of 400 GT and above

Reg 15.3 allows a ship of 400 GT and above to discharge machinery-space oily mixtures in a special area if all five conditions are met: the ship is proceeding en route; the mixture is processed through oil filtering equipment meeting Reg 14.7; the oil content of the effluent without dilution does not exceed 15 ppm; on a tanker, the mixture does not come from cargo pump-room bilges; and on a tanker, it is not mixed with oil cargo residues. These are the same five conditions as Reg 15.2 outside special areas, with one difference in the equipment limb.

That difference decides the outcome for many ships. Regulation 14 requires 15 ppm oil filtering equipment on ships of 400 GT to under 10,000 GT (Reg 14.6), and adds the 15 ppm alarm and automatic stopping device only at 10,000 GT and above (Reg 14.7). A 6,000 GT feeder fitted to the Reg 14.6 minimum can discharge processed bilge water in the open Atlantic but not in the Baltic, the Mediterranean or North West European waters; inside those areas it retains everything in its bilge holding tank. A 6,000 GT ship that has been fitted with a 14.7-compliant oily water separator, alarm and stop can discharge in all three.

Reg 15 contains no distance-from-land condition, inside or outside special areas. The 12 nm figure that appears in older guidance came from a transitional Reg 9(7) inserted by MEPC.51(32) for unfitted ships until 6 July 1998; a 12 nm distinction survives in the United States in 33 CFR 151.10. “En route” is not defined in Annex I Reg 1; the term is discussed on en route under MARPOL.

Ships of less than 400 GT

Reg 15.6 governs ships of less than 400 GT in all areas except the Antarctic and Arctic waters, so it applies inside special areas on the same terms as outside them. Oil and oily mixtures are either retained for discharge to reception facilities, or discharged en route through equipment approved by the Administration that keeps the effluent at or below 15 ppm without dilution, with no cargo pump-room bilge water and no cargo residues. Reg 14.4 asks the Administration to ensure such ships are equipped “as far as practicable” to retain on board or discharge in line with Reg 15.6.

Tanker cargo area

Reg 34.3 states that “any discharge into the sea of oil or oily mixture from the cargo area of an oil tanker shall be prohibited while in a special area”. Unlike Reg 15, the outside-area cargo rule names the special-area condition directly: Reg 34.1.1 requires that “the tanker is not within a special area”. Inside an area in effect, slops from slop tanks, dirty ballast and tank washings stay on board for a reception facility or for lawful discharge after the ship leaves the area.

Two exceptions apply. Reg 34.4 lets clean or segregated ballast go overboard in a special area, and Reg 34.5 lets a ship on a voyage only part of which is in a special area discharge outside it under Reg 34.1. Reg 34.6 adds that tankers of less than 150 GT are outside the slop tank, ODMCS and interface detector regulations (Regs 29, 31 and 32) and control their cargo residues by retention on board and discharge of all contaminated washings to reception facilities, unless adequate arrangements are made to ensure that any effluent allowed to be discharged into the sea is effectively monitored.

Antarctic area and Arctic waters

Reg 15.4 provides that in the Antarctic area “any discharge into the sea of oil or oily mixtures from any ship shall be prohibited”. No ppm route exists, and the rule applies to every ship regardless of tonnage. Arctic waters are not an Annex I special area, but Polar Code Part II-A paragraph 1.1.1, made mandatory through MARPOL by MEPC.265(68) from 1 January 2017, prohibits any discharge into Arctic waters of oil or oily mixtures from any ship, with clean or segregated ballast excepted. The Polar Code page covers the Arctic boundary and the ship categories.

Voyages partly inside an area and the Regulation 4 exceptions

Reg 15.5 and Reg 34.5 make the special-area rules geographic, not voyage-based. A ship whose voyage passes through North West European waters and then continues into the open Atlantic may discharge after leaving the boundary under the outside-area rules, provided the conditions of Reg 15.2 or Reg 34.1 are met there. Nothing in Annex I lets a ship carry an “in transit” exemption through a special area.

