Polar Code: Rules for Ships in Arctic and Antarctic Waters
The Polar Code is the mandatory IMO code for ships in Arctic and Antarctic waters: categories A to C, Polar Ship Certificate, PWOM, POLARIS and MARPOL rules.
Contents21 sections
The International Code for Ships Operating in Polar Waters, the Polar Code, is the mandatory IMO code that sets additional safety and pollution-prevention requirements for ships operating in Arctic waters and in the Antarctic area south of 60°S. The Maritime Safety Committee adopted its safety parts by MSC.385(94) on 21 November 2014 and the Marine Environment Protection Committee adopted its environmental parts by MEPC.264(68) on 15 May 2015. It took effect on 1 January 2017 through a new SOLAS Chapter XIV and amendments to four MARPOL annexes.
The Code adds to the general conventions and does not replace them. A polar ship still complies with SOLAS, MARPOL, the STCW Convention and its class rules, and then meets the polar layer on top: a ship category, a Polar Ship Certificate, a Polar Water Operational Manual, a polar service temperature, a defined ice capability and zero-discharge rules in the Arctic. Since 1 January 2026 parts of the Code also reach fishing vessels, pleasure yachts and small cargo ships that SOLAS never covered before.
What the Polar Code is and how it became mandatory
The Polar Code is a single IMO code made mandatory by two conventions at once: its safety part through SOLAS chapter XIV and its environmental part through MARPOL Annexes I, II, IV and V. Both vehicles entered into force on 1 January 2017.
Structure: Parts I-A, I-B, II-A and II-B
The Code has an Introduction and two parts, each split into a mandatory section and a recommendatory one. The Introduction sets the definitions, the three ship categories and the ten hazard sources that the rest of the Code addresses.
| Part | Content | Status | Made mandatory by |
|---|---|---|---|
| Introduction | Definitions, categories, hazards | Mandatory where referenced | SOLAS XIV/3 and the MARPOL polar chapters |
| I-A | Safety measures, chapters 1 to 12 plus 9-1 and 11-1 | Mandatory | SOLAS chapter XIV |
| I-B | Guidance on the Part I-A provisions | Recommendatory | Not mandatory |
| II-A | Pollution prevention measures, chapters 1 to 5 | Mandatory | MARPOL Annexes I, II, IV and V |
| II-B | Guidance on pollution prevention | Recommendatory | Not mandatory |
Each Part I-A chapter follows a goal-based pattern: a goal, functional requirements that serve the goal, and regulations that satisfy the functional requirements. A ship may meet a functional requirement by an alternative design only for chapters 3, 6, 7 and 8, and SOLAS XIV/4 requires that alternative to be recorded on the Polar Ship Certificate and in the PWOM.
The ten hazard sources in Introduction paragraph 3.1 are ice, topside icing, low temperature, extended darkness or daylight, high latitude, remoteness and limited hydrographic data, crew inexperience, lack of emergency response equipment, rapidly changing weather, and environmental sensitivity. Every chapter of Part I-A traces back to one or more of them.
Adoption and entry into force
The adoption sequence ran across two committees and six months, which is why the Code carries two resolution numbers.
- 21 November 2014. The Maritime Safety Committee adopted MSC.385(94) (the safety-related Introduction and Parts I-A and I-B) and MSC.386(94), which added SOLAS chapter XIV, “Safety measures for ships operating in polar waters”, regulations 1 to 4.
- 15 May 2015. The Marine Environment Protection Committee adopted MEPC.264(68) (the environment-related Introduction and Parts II-A and II-B) and MEPC.265(68), which amended MARPOL.
- 1 July 2016. Both amending resolutions were deemed accepted under tacit acceptance.
- 1 January 2017. SOLAS chapter XIV and the MARPOL amendments entered into force, and the Code took effect.
- 1 January 2018. Ships built before 2017 became due at their first intermediate or renewal survey after this date.
- 1 July 2018. STCW polar training became mandatory.
- 1 January 2026. MSC.532(107) and MSC.538(107) extended chapters 9-1 and 11-1 to non-SOLAS ships.
MEPC.265(68) placed the polar pollution rules in four new MARPOL chapters: Annex I chapter 11 (regulations 46 and 47), Annex II chapter 10 (regulations 21 and 22), Annex IV chapter 7 (regulations 17 and 18) and Annex V chapter 3 (regulations 13 and 14). Annex III, on harmful substances in packaged form, was not amended, and Part II-A chapter 3 is “kept blank intentionally”.
Before 2017 the IMO position was voluntary guidance, most recently Assembly resolution A.1024(26), Guidelines for ships operating in polar waters, adopted in 2009. The Code converted that guidance into mandatory text for SOLAS and MARPOL ships.
Application: which ships and which waters
The Polar Code applies to a ship by reference to where it operates and which convention certifies it. Polar waters are Arctic waters plus the Antarctic area (SOLAS XIV/1.4); the ship’s convention status decides which parts bind it.
Arctic waters and the Antarctic area
The Antarctic area is the sea area south of latitude 60°S (SOLAS XIV/1.2). That matches the Antarctic Treaty area and the MARPOL Antarctic special area, discussed in the Antarctic special area article.
Arctic waters are defined by a boundary line, not by the Arctic Circle at about 66°33’N. SOLAS XIV/1.3 draws the line from 58°00’.0N 042°00’.0W through 64°37’.0N 035°27’.0W, 67°03’.9N 026°33’.4W and 70°49’.56N 008°59’.61W, past the southern shore of Jan Mayen, to 73°31’.6N 019°01’.0E at Bjørnøya, then by great circle to Cap Kanin Nos at 68°38’.29N 043°23’.08E. From there it follows the northern shore of the Asian continent east to the Bering Strait, runs west to 60°N as far as Il’pyrskiy, follows the 60th parallel east to and including Etolin Strait, then the northern shore of North America south to 60°N, and finally runs east along 60°N to 056°37’.1W and back to the starting point.
The line has two practical consequences. The Norwegian mainland coast and Iceland sit outside Arctic waters even though both lie partly north of the Arctic Circle. Northern Hudson Bay and the waters west of Greenland down to 60°N sit inside, although they are south of it. MARPOL uses the same coordinates for the Part II-A Arctic rules.