Regulation 4 disapplies Regs 15 and 34, and Polar Code II-A 1.1.1, for three cases: a discharge necessary to secure the safety of a ship or save life at sea; a discharge resulting from damage to the ship or its equipment where all reasonable precautions were taken and the owner or master did not act with intent or recklessly with knowledge that damage would probably result; and approved oil-containing substances used to combat a specific pollution incident. The exceptions apply inside special areas exactly as outside them. The limbs are set out on the Regulation 4 exceptions.

Ships trading only inside special areas

Reg 14.5 lets the Administration waive the Reg 14.1 and 14.2 equipment for a ship engaged exclusively on voyages within special areas or Arctic waters, and for a high-speed craft on a scheduled service with a turnaround of no more than 24 hours. The ship must have a holding tank with volume adequate for all its oily bilge water, discharge that water to reception facilities, carry an IOPP Certificate endorsed to show the waiver, and record every discharge in the Oil Record Book.

Reception facilities inside special areas

The special-area reception duty in Reg 38 (Part B of the regulation) is wider than the general port duty. In the 2004 text, Reg 38.4 required coastal Parties bordering a special area to ensure “that all oil loading terminals and repair ports within the special area are provided with facilities adequate for the reception and treatment of all the dirty ballast and tank washing water from oil tankers”, and that “all ports within the special area” have adequate reception facilities for other residues and oily mixtures from all ships, without undue delay. In current numbering that paragraph is 38.5.

Reg 38.5 of the 2004 text adds that ports at the entrance of seawater courses with low depth contour may meet the duty with facilities that leave ships discharging slops or dirty ballast “subject to some delay”. After an area takes effect, Parties notify IMO of all cases where facilities are alleged to be inadequate (Reg 38.6.4 and 38.8 of the 2004 text). IMO records the facilities States report in the GISIS port reception facilities database.

The Antarctic area has its own paragraph (38.7 in the 2004 text). Parties whose ports ships “depart en route to or arrive from the Antarctic area” undertake to provide, “as soon as practicable”, facilities for all sludge, dirty ballast, tank washing water and other oily residues and mixtures. Each Party also ensures its own ships are fitted, before entering the area, with tanks of sufficient capacity to retain those residues while operating there, and have arranged to discharge them at a reception facility after leaving.

Small island developing States may meet the reception-facility duties, including the special-area duty, through regional arrangements under a Regional Reception Facilities Plan. MEPC.216(63) introduced the option for small island developing States from 1 August 2013, and MEPC.359(79) extended regional arrangements to States bordering Arctic waters, for their ports within Arctic waters, from 1 May 2024.

Heavy oils in polar waters: Regulations 43 and 43A

Regulation 43 bans heavy oils from the Antarctic area as cargo and as fuel. Resolution MEPC.189(60), adopted on 26 March 2010 and in force from 1 August 2011, added Annex I Chapter 9 and Reg 43. Reg 43.1 prohibits in the Antarctic area the carriage in bulk as cargo, or carriage and use as fuel, of:

  • crude oils with a density at 15°C higher than 900 kg/m3;
  • other oils with a density at 15°C higher than 900 kg/m3 or a kinematic viscosity at 50°C higher than 180 mm2/s;
  • bitumen, tar and their emulsions.

Reg 43.1 excepts “vessels engaged in securing the safety of ships or in a search and rescue operation”, so the ban is not absolute. Reg 43.2 adds that a ship that previously carried or used those oils does not have to clean or flush its tanks or pipelines before entering. Reg 43 is a carriage and use rule, separate from the zero-discharge rule of Reg 15.4.

Reg 43A applies a narrower rule to Arctic waters, which are not a special area. MEPC.329(76), adopted on 17 June 2021, entered into force on 1 November 2022. From 1 July 2024 it prohibits the use and carriage for use as fuel of the Reg 43.1.2 oils in Arctic waters, with exceptions for safety, search and rescue and dedicated oil spill response ships. Ships to which Reg 12A or Polar Code II-A 1.2.1 applies (protected fuel tanks) are covered from 1 July 2029, and a State bordering Arctic waters may waive the ban for its own ships in its own waters until the same date. Reg 43A covers fuel only, not crude or bitumen cargo. Both rules are treated in full on heavy grade oil in polar waters.

Special areas, emission control areas, PSSAs and the other annexes

An Annex I special area, an Annex VI emission control area and a Particularly Sensitive Sea Area are three different legal instruments that sometimes cover the same water.

DesignationLegal basisWhat it controlsExample overlapping an Annex I area
Annex I special areaReg 1.11, by MARPOL amendment under Article 16; criteria in A.1087(28)Oil discharge into the seaAll ten
Annex V special areaAnnex V Reg 1, by amendmentGarbage dischargeMediterranean, Baltic, Black Sea, Red Sea, Gulfs, Antarctic; the Annex V North Sea area lies within North West European waters
Emission control areaAnnex VI Reg 13 and 14, by amendmentSOx, particulate matter, NOx emissions to airBaltic, Mediterranean SOx ECA from 1 May 2025
Particularly Sensitive Sea AreaMEPC resolution under A.982(24)Associated protective measures (routeing, areas to be avoided, reporting) adopted under other instrumentsWadden Sea, Baltic Sea

The annex lists do not match. Annex V has eight special areas: the Mediterranean, Baltic, Black Sea, Red Sea, Gulfs area, North Sea, Antarctic area and Wider Caribbean Region. The Gulf of Aden, North West European waters, the Oman area and Southern South African waters are Annex I areas only, and the Wider Caribbean is an Annex V area only. Annex II has one special area, the Antarctic, and Annex IV has one, the Baltic Sea, for passenger-ship sewage.

A PSSA does not change the Annex I discharge standard. Where a PSSA lies inside an Annex I special area, as the Baltic Sea PSSA does, the ship applies the special-area oil rules because of Reg 1.11 and the PSSA’s own protective measures because of the instruments that adopted them. A PSSA outside the ten areas, such as the Great Barrier Reef PSSA, leaves the ship on the outside-area rules of Regs 15.2 and 34.1.

Special-area discharge records, survey and port State control

Every special-area discharge leaves a paper trail that a port State control officer can read against the chart. In the Oil Record Book Part I form as amended by MEPC.187(59) (in force 1 January 2011), a machinery-space discharge through 15 ppm equipment is recorded under code D, item 15.1, with the position at the start and end, or under code E for an automatic discharge. A port State officer comparing those positions with the Reg 1.11 boundaries can see whether a discharge took place inside a special area and whether the ship was fitted with Reg 14.7 equipment at the time. Tanker cargo and ballast operations go in Oil Record Book Part II, and the Part I and Part II books are kept for three years.

Oil filtering equipment approved under resolution MEPC.107(49), which applies to equipment on ships keel-laid on or after 1 January 2005 and to new installations on older ships from that date, keeps a record of date, time, alarm status and operating status for at least 18 months (paragraph 4.2.9). Inspectors use that record to check discharges claimed in the Oil Record Book against the alarm’s own log. The Supplement to the IOPP Certificate records the oil filtering equipment fitted, which settles whether a Reg 15.3 discharge was available to the ship.

Operational control is under Regulation 11, which allows a port State to inspect operational requirements where there are clear grounds to believe the master or crew are not familiar with essential shipboard procedures. The current IMO procedures are resolution A.1206(34), adopted on 3 December 2025; regional regimes such as the Paris MoU apply them through their own instructions. A ship that discharged in an area in effect with Reg 14.6 equipment only, or with a Reg 14.7 system whose automatic stop did not work, breached Reg 15.3 whatever the reading on its oil content meter. A deliberate bypass of the separator, the magic pipe, is a breach anywhere, special area or not.

Regional overlays on the Annex I special areas

The IMO text is the baseline, and the main national overlay that departs from it is in United States regulations. Regional seas conventions add cooperation duties but do not rewrite the Annex I discharge standard.