SOLAS ships
SOLAS XIV/2.1.1 applies the chapter to ships operating in polar waters that are “certified in accordance with chapter I”. In practice that means passenger ships of any size and cargo ships of 500 GT and upwards on international voyages, the population that holds SOLAS safety certificates; SOLAS Chapter I sets the exclusions. Government ships operated for non-commercial purposes are excluded, though they are encouraged to act consistently with the chapter.
These ships comply with the safety-related Introduction and all of Part I-A, and are surveyed and certificated under SOLAS I/7 to I/10 (SOLAS XIV/3).
Non-SOLAS ships since 1 January 2026
MSC.532(107), adopted 8 June 2023 and in force 1 January 2026, rewrote SOLAS XIV/2.1 to add three classes of ship that SOLAS chapter I does not certificate:
- fishing vessels of 24 m in length overall and above;
- pleasure yachts of 300 GT and upwards not engaged in trade; and
- cargo ships of 300 GT and upwards but below 500 GT.
Under the new regulation XIV/3-1 these ships comply only with Part I-A chapters 9-1 (safety of navigation) and 11-1 (voyage planning), read with the Introduction and paragraphs 1.2, 1.4 and 1.5. They do so on every voyage in the Antarctic area and on Arctic voyages beyond the outer limit of their flag State’s territorial sea, so a Norwegian fishing vessel working inside the territorial sea around Svalbard is outside the rule, while the same vessel fishing beyond it is inside. No Polar Ship Certificate is required for them.
Ships in these three classes constructed before 1 January 2026 must comply by 1 January 2027 (SOLAS XIV/2.3). That is a calendar date, not the first survey after it.
Two recommendatory circulars sit behind the extension: MSC.1/Circ.1641 for fishing vessels of 24 m and over and MSC.1/Circ.1642 for pleasure yachts of 300 GT and above, both of 14 May 2021. The port State control regime for fishing vessels is a separate matter.
Existing ships and compliance dates
A SOLAS ship constructed before 1 January 2017 had to meet the relevant Part I-A requirements by its first intermediate or renewal survey, whichever came first, after 1 January 2018 (SOLAS XIV/2.2). Several Part I-A provisions apply only to ships constructed on or after 1 January 2017, so an older ship can hold a valid Polar Ship Certificate without, for example, damage stability against ice penetration or enclosed bridge wings. Each such date-limited rule is identified where it arises below.
Ship categories A, B and C
Every SOLAS ship under the Code is assigned one of three categories, which describe the ice it is designed for. The definitions are in Introduction paragraphs 2.1 to 2.3 and use the WMO Sea Ice Nomenclature.
| Category | Designed for | Ice thickness reference | Structural reference (Part I-A 3.3.2) |
|---|---|---|---|
| A | At least medium first-year ice, which may include old ice inclusions | Medium first-year ice 70 to 120 cm | IACS Polar Class PC1 to PC5, or equivalent |
| B | Not Category A; at least thin first-year ice, which may include old ice inclusions | Thin first-year ice 30 to 70 cm | IACS Polar Class PC6 to PC7, or equivalent |
| C | Open water or ice conditions less severe than A and B | Below thin first-year ice | Ice strengthening not required if the Administration finds the structure adequate |
Open water means sea ice concentration below 1/10 with no ice of land origin; bergy water means ice of land origin below 1/10 with total ice not over 1/10. First-year ice runs from 0.3 m to 2.0 m, and old ice is ice that has survived at least one summer’s melt.
The category drives several other requirements. Damage stability against ice penetration, enclosed bridge wings, the 0.76 m fuel tank separation and the treated-sewage-only rule all apply to Category A and B ships built from 2017 and not to Category C, except that the sewage rule also binds every passenger ship built from 2017 whatever its category. The category is a design statement, so a Category C ship that meets heavier ice than its certificate allows is outside its approved limitations, whatever its engine power.
Hazards, operational assessment and the polar service temperature
The Code requires each SOLAS ship to be assessed against its intended operations before it is certificated. Part I-A paragraph 1.5 requires an operational assessment covering operation in low air temperature, in ice, at high latitude, and the possibility of abandonment onto ice or land, plus the Introduction 3 hazards that apply.
The polar service temperature (PST) is the reference temperature for equipment and systems. Paragraph 1.2.11 sets it at least 10°C below the lowest mean daily low temperature (MDLT) for the intended area and season, and paragraph 1.2.9 defines MDLT as the mean of the daily low temperature for each day of the year over a period of at least 10 years. A ship intended to operate where the lowest MDLT is below -10°C is a ship intended to operate in low air temperature (paragraph 1.2.12), and needs a PST.
Take a ship planning autumn voyages where the lowest MDLT on its route is -18°C. Its PST is -28°C or colder, and paragraph 1.4.2 requires its systems and equipment to be fully functional at that temperature. Paragraph 1.4.3 requires survival systems and equipment to be fully operational at the PST throughout the maximum expected time of rescue.
The maximum expected time of rescue is defined in paragraph 1.2.7 and “shall never be less than 5 days”. It is the period for which life-saving appliances, survival kits and survival-craft communications must keep people alive, and five days is a floor, not a target: paragraph 1.2.7 sets no upper figure. See the search and rescue article for how rescue coordination works in remote areas.
Polar Ship Certificate
Every SOLAS ship to which the Code applies carries a valid Polar Ship Certificate (Part I-A paragraph 1.3.1). It is issued after an initial or renewal survey by the Administration or by a recognized organization acting under SOLAS XI-1/1 (paragraphs 1.3.2 and 1.3.4), in the model form at appendix 1 of the Code.
The certificate records the ship category, the ice class, the polar service temperature where one applies, any alternative design under SOLAS XIV/4, and a reference to the methodology used to assess the ship’s operational capabilities and limitations in ice (paragraph 1.3.7). That last entry is where POLARIS, or an equivalent method, enters the certificate.
Validity is harmonized with the other SOLAS certificates under regulation I/14 (paragraph 1.3.6), so the Polar Ship Certificate runs on the same survey cycle as the ship’s safety certificates. For a Category C cargo ship, paragraph 1.3.3 lets the Administration issue the certificate on documented verification, without an initial onboard survey, where the operational assessment finds no additional equipment or structural modification is needed. An onboard survey then follows at the next scheduled survey.