United States

33 CFR 151.06 reproduces the Reg 1.11 definitions, and 33 CFR 151.13(a) lists all ten areas, then states that “The discharge restrictions are effective in the Mediterranean Sea, Baltic Sea, Black Sea, and the Antarctic area.” Paragraph (h) provides that the restrictions for the Red Sea, Gulfs area, Gulf of Aden, Oman area and Southern South African waters “will enter into effect” when bordering Parties certify reception facilities and IMO sets a date, with notice in the Federal Register. The section still cites “Regulation 38.6.1” and was last amended in 2015 (80 FR 5933), so it does not reflect the 1999, 2008 and 2025 effect dates MEPC has fixed. North West European waters appears neither among the four effective areas in paragraph (a) nor among the pending areas in paragraph (h).

The structure of 151.13 also differs from Reg 15.3. Paragraph (b)(1) states that a ship of 400 gross tons or over and any oil tanker “may not discharge oil or oily mixture within a special area”, and paragraph (d) then lifts that bar for processed machinery-space bilge water meeting six conditions, including a device that stops the discharge automatically above 15 ppm. The outcome matches Reg 15.3 for a fitted ship. US-flag ships abroad and foreign ships in US waters are subject to the Act to Prevent Pollution from Ships, and 33 CFR 151.10 keeps a 12 nm distinction for discharges outside special areas that the IMO text no longer has.

Regional seas conventions

Six of the ten Annex I areas lie within regional pollution conventions: the Barcelona Convention for the Mediterranean, the Helsinki Convention for the Baltic, the Bucharest Convention of 1992 for the Black Sea, the Kuwait Regional Convention for the waters of the Gulfs area, and the Jeddah Convention for the Red Sea and Gulf of Aden. Several sit within the UNEP Regional Seas Programme. They organize cooperation, monitoring and emergency response, but a ship’s oil discharge standard inside those seas comes from MARPOL Annex I.

Common misreadings of the special-area rules

“No oil discharge is allowed in a special area.” Correct only for the Antarctic area and for tanker cargo-area discharge. Machinery-space bilge water may go overboard at 15 ppm en route through Reg 14.7 equipment in every other special area in effect (Reg 15.3).

“Special areas apply from designation.” The Red Sea was designated in 1973 and was not in effect until 1 January 2025. Ships in a designated area without an effect date, today only the Oman area, follow the outside-area rules (Reg 38.6.2 of the 2004 text).

“The Gulfs area is the Persian Gulf.” The Gulfs area boundary runs from Ras al Hadd to Ras al Fasteh, across the mouth of the Gulf of Oman, so the Gulf of Oman and the Strait of Hormuz are inside it. The Gulf of Aden is a separate area (Reg 1.11.6), not part of the Gulfs area.

“The Arctic is a special area.” It is not, under any MARPOL annex. The zero-discharge rule there comes from the Polar Code, and the heavy fuel oil rule from Reg 43A.

“MEPC.381(80) designated the Red Sea special area.” It fixed an effect date for an area designated 50 years earlier.

“A ship below 400 GT is exempt in special areas.” Reg 15.6 applies inside special areas, with retention or Administration-approved 15 ppm equipment.

“The 12 nm rule applies in special areas.” No distance-from-land condition exists in Reg 15. The 50 nm rule in Reg 34.1 is an outside-area cargo rule and has no role inside a special area, where cargo-area discharge is prohibited.

Limitations

This page summarizes Annex I as amended to MEPC.381(80) and MEPC.1/Circ.778/Rev.5 of 9 May 2025. The paragraph numbers of Reg 38 changed after MEPC.216(63) and MEPC.359(79), and the mapping of the 2004 paragraphs 38.4 to 38.8 onto current 38.5 to 38.10 is derived from those amending resolutions and from MEPC.381(80)’s own citation of Reg 38.8.1, not from a consolidated edition. Cite both numbers in correspondence with a flag Administration or port State.

The statements that the Gulfs area includes the Gulf of Oman and the Strait of Hormuz, that the Sea of Marmara and the Dardanelles are in the Mediterranean area and the Bosporus in the Black Sea area, that the Kattegat is in the Baltic area and the Skagerrak in North West European waters, and that the Wadden Sea lies inside North West European waters are readings of the Reg 1.11 coordinates and wording. They are not stated in those words in the regulation. A ship working close to a boundary should plot the Reg 1.11 coordinates on the working chart rather than rely on a named sea.

National law can differ from the IMO position. 33 CFR 151.13 still treats only four areas as effective; an Administration’s own regulations may lag or lead IMO in the same way. The register on this page gives no date for the Oman area, and none should be assumed until MEPC adopts a decision and gives twelve months’ notice. The Annex VI and Annex V rows in the comparison table are summaries; the governing text is on the linked pages.

Frequently Asked Questions (FAQs)

How many MARPOL Annex I special areas are there, and are all of them in effect?

Annex I lists ten special areas in Regulation 1.11.1 to 1.11.10.

Nine are in effect. The Oman area of the Arabian Sea (Reg 1.11.9) has been in force as treaty text since 1 January 2007 but has no effect date, because IMO has not received the reception-facility notifications it needs (MEPC.1/Circ.778/Rev.5, 9 May 2025).

What is the difference between a special area being designated, entering into force and taking effect?

Designation is the adoption of the amendment that writes the area into Regulation 1.11.

Entry into force is the date that amendment binds the Parties under the MARPOL Article 16 tacit acceptance procedure. Taking effect is the date from which the special-area discharge rules of Regs 15 and 34 actually apply. For the Mediterranean, Baltic, Black Sea and Antarctic areas it coincided with entry into force; for the others MEPC fixed a later date once it received sufficient notifications of adequate reception facilities. The Red Sea was designated on 2 November 1973, was in force from 2 October 1983 and took effect on 1 January 2025.

Which Annex I special areas took effect on 1 January 2025?

The Red Sea area (Reg 1.11.4) and the Gulf of Aden area (Reg 1.11.6).

Resolution MEPC.381(80), adopted 7 July 2023, decided that Regulations 15.3, 15.5 and 34.3 to 34.5 take effect for both areas on 1 January 2025. The Annex V garbage requirements for the Red Sea took effect on the same date under MEPC.382(80).

Does MEPC.381(80) amend MARPOL Annex I?

No. MEPC.381(80) is a decision of the Committee under the reception-facility paragraph of Regulation 38 (Reg 38.8.1 in current numbering, 38.6.1 in the 2004 text).

It fixes the date from which existing Annex I provisions apply in the Red Sea and Gulf of Aden. It did not pass through the Article 16 amendment procedure and changes no text.

Why has the Oman area of the Arabian Sea never taken effect?

MEPC.1/Circ.778/Rev.5 (9 May 2025), like Rev.4 of 30 October 2023, states that the special-area requirements have not taken effect because of a lack of notifications from the MARPOL Parties bordering the area that adequate reception facilities exist.

Until MEPC fixes a date with at least twelve months’ notice, ships in the Oman area follow the outside-special-area rules of Regs 15 and 34.

Is the Gulfs area the same as the Persian Gulf?

No. Reg 1.11.5 defines the Gulfs area as the sea north-west of the rhumb line from Ras al Hadd (22°30’N, 059°48’E) to Ras al Fasteh (25°04’N, 061°25’E).

On a reading of those coordinates, the line closes the mouth of the Gulf of Oman, so the Gulfs area takes in the Gulf of Oman and the Strait of Hormuz as well as the Persian Gulf. It took effect on 1 August 2008 under MEPC.168(56).

Does the Red Sea special area include the Gulf of Suez and the Gulf of Aqaba?

Yes. Reg 1.11.4 defines the Red Sea area as the Red Sea proper including the Gulfs of Suez and Aqaba, bounded at the south by the rhumb line from Ras si Ane (12°28.5’N, 043°19.6’E) to Husn Murad (12°40.4’N, 043°30.2’E).