The certificate is distinct from the ship’s class notation. A classification society assigns a Polar Class or another ice class under its rules; the Polar Ship Certificate is a statutory document under SOLAS chapter XIV, even when the same society issues both on the flag’s behalf.
Polar Water Operational Manual
The Polar Water Operational Manual (PWOM), required by Part I-A chapter 2, gives the owner, operator, master and crew the ship’s specific operational capabilities and limitations in polar waters. It is carried on board and written for that ship, not for the fleet.
Three items from elsewhere in the Code have to be written into it. The ice operational assessment from paragraph 1.5 and its methodology, which for most ships is POLARIS, define where and at what speed the ship may go. MSC.1/Circ.1519 paragraph 1.4.4 puts the POLARIS elevated-risk speed limits in the PWOM. Any alternative design approved under SOLAS XIV/4 is recorded there as well as on the certificate.
The PWOM sits alongside the safety management system under the ISM Code rather than inside it, although most operators cross-reference the two so that polar procedures (cold-weather start-up, ice watch, escort operations, emergency response in remote areas) are drilled and audited through the SMS. Part I-B gives the model contents.
Operational limitations in ice: POLARIS
POLARIS, the Polar Operational Limit Assessment Risk Indexing System, is the IMO methodology for assessing a ship’s operational limitations in ice. It is set out in MSC.1/Circ.1519, “Guidance on methodologies for assessing operational capabilities and limitations in ice”, of 6 June 2016, and it is the method Part I-A paragraph 1.3.7 anticipated when the Code was adopted.
The method computes a Risk Index Outcome (RIO) for the ice regime the ship faces. Each ice type present is assigned a Risk Index Value (RIV) that depends on the ship’s ice class, and the RIO is the sum of each ice type’s concentration in tenths multiplied by its RIV.
Risk Index Outcome
where
| \(C_i\) | Concentration of ice type i | tenths |
| \(RIV_i\) | Risk Index Value (Ice Class vs type) |
Concentrations are entered in tenths and sum to 10, the ice-free fraction included. RIV values come from Table 1.3 of the circular, with 12 ice-class rows (PC1 to PC7, the Finnish-Swedish classes IA Super, IA, IB and IC, and not ice-strengthened) against 12 ice types from ice-free to heavy multi-year ice; Table 1.4 gives decayed-ice values for the melt season. Ice-free water scores RIV 3 for every class. Heavy multi-year ice scores +1 for PC1 and -8 for a ship that is not ice-strengthened.
| RIO | Polar Class PC1 to PC7 | Below PC7 or no ice class |
|---|---|---|
| 0 or above | Normal operation | Normal operation |
| -10 to below 0 | Elevated operational risk | Operation subject to special consideration |
| Below -10 | Operation subject to special consideration | Operation subject to special consideration |
For a Polar Class ship in the elevated-risk band, Table 1.2 recommends speed limits of 11 knots for PC1, 8 knots for PC2, 5 knots for PC3 to PC5 and 3 knots below PC5. A ship below PC7 has no elevated-risk band at all: any negative RIO puts it in special consideration.
POLARIS is guidance, not a Code regulation. The Code requires a methodology to be referenced on the certificate; POLARIS is the one IMO developed, and Canada mandates it as one of its entry tests under SOR/2017-286 section 8(2)(b). The ice concentrations and stages of development that go into the calculation come from ice charts, which is why Part I-A chapter 9 requires ships to receive and display current ice information.
Structure, Polar Class and other ice classes
Part I-A chapter 3 requires a polar ship’s structure to withstand the global and local effects of its anticipated environmental conditions. The Code sets the standard by footnote rather than by its own scantling rules.
Paragraph 3.3.2 has the scantlings of a Category A ship approved taking into account IACS Polar Class PC1 to PC5, and of a Category B ship PC6 or PC7, “or other standards offering an equivalent level of safety”. An ice-strengthened Category C ship follows standards adequate for the ice types it will meet. A Category C ship need not be ice strengthened at all where the Administration finds its structure adequate for the intended operation. Material grades for exposed structure are chosen for the PST, with IACS UR S6 or UR I named in the footnote.
IACS Polar Class PC1 to PC7
The International Association of Classification Societies defines the seven Polar Classes in three Unified Requirements. Each UR revision applies by contract date, not by the date of certification, so two sister ships contracted either side of a cut-off can be built to different texts.
| UR | Subject | Current revision | Applies to ships contracted |
|---|---|---|---|
| UR I1 | Polar Class descriptions and application | Rev.2, April 2016 | On or after 1 July 2017 |
| UR I2 | Structural requirements for Polar Class ships | Rev.4, December 2019; Rev.5, June 2025 | Rev.4 from 1 January 2021; Rev.5 from 1 January 2027 |
| UR I3 | Machinery requirements for Polar Class ships | Rev.2, January 2023, Corr.1 December 2024 | On or after 1 July 2024 |
UR I1 Table 1 describes the classes by intended ice and season:
| Polar Class | Ice description (UR I1 Table 1) | Polar Code category reference |
|---|---|---|
| PC1 | Year-round operation in all polar waters | A |
| PC2 | Year-round operation in moderate multi-year ice conditions | A |
| PC3 | Year-round operation in second-year ice which may include multi-year ice inclusions | A |
| PC4 | Year-round operation in thick first-year ice which may include old ice inclusions | A |
| PC5 | Year-round operation in medium first-year ice which may include old ice inclusions | A |
| PC6 | Summer/autumn operation in medium first-year ice which may include old ice inclusions | B |
| PC7 | Summer/autumn operation in thin first-year ice which may include old ice inclusions | B |
UR I1 makes the owner responsible for selecting the Polar Class, assigns the lower class where hull and machinery differ, and provides an additional “Icebreaker” notation. For the wider family of class notations see ice class notations.
Finnish-Swedish ice classes and equivalency
The Finnish-Swedish Ice Class Rules define classes IA Super, IA, IB and IC for Baltic winter navigation. The current Finnish regulation is “Ice Class Regulations and the Application Thereof”, TRAFICOM/68863/03.04.01.00/2021, valid from 5 July 2021, with a separate equivalence regulation on class notations, TRAFICOM/281964/03.04.01.00/2023, valid from 1 January 2025.