A southbound ship leaving the Suez Canal enters the special area in the Gulf of Suez.

Where does the Mediterranean special area end at Gibraltar and at the Turkish Straits?

Reg 1.11.1 bounds the Mediterranean Sea area to the west at the Straits of Gibraltar on the meridian of 005°36’W, and draws its boundary with the Black Sea on the 41°N parallel.

The area includes ’the gulfs and seas therein’, which on a reading of those limits places the Sea of Marmara and the Dardanelles in the Mediterranean area.

Does the Baltic special area include the Kattegat?

Yes. Reg 1.11.2 defines the Baltic Sea area as the Baltic proper with the Gulfs of Bothnia and Finland and the entrance to the Baltic bounded by the parallel of the Skaw at 57°44.8’N.

On a reading of the coordinates, the Kattegat lies south of that parallel and inside the area, and the Skagerrak north of it falls inside North West European waters, whose boundary also ends at 57°44.8’N on the Danish and Swedish coasts.

Where is the boundary of the North West European waters special area?

Reg 1.11.8 covers the North Sea and its approaches, the Irish Sea and its approaches, the Celtic Sea, the English Channel and its approaches and part of the North East Atlantic west of Ireland, bounded by lines joining 48°27’N on the French coast, 48°27’N 006°25’W, 49°52’N 007°44’W, 50°30’N 012°W, 56°30’N 012°W, 62°N 003°W, 62°N on the Norwegian coast and 57°44.8’N on the Danish and Swedish coasts.

It took effect on 1 August 1999 (MEPC.77(41)).

Can a ship discharge processed bilge water inside an Annex I special area?

Yes, except in the Antarctic area.

Reg 15.3 allows a ship of 400 GT and above to discharge machinery-space oily mixtures in a special area if it is proceeding en route, the mixture is processed through oil filtering equipment meeting Reg 14.7, the oil content without dilution does not exceed 15 ppm, and the mixture does not come from cargo pump-room bilges or contain cargo residues on a tanker.

Can a 5,000 GT cargo ship discharge bilge water in a special area?

Only if it has Reg 14.7 equipment: a 15 ppm bilge alarm with an automatic stopping device.

Reg 14.6 requires only 15 ppm oil filtering equipment on ships of 400 to under 10,000 GT, but Reg 15.3.2 requires 14.7 equipment for any discharge inside a special area. A 5,000 GT ship fitted to the 14.6 minimum retains its bilge water inside the area.

What rule applies to a ship of less than 400 GT in a special area?

Reg 15.6 applies in all areas except the Antarctic and Arctic waters, special areas included.

The ship either retains oil and oily mixtures for discharge to reception facilities, or discharges them en route through equipment approved by the Administration that keeps the effluent at or below 15 ppm without dilution, with no cargo pump-room bilge water and no cargo residues.

Is any oil discharge allowed in the Antarctic area?

No. Reg 15.4 prohibits any discharge into the sea of oil or oily mixtures from any ship in the Antarctic area, the sea south of 60°S.

Reg 34.3 bars cargo-area discharge in every special area, and Reg 4 exceptions for safety, damage and approved response substances still apply.

Is the Arctic an Annex I special area?

No. Arctic waters do not appear in Reg 1.11 or in MEPC.1/Circ.778/Rev.5.

Discharge of oil or oily mixtures into Arctic waters is prohibited instead by Polar Code Part II-A paragraph 1.1.1, made mandatory through MARPOL by MEPC.265(68) from 1 January 2017, and heavy fuel oil is restricted there by Annex I Reg 43A.

Can a tanker discharge cargo-tank washings or dirty ballast in a special area?

No. Reg 34.3 prohibits any discharge into the sea of oil or oily mixture from the cargo area of an oil tanker while in a special area.

The outside-area allowance of Reg 34.1 (more than 50 nm from land, en route, 30 litres per nautical mile, ODMCS and slop tanks) is not available inside one. Washings stay in the slop tanks for a reception facility or for discharge after the ship leaves the area.