The Polar Code contains no automatic mapping from these classes to its categories. A Baltic ice class reaches Category A or B only through the equivalency method in Part I-B section 4: the owner or operator compares the ship’s ice class with an IACS Polar Class, the flag Administration or its recognized organization approves the equivalency, and the result is noted on the Polar Ship Certificate. Without that approval an IA Super ship is Category C, however capable it is in Baltic first-year ice. POLARIS treats IA Super to IC as below PC7 in Table 1.1.
Stability, subdivision, machinery and fire safety
The Code adds polar loads to the stability and integrity rules of SOLAS Chapter II-1 and requires machinery and fire systems to work at the polar service temperature.
Intact stability with icing (Part I-A paragraph 4.3.1). Ships operating in areas and periods where ice accretion is likely must include icing in their intact stability calculations: 30 kg/m2 on exposed weather decks and gangways and 7.5 kg/m2 on the projected lateral area of each side above the water plane. Discontinuous surfaces such as rails and rigging are allowed for by increasing the continuous lateral area by 5% and its static moment by 10%. See ice accretion and the icing allowance.
Damage stability against ice (paragraph 4.3.2). Category A and B ships constructed on or after 1 January 2017 must survive flooding from ice damage with an assumed penetration extent of 760 mm, with the survival factor s equal to 1. Category C ships and ships built before 2017 carry no such requirement. The general method is covered in damage stability.
Watertight and weathertight integrity (chapter 5). Paragraph 5.3 requires means to remove or prevent ice and snow accumulation around hatches and doors on ships likely to meet ice accretion, protection of hydraulic fluid in closing arrangements on ships intended to operate in low air temperature, and closing devices that crew in heavy winter clothing, thick mittens included, can operate.
Machinery (chapter 6) and fire safety (chapter 7). Both chapters name the PST directly: machinery installations and fire safety systems and appliances must be operable at the polar service temperature and protected against ice accretion, snow and low air temperature. IACS UR I3 sets the machinery requirements for Polar Class ships. Chapters 6 and 7 are two of the four for which SOLAS XIV/4 allows an alternative design; chapter 5 is not.
Navigation, voyage planning and communications
Part I-A chapters 9, 10 and 11 add polar equipment and planning to SOLAS Chapter V and SOLAS Chapter IV. MSC.538(107) retitled chapters 9 and 11 to cover ships certified under SOLAS chapter I and added parallel chapters 9-1 and 11-1 for the non-SOLAS ships.
Chapter 9 equipment for SOLAS ships
- Ice information. The ship must be able to receive and display current information on ice conditions in its area of operation.
- Depth sounding. Ice-strengthened ships constructed on or after 1 January 2017 have either two independent echo-sounding devices or one echo-sounder with two separate independent transducers (paragraph 9.3.2.1.1).
- Heading. Two independent non-magnetic means of determining and displaying heading, connected to main and emergency power (paragraph 9.3.2.2.1). A magnetic compass becomes unreliable near the magnetic pole and a gyrocompass loses accuracy at high latitude.
- Antennas and sensors. Ships likely to meet ice accretion have means to prevent ice build-up on antennas needed for navigation and communication (paragraph 9.3.2.1.3), and ice-strengthened ships built from 2017 protect sensors that project below the hull against ice (paragraph 9.3.2.1.4.1).
- High latitude. Ships proceeding above 80° latitude carry at least one GNSS compass or equivalent (paragraph 9.3.2.2.2).
- Searchlights. Two remotely rotatable narrow-beam searchlights controllable from the bridge, or other means to visually detect ice, covering a 360-degree arc, except for ships operating solely in 24-hour daylight (paragraph 9.3.3.1).
- Bridge wings. Category A and B ships constructed on or after 1 January 2017 have enclosed or protected bridge wings (paragraph 9.3.2.1.4.2).
- Escort light. Ships involved in icebreaker-assisted operations carry a manually initiated flashing red light visible astern, to indicate when the ship is stopped, with the arcs of a COLREG stern light and a range of at least 2 nautical miles (paragraph 9.3.3.2).
The Code does not add a radar. A second radar comes from SOLAS V/19.2.7 for ships of 3,000 GT and upwards, independent of trading area; Part I-B only recommends radars with enhanced ice detection. Chapter 9-1 for non-SOLAS ships carries a lighter set: ice information, two echo-sounders or transducers on ice-strengthened ships built from 2026 (with fish finders acceptable as an equivalent), two non-magnetic heading means for ships of 500 GT and upwards, and two means of illumination for ice detection.
Voyage planning (chapter 11)
Paragraph 11.3 lists what a polar voyage plan must take into account:
- the procedures required by the PWOM;
- any limitations of the hydrographic information and aids to navigation available;
- current information on the extent and type of ice and icebergs near the intended route;
- statistical information on ice and temperatures from former years;
- places of refuge;
- current information and measures for areas with marine mammals, including seasonal migration areas;
- relevant ships’ routing systems, speed recommendations and vessel traffic services for marine mammal areas;
- national and international designated protected areas along the route; and
- operation in areas remote from search and rescue capabilities.
Chapter 11-1 applies the same goal to the non-SOLAS ships. The marine-mammal and protected-area items connect the plan to particularly sensitive sea areas and national reserves.
Communications (chapter 10)
Chapter 10 requires communication that works at high latitude, where geostationary satellite coverage fades. Ships must have ship-to-ship and ship-to-shore communication that accounts for those limits, two-way voice and data communication with a rescue coordination centre, voice communication with aircraft on 121.5 MHz and 123.1 MHz, and two-way voice and data with telemedical assistance services. Ships intended to provide icebreaker escort carry a sound signalling system facing astern.
Lifeboats and rescue boats on ships intended to operate in low air temperature carry a device for distress alerting, a means of being located and a means of on-scene communication; other survival craft carry the locating and on-scene devices. Battery-powered equipment must be managed so it lasts the maximum expected time of rescue. The GMDSS overview covers the sea-area system these requirements build on.
Life-saving appliances and survival
Part I-A chapter 8 sizes life-saving appliances to the polar service temperature and to a maximum expected time of rescue of at least five days, on top of the LSA Code and SOLAS Chapter III.
On passenger ships, paragraph 8.3.3.1 requires an immersion suit or a thermal protective aid for each person on board, and where immersion suits are required they are of the insulated type. Paragraph 8.3.3.3 requires personal and group survival equipment, and Part I-B sections 9.1 and 9.2 give sample contents for the personal and group survival kits.
Paragraph 1.4.3 requires survival systems and equipment, including survival craft and their launching arrangements, to be fully operational at the PST throughout the maximum expected time of rescue. Chapter 8 is goal-based, so the kit list for a given ship comes out of its operational assessment and is recorded in the PWOM rather than read from one table in the Code.
Manning and STCW polar training
Part I-A chapter 12 requires masters, chief mates and officers in charge of a navigational watch on polar ships to hold polar training certificates, and the STCW Convention defines those certificates. The requirement depends on the ice the ship will meet and the type of ship.
| Ice conditions | Tankers | Passenger ships | Other ships |
|---|---|---|---|
| Ice-free | Not applicable | Not applicable | Not applicable |
| Open waters | Basic training for master, chief mate and OOW | Basic training for master, chief mate and OOW | Not applicable |
| Other waters | Advanced for master and chief mate; basic for OOW | Advanced for master and chief mate; basic for OOW | Advanced for master and chief mate; basic for OOW |
Paragraph 12.3.2 lets the Administration allow a person other than the master or chief mate, qualified under STCW II/2 and section A-II/2 and holding advanced polar training, to meet the advanced requirement, which is how ice navigators are carried on some ships.
The certificates come from STCW regulation V/4, added by MSC.416(97), and section A-V/4 of the STCW Code, added by MSC.417(97). Both were adopted on 25 November 2016 and entered into force on 1 July 2018. The basic certificate requires approved training meeting A-V/4 paragraph 1 (Table A-V/4-1). The advanced certificate requires the basic certificate, at least two months of approved seagoing service in the deck department within polar waters (at management level or while performing watchkeeping at operational level) or equivalent approved service, and training meeting A-V/4 paragraph 2 (Table A-V/4-2). Both certificates are revalidated at intervals not exceeding five years under STCW I/11.
Between 1 January 2017 and 1 July 2018 the Code applied with recommendatory guidance in STCW Code section B-V/g. Transitional provisions in V/4.6 and V/4.7 let seafarers who began polar service before 1 July 2018 qualify by service or approved courses until 1 July 2020. STCW Chapter V covers the regulation in detail, and masters and deck officers covers the underlying certificates of competency.
Pollution prevention: Part II-A
Part II-A applies to ships under each MARPOL annex it amends, so its reach follows the annex: Annex I rules bind any ship to which Annex I applies, and so on. Most of the operative restrictions are Arctic-only, because the Antarctic area already carried special-area status under Annexes I, II and V before 2017.
Oil
Part II-A paragraph 1.1.1 prohibits “any discharge into the sea of oil or oily mixtures from any ship” in Arctic waters. Clean or segregated ballast is excepted (paragraph 1.1.2). The Arctic is not a MARPOL Annex I special area; the zero-discharge rule comes from the Polar Code through Annex I chapter 11, and it is stricter than the 15 ppm special-area regime, so the oily water separator is not a route to overboard discharge in the Arctic. In the Antarctic area, MARPOL Annex I regulation 15.4 already prohibits oil discharge.
Paragraph 1.2 sets structural separation for Category A and B ships constructed on or after 1 January 2017:
- Fuel tanks. Ships with an aggregate oil fuel capacity below 600 m3 keep all oil fuel tanks at least 0.76 m from the outer shell; tanks of 30 m3 or less are excepted (paragraph 1.2.1). Larger ships are already covered by MARPOL Annex I regulation 12A.
- Cargo oil on non-tankers. Cargo tanks for oil on ships other than oil tankers are also 0.76 m from the shell (paragraph 1.2.2).
- Small tankers. Oil tankers below 5,000 tonnes deadweight have double bottom and wing tank protection to Annex I regulations 19.6.1, 19.3.1 and 19.6.2 (paragraph 1.2.3).
- Sludge and bilge tanks. Oil residue and oily bilge water holding tanks are 0.76 m from the shell, with the same 30 m3 exception (paragraph 1.2.4).
Paragraph 1.1.4 requires polar operations to be taken into account in the Oil Record Book, the manuals and the shipboard oil pollution emergency plan.
Paragraph 1.1.3 allowed Category A ships built before 2017 that operate continuously in Arctic waters for more than 30 days, and cannot comply with the zero-discharge rule for oil or oily mixtures from machinery spaces, a limited transition with Administration approval to the first intermediate or renewal survey one year after 1 January 2017; until then they followed Annex I regulation 15.3.
Heavy fuel oil is not banned by the Polar Code. Part II-B paragraph 1.1 only encourages applying MARPOL Annex I regulation 43 in Arctic waters. The Arctic ban is MARPOL Annex I regulation 43A, added by MEPC.329(76) of 17 June 2021, in force 1 November 2022 and applying from 1 July 2024. Ships with protected fuel tanks under regulation 12A or Part II-A paragraph 1.2.1 are exempt until 1 July 2029, and a Party bordering Arctic waters may temporarily waive the rule for ships under its flag in waters under its sovereignty or jurisdiction, with no waiver applying on or after 1 July 2029. The regulation 43A article covers it, and heavy fuel oil covers the fuel. In the Antarctic, regulation 43, added by MEPC.189(60), has prohibited the use and carriage of heavy grade oil since 1 August 2011.
Noxious liquid substances
Part II-A paragraph 2.1.1, through MARPOL Annex II chapter 10, prohibits any discharge of noxious liquid substances or mixtures containing them in Arctic waters. Paragraph 2.1.3 makes carriage of ship type 3 products (IBC Code chapter 17) or chapter 18 products in type 3 cargo tanks on Category A and B ships built from 2017 subject to Administration approval, recorded on the NLS certificate or the IBC Code Certificate of Fitness. Chapter 3 of Part II-A, on harmful substances in packaged form, is intentionally blank.
Sewage
Part II-A chapter 4 is made mandatory by MARPOL Annex IV chapter 7, and its distances are measured from the nearest ice shelf or fast ice as well as from land. Comminuted and disinfected sewage may be discharged at more than 3 nautical miles and untreated sewage at more than 12 nautical miles from any ice shelf or fast ice, in both cases as far as practicable from areas of ice concentration exceeding 1/10, under the conditions of Annex IV regulation 11 (paragraph 4.2.1). Category A and B ships and passenger ships constructed on or after 1 January 2017 may discharge only sewage treated by an approved sewage treatment plant (paragraph 4.2.2). Category A and B ships operating for extended periods in ice concentrations above 1/10 may discharge only through an approved treatment plant, with Administration approval (paragraph 4.2.3).