Is clean or segregated ballast discharge allowed in a special area?

Yes.

Reg 34.4 states that the special-area prohibition in 34.3 does not apply to the discharge of clean or segregated ballast.

Is there a distance-from-land rule for machinery-space discharge in a special area?

No. Reg 15 contains no distance-from-land condition, inside or outside special areas.

The 50 nm condition belongs to tanker cargo-area discharge outside special areas under Reg 34.1.2. The United States keeps a 12 nm distinction in 33 CFR 151.10 as a domestic overlay.

Can a ship that only passes through a special area discharge outside it on the same voyage?

Yes.

Reg 15.5 and Reg 34.5 state that nothing prohibits a ship on a voyage only part of which is in a special area from discharging outside the area under the outside-area rules of Reg 15.2 or Reg 34.1.

Do the Regulation 4 exceptions apply inside a special area?

Yes. Reg 4 disapplies Regs 15 and 34 for a discharge necessary to secure the safety of a ship or save life at sea, for a discharge resulting from damage where all reasonable precautions were taken and there was no intent or recklessness, and for approved substances used to combat a specific pollution incident.

Those exceptions apply equally inside special areas and in Arctic waters.

What must a ship have before entering the Antarctic area?

Annex I Reg 38 (38.7 in the 2004 text, 38.9 in current numbering) requires each Party to ensure its ships, before entering the Antarctic area, have tank capacity to retain all sludge, dirty ballast, tank washing water and other oily residues and mixtures while operating there, and have arranged to discharge them at a reception facility after leaving.

What does Regulation 43 ban in the Antarctic area?

Reg 43, added by MEPC.189(60) and in force 1 August 2011, prohibits carriage in bulk as cargo, use as ballast (added by MEPC.256(67) from 1 March 2016), and carriage and use as fuel, of crude oils with a density above 900 kg/m3 at 15°C, other oils above 900 kg/m3 at 15°C or above 180 mm2/s at 50°C, and bitumen, tar and their emulsions in the Antarctic area.

Ships engaged in securing the safety of ships or in search and rescue are excepted.

What must a tanker do when loading in a special-area port without reception facilities?

Once an area has taken effect, a tanker loading in a port there without facilities still complies with the special-area discharge rules of Regs 15 and 34.

Reg 38 (38.6.3 in the 2004 text) adds that tankers entering the area to load shall make every effort to enter with only clean ballast on board.

How does IMO decide whether to designate a new special area?

Under A.1087(28), the 2013 Guidelines for the Designation of Special Areas under MARPOL, a proposal goes to MEPC as a draft MARPOL amendment with a background document.

It must show oceanographic conditions, ecological conditions and vessel traffic characteristics that justify the area, and information on reception facilities. Each Annex is evaluated separately, and adoption follows the Article 16 procedure.

Is an Annex I special area the same as a PSSA or an emission control area?

No. A special area is written into a MARPOL Annex by amendment and changes discharge standards.

A Particularly Sensitive Sea Area is designated by MEPC under A.982(24) and carries associated protective measures such as routeing or areas to be avoided, adopted under other instruments. An emission control area is an Annex VI designation controlling SOx, particulate matter or NOx emissions to air.

Do Annex I and Annex V use the same list of special areas?

No. Annex V lists eight special areas: the Mediterranean, Baltic, Black Sea, Red Sea, Gulfs area, North Sea, Antarctic area and Wider Caribbean Region.

The Gulf of Aden, North West European waters, Oman area and Southern South African waters are Annex I areas only. Annex II has one special area, the Antarctic, and Annex IV has one, the Baltic Sea.

Does US law recognize all ten Annex I special areas?

33 CFR 151.13(a) lists all ten but states that discharge restrictions are effective only in the Mediterranean, Baltic, Black Sea and Antarctic area.

Paragraph (h) still refers to Regulation 38.6.1 and to Federal Register notice of later dates. The section was last amended in 2015, so it does not reflect the 1999, 2008 and 2025 effect dates fixed by MEPC.