Garbage
Part II-A chapter 5, through MARPOL Annex V chapter 3, adds to the general garbage discharge rules.
In Arctic waters, on top of Annex V regulation 4 (paragraph 5.2.1):
- food waste is discharged as far as practicable from areas of ice concentration above 1/10, and in any case at least 12 nautical miles from the nearest land, ice shelf or fast ice;
- it is comminuted to pass a 25 mm screen and is not contaminated by other garbage;
- it is not discharged onto the ice;
- discharge of animal carcasses is prohibited; and
- cargo residues that cannot be recovered may be discharged only en route, and only where they are not harmful to the marine environment, both departure and destination ports are within Arctic waters with no transit outside them, no adequate reception facilities exist at those ports, and the discharge is at least 12 nautical miles from land, ice shelf or fast ice.
In the Antarctic area, on top of Annex V regulation 6, discharges permitted by regulation 6.1 are made at least 12 nautical miles from the nearest fast ice, and food waste is not discharged onto the ice (paragraph 5.2.2). Hold washing in Arctic trades is covered in cargo residues and hold washings.
Part II-B recommendations
Part II-B is guidance. Paragraph 1.1 encourages applying Annex I regulation 43 (the Antarctic heavy grade oil rule) in Arctic waters, and paragraph 1.2 encourages non-toxic biodegradable lubricants or water-based systems in components outside the hull that are in contact with seawater. Part II-B section 4 addresses ballast water, written before the Ballast Water Management Convention entered into force, and biofouling by reference to the 2011 Biofouling Guidelines, MEPC.207(62). The 2023 Biofouling Guidelines, MEPC.378(80), postdate the Code text and are not referenced in it; a biofouling management plan under them is the current practice.
Regional overlays
The Polar Code is the international baseline. Coastal States with Arctic jurisdiction and the Antarctic Treaty Parties add rules on top of it, and a ship trading in their waters meets both.
Canada
Canada’s Arctic Shipping Safety and Pollution Prevention Regulations, SOR/2017-286, made under the Arctic Waters Pollution Prevention Act and the Canada Shipping Act, 2001, were registered and entered into force on 19 December 2017. They define the Polar Code as MSC.385(94) and MEPC.264(68), require Canadian ships in polar waters and foreign ships in a shipping safety control zone to conform to SOLAS chapter XIV, and read “should” in incorporated documents as “must” (section 2(2)), so recommendatory wording in the incorporated Code provisions binds ships in Canadian Arctic waters.
Entry to a control zone needs one of four routes under section 8: the Zone/Date system in Schedule 1; the Arctic Ice Regime Shipping System (AIRSS) with an ice numeral of zero or more, for ships built before 1 January 2017 other than Polar Class ships; POLARIS showing normal operation; or, for PC3 to PC7 ships, operation at elevated risk with PWOM mitigation. Section 10 requires an ice navigator on some ships outside Type E periods, qualified by 50 days of ice experience (30 of them in Arctic waters) or an STCW V/4 advanced polar certificate. Section 14 allows no oil deposit beyond minimal unavoidable leakage from underwater machinery, and sections 19 to 22 set Canadian sewage rules. The regulations repealed the older Arctic Shipping Pollution Prevention Regulations. See Canada’s Arctic shipping pollution prevention regime.
Antarctic Treaty system
The Antarctic Treaty and the Madrid Protocol govern activities south of 60°S alongside the Polar Code. Two Treaty instruments directly relevant to shipping remain unapproved:
- Measure 4 (2004), “Insurance and contingency planning for tourism and non-governmental activities in the Antarctic Treaty area”, adopted at ATCM XXVII in Cape Town. The Antarctic Treaty Secretariat lists it as not yet effective, with 17 of 27 required approvals recorded on 15 October 2026. See Antarctic Treaty Measure 4 (2004).
- Annex VI to the Madrid Protocol, “Liability arising from environmental emergencies”, adopted by Measure 1 (2005) at ATCM XXVIII in Stockholm. It becomes effective only when every Consultative Party entitled to attend ATCM XXVIII has approved it; 19 of 28 required approvals were recorded on 15 October 2026. See Madrid Protocol Annex VI.
Russia and Norway
Russia administers navigation in the water area of the Northern Sea Route under its own rules and a permit system, applied in addition to the Polar Code to ships transiting its Arctic coast. Norway restricts heavy fuel oil in the territorial waters of Svalbard under its own environmental legislation; see the Svalbard heavy fuel oil ban. Ships planning either trade need the national rules and permits, which are outside this article.
Enforcement and port State control
The Polar Code is enforced through the survey, certification and control machinery of SOLAS and MARPOL. SOLAS XIV/3 requires SOLAS ships to be surveyed and certificated under regulations I/7 to I/10, treats the Polar Ship Certificate as a certificate issued under regulation I/12 or I/13, and makes it subject to control under regulations I/19 and XI-1/4.
That gives a port State control officer three lines of inspection: the certificate itself (category, ice class, PST and limitations), the PWOM and the ship’s evidence of following it, and operational control under XI-1/4, which allows an officer, where there are clear grounds, to check that the crew is familiar with polar procedures. Officers’ polar certificates are checked under STCW regulation I/4. On the environmental side, the MARPOL Annex I, II, IV and V port State control provisions apply to the Part II-A rules through the chapters MEPC.265(68) added.
The flag Administration and its recognized organization carry the survey burden, and because validity is harmonized with SOLAS I/14 the Polar Ship Certificate is surveyed on the same dates as the ship’s other SOLAS certificates.
Amendments and pending work
MSC.538(107), adopted 8 June 2023 and in force 1 January 2026, is the first amendment to the Polar Code, which IMO calls “a first set of amendments”. It added chapters 9-1 and 11-1 for non-SOLAS ships, retitled chapters 9 and 11, and adjusted Part I-B sections 10 and 12 to match.
Three related items sit outside the Code:
- STCW. MSC.416(97) and MSC.417(97) amended the STCW Convention and Code, not the Polar Code, to create the polar certificates from 1 July 2018.
- Arctic fuel. At MEPC 83 (7 to 11 April 2025) the Committee noted ongoing work on “polar fuels”, fuels most suitable for Arctic use to reduce environmental impact, and extended the target completion year for that output to 2027. No black carbon regulation for Arctic shipping has been adopted; see black carbon and Arctic shipping.
- GHG measures. The IMO Net-Zero Framework was adjourned at the extraordinary MEPC session in October 2025 and has not been adopted, so it creates no polar obligation.
Common misreadings of the Polar Code
Several statements circulate in training material and older guidance that the Code text does not support.
- “The Code applies north of the Arctic Circle.” It applies inside the SOLAS XIV/1.3 boundary, which excludes the Norwegian mainland coast and Iceland and includes Hudson Bay north of 60°N.
- “Category B means IA Super or IA.” No Baltic class maps to a category without a flag-approved equivalency under Part I-B section 4.
- “Polar ships need two radars, one X-band and one S-band.” Chapter 9 has no radar requirement; SOLAS V/19.2.7 sets the second radar at 3,000 GT.
- “The Polar Code bans HFO in the Arctic.” The ban is MARPOL Annex I regulation 43A.
- “STCW polar training was mandatory from 2017.” It became mandatory on 1 July 2018.
- “The Arctic is a MARPOL special area.” It is not; the Arctic zero-discharge rules come from Part II-A.
Limitations
This article summarizes the Polar Code as adopted by MSC.385(94) and MEPC.264(68) and as amended by MSC.538(107) up to 15 October 2026. It does not reproduce the Code text, and the paragraph numbers given follow the IMO consolidated text; a flag Administration’s implementing rules, class rules and the PWOM for a specific ship govern actual compliance.
POLARIS values and outcomes depend on the RIV tables in MSC.1/Circ.1519 and on the ice data entered, so a RIO computed from this article’s description is not a substitute for the ship’s approved PWOM method. National overlays (Canada, Russia, Norway and others) change frequently and are described here only where their text is cited. IACS UR revisions apply by contract date, so the governing revision for a given hull must be confirmed against its contract and class documentation.
Frequently Asked Questions (FAQs)
When did the Polar Code enter into force?
The Polar Code took effect on 1 January 2017, the day SOLAS chapter XIV (added by MSC.386(94)) and the MARPOL amendments in MEPC.265(68) entered into force.
Both amending resolutions were deemed accepted on 1 July 2016 under the tacit acceptance procedure.
Which IMO resolutions adopted the Polar Code?
Two. MSC.385(94), adopted by the Maritime Safety Committee on 21 November 2014, adopted the safety-related Introduction and Parts I-A and I-B.
MEPC.264(68), adopted by the Marine Environment Protection Committee on 15 May 2015, adopted the environment-related Introduction and Parts II-A and II-B.
Is the whole Polar Code mandatory?
No. Parts I-A (safety) and II-A (pollution prevention) are mandatory.
Parts I-B and II-B are recommendatory guidance. Canada is the main exception in practice: SOR/2017-286 section 2(2) reads should as must in the documents it incorporates, so recommendatory Code wording it incorporates binds ships in Canadian Arctic waters.
Which ships must comply with Part I-A of the Polar Code?
Under SOLAS XIV/2.1.1, every ship certified in accordance with SOLAS chapter I that operates in polar waters, which in practice means passenger ships and cargo ships of 500 GT and upwards on international voyages.
Government ships in non-commercial service are outside the chapter, though they are encouraged to act consistently with it.
Does the Polar Code apply to fishing vessels and yachts?
Since 1 January 2026, yes, but only partly.
MSC.532(107) brought fishing vessels of 24 m in length overall and above, pleasure yachts of 300 GT and upwards not engaged in trade, and cargo ships of 300 GT and upwards but below 500 GT into SOLAS chapter XIV. These ships must comply with Polar Code chapters 9-1 (navigation) and 11-1 (voyage planning) only, on all voyages in the Antarctic area and on Arctic voyages beyond the territorial sea of their flag State.
By when must existing non-SOLAS ships comply with chapters 9-1 and 11-1?
SOLAS XIV/2.3, as amended by MSC.532(107), requires fishing vessels, pleasure yachts and small cargo ships constructed before 1 January 2026 to meet chapters 9-1 and 11-1 by 1 January 2027.
The regulation sets a calendar date, not a survey-linked date.
Do non-SOLAS ships need a Polar Ship Certificate?
No. The survey and certification requirement in SOLAS XIV/3 applies only to ships certified under SOLAS chapter I.
Fishing vessels, yachts and small cargo ships brought in from 1 January 2026 comply with chapters 9-1 and 11-1 under the new regulation XIV/3-1, which carries no certificate.
When did existing SOLAS ships have to comply with the Polar Code?
SOLAS XIV/2.2 required ships constructed before 1 January 2017 to meet the relevant requirements by the first intermediate or renewal survey, whichever occurred first, after 1 January 2018.
Where do Arctic waters begin under the Polar Code?
Arctic waters are defined by a boundary line in SOLAS XIV/1.3 and MARPOL, not by the Arctic Circle.
The line starts at 58°00’.0N 042°00’.0W, runs via the southern shore of Jan Mayen and Bjørnøya to Cap Kanin Nos, follows the northern Asian coast to the Bering Strait, runs along 60°N past Etolin Strait, and returns along 60°N to 056°37’.1W and then to the starting point. It excludes waters off Iceland and the Norwegian mainland south of that line.
Where is the Antarctic area?
SOLAS XIV/1.2 defines the Antarctic area as the sea area south of latitude 60°S.
The MARPOL Antarctic special area under Annexes I, II and V uses the same latitude.
What is the difference between Category A, B and C polar ships?
Polar Code Introduction paragraphs 2.1 to 2.3 define a Category A ship as designed for at least medium first-year ice (70 to 120 cm), a Category B ship as designed for at least thin first-year ice (30 to 70 cm), and a Category C ship as designed for open water or ice conditions less severe than Categories A and B.
The ice for Categories A and B may include old ice inclusions.
Which Polar Class does a Category A ship need?
Polar Code Part I-A paragraph 3.3.2 has Category A scantlings approved taking into account IACS Polar Class PC1 to PC5, and Category B scantlings PC6 or PC7, or other standards offering an equivalent level of safety.