Which document is the authoritative list of special areas and their effect dates?

The MARPOL text (Annex I Reg 1.11) defines the areas; the IMO Secretariat circular MEPC.1/Circ.778 tabulates adoption, entry-into-force and in-effect dates for every MARPOL special area and emission control area.

Revision 4 was issued on 30 October 2023 and Revision 5 on 9 May 2025.

Can a ship trading only inside special areas skip the oily water separator?

Reg 14.5 allows the Administration to waive the Reg 14.1 and 14.2 equipment for a ship engaged exclusively on voyages within special areas or Arctic waters, provided it has a holding tank for all oily bilge water, discharges to reception facilities, has its IOPP Certificate endorsed and records the discharges in the Oil Record Book.

A high-speed craft on a scheduled service of no more than 24 hours qualifies on the same terms.

Can small island developing States meet the special-area reception duty through regional arrangements?

Yes.

MEPC.216(63), in force 1 August 2013, allowed small island developing States to meet Reg 38 reception-facility requirements through regional arrangements under a Regional Reception Facilities Plan, and MEPC.359(79), in force 1 May 2024, extended regional arrangements to States bordering Arctic waters for ports within Arctic waters.

Sources

  1. IMO Resolution MEPC.117(52) (15 October 2004). revised MARPOL Annex I, Regulations 1.11, 15, 34 and 38 imo.org
  2. IMO Resolution MEPC.154(55) (13 October 2006). designation of the Southern South African waters as a Special Area imo.org
  3. IMO Resolution MEPC.29(25) (1 December 1987). designation of the Gulf of Aden as a Special Area imo.org
  4. IMO Resolution MEPC.42(30) (16 November 1990). designation of the Antarctic area as a special area under Annexes I and V imo.org
  5. IMO Resolution MEPC.75(40) (25 September 1997). Annex I amendments designating North West European waters imo.org
  6. IMO Resolution MEPC.77(41) (2 April 1998). date on which the North West European waters special area requirements take effect imo.org
  7. IMO Resolution MEPC.167(56) (13 July 2007). effect date for the Southern South African waters special area imo.org
  8. IMO Resolution MEPC.168(56) (13 July 2007). effect date for the Gulfs area special area under Annexes I and V imo.org
  9. IMO Resolution MEPC.381(80) (7 July 2023). date on which Regulations 15.3, 15.5 and 34.3 to 34.5 take effect for the Red Sea and Gulf of Aden special areas imo.org
  10. IMO Resolution MEPC.189(60) (26 March 2010). new Annex I Chapter 9, Regulation 43, oils in the Antarctic area imo.org
  11. IMO Resolution MEPC.329(76) (17 June 2021). Annex I Regulation 43A, heavy fuel oil in Arctic waters imo.org
  12. IMO Resolution MEPC.265(68) (15 May 2015). MARPOL amendments making the Polar Code environmental provisions mandatory imo.org
  13. IMO Resolution MEPC.187(59) (17 July 2009). Annex I amendments, IOPP Supplement and Oil Record Book Parts I and II imo.org
  14. IMO Resolution MEPC.382(80) (7 July 2023). date on which the Annex V special area requirements take effect for the Red Sea imo.org
  15. IMO Resolution MEPC.216(63) (2 March 2012). regional reception facility arrangements for small island developing States imo.org
  16. IMO Resolution MEPC.359(79) (16 December 2022). regional reception facilities within Arctic waters imo.org
  17. IMO Resolution A.1087(28) (4 December 2013). 2013 Guidelines for the Designation of Special Areas under MARPOL imo.org
  18. IMO Resolution A.982(24) (1 December 2005). Revised Guidelines for the Identification and Designation of Particularly Sensitive Sea Areas imo.org
  19. IMO MEPC.1/Circ.778/Rev.4 (30 October 2023). Special Areas and Emission Control Areas under MARPOL imo.org
  20. 33 CFR Part 151, including 151.06 (special area definitions) and 151.13 (special areas for Annex I) ecfr.gov