The Code ties the categories to structural standards, not to a mandatory class notation.
Is a 1A Super ship Category A or Category B?
Not automatically. A Finnish-Swedish ice class reaches Category A or B only where the flag Administration approves an equivalency to an IACS Polar Class under Part I-B section 4, which is then noted on the Polar Ship Certificate.
Without that approval the ship is Category C.
Can a Category C ship enter ice?
Yes, within the limits set in its Polar Ship Certificate and Polar Water Operational Manual.
Category C covers ice conditions less severe than thin first-year ice, and an ice-strengthened Category C ship may operate in light ice where its operational limitations, typically assessed with POLARIS, allow it.
What is a Polar Ship Certificate and who issues it?
It is the certificate required by Polar Code Part I-A paragraph 1.3 for every SOLAS ship operating in polar waters.
The Administration or a recognized organization issues it after an initial or renewal survey, and it records the ship category, ice class, polar service temperature and operational limitations.
How long is a Polar Ship Certificate valid?
Part I-A paragraph 1.3.6 harmonizes its validity and survey dates with the other SOLAS certificates under regulation I/14, so it runs on the same cycle as the ship’s safety certificates.
Does a Category C cargo ship need a survey to get a Polar Ship Certificate?
Not always.
Part I-A paragraph 1.3.3 lets the Administration certify a Category C cargo ship on documented verification where the operational assessment shows no additional equipment or structural change is needed, with an onboard survey at the next scheduled survey.
What is the Polar Water Operational Manual?
The PWOM, required by Part I-A chapter 2, is the ship-specific manual that gives the owner, operator, master and crew the ship’s operational capabilities and limitations in polar waters, including the ice operational assessment method, the POLARIS speed limits where used, and any alternative design approved under SOLAS XIV/4.
What is the polar service temperature?
Part I-A paragraph 1.2.11 sets the polar service temperature (PST) at least 10°C below the lowest mean daily low temperature (MDLT) for the intended area and season.
It is specified for ships intended to operate in low air temperature, meaning a lowest MDLT below -10°C (paragraph 1.2.12), and systems must be fully functional at the PST.
How long must survival equipment last in polar waters?
For the maximum expected time of rescue, which Part I-A paragraph 1.2.7 states shall never be less than 5 days.
Personal and group survival equipment and survival-craft communications are sized to that period.
What is POLARIS?
POLARIS, the Polar Operational Limit Assessment Risk Indexing System, is the IMO methodology in MSC.1/Circ.1519 of 6 June 2016 for assessing a ship’s operational limitations in ice.
It computes a Risk Index Outcome (RIO) as the sum of each ice type’s concentration in tenths multiplied by its Risk Index Value for the ship’s ice class.
What does a negative RIO mean?
For a Polar Class ship, a RIO of 0 or above means normal operation, from -10 to below 0 means elevated operational risk with speed limits, and below -10 means operation subject to special consideration.
For a ship below PC7 or with no ice class, any negative RIO means special consideration (MSC.1/Circ.1519 Table 1.1).
What speed limits apply under POLARIS at elevated risk?
MSC.1/Circ.1519 Table 1.2 recommends 11 knots for PC1, 8 knots for PC2, 5 knots for PC3 to PC5 and 3 knots below PC5 when the RIO falls in the elevated-risk band.
These limits are written into the PWOM.
Does the Polar Code require two radars?
No. Polar Code chapter 9 contains no two-radar rule.
A second radar comes from SOLAS V/19.2.7 for ships of 3,000 GT and upwards regardless of trading area. Chapter 9 requires two independent echo-sounders or two transducers on ice-strengthened ships built from 2017, two non-magnetic heading means, a GNSS compass above 80 degrees latitude and two remotely rotatable searchlights.
What ice accretion allowance applies to polar stability?
Part I-A paragraph 4.3.1.1 requires the intact stability calculation to include icing of 30 kg/m2 on exposed weather decks and gangways and 7.5 kg/m2 on the projected lateral area above the waterline on each side.
What polar training do masters and officers need?
Polar Code Part I-A table 12.3.1 requires basic polar training for the master, chief mate and officers in charge of a navigational watch on tankers and passenger ships in open waters.
In other ice-covered waters it requires advanced training for the master and chief mate and basic training for navigational watch officers, on all ship types. In ice-free waters no polar training is required.
When did STCW polar training become mandatory?
On 1 July 2018, when MSC.416(97) (STCW regulation V/4) and MSC.417(97) (STCW Code section A-V/4) entered into force.
Seafarers who began polar service before 1 July 2018 had transitional routes to certification until 1 July 2020.
What sea service does the STCW advanced polar certificate require?
STCW regulation V/4.4 requires a basic polar certificate, at least two months of approved seagoing service in the deck department within polar waters (at management level or while performing watchkeeping duties at operational level) or equivalent approved service, and advanced training meeting section A-V/4 paragraph 2.
Can oily water be discharged in Arctic waters?
No. Polar Code Part II-A paragraph 1.1.1, made mandatory through MARPOL Annex I chapter 11, prohibits any discharge of oil or oily mixtures from any ship in Arctic waters.
Clean or segregated ballast is excepted. The Arctic is not a MARPOL Annex I special area; the zero-discharge rule comes from the Polar Code.
Does the Polar Code ban heavy fuel oil in the Arctic?
No. Part II-B only encourages applying MARPOL Annex I regulation 43 in Arctic waters.
The Arctic heavy fuel oil ban is MARPOL Annex I regulation 43A, added by MEPC.329(76), in force 1 November 2022 and applying from 1 July 2024, with waivers and an exemption to 1 July 2029 for ships with protected fuel tanks.
What fuel tank protection does the Polar Code require?
Part II-A paragraph 1.2.1 requires Category A and B ships constructed on or after 1 January 2017 with an aggregate oil fuel capacity of less than 600 m3 to keep all oil fuel tanks at least 0.76 m from the outer shell.
Tanks of 30 m3 or less are excepted. Larger ships fall under MARPOL Annex I regulation 12A.
Can food waste be discharged in Arctic waters?
Only under Part II-A paragraph 5.2.1: comminuted to pass a 25 mm screen, uncontaminated, as far as practicable from areas of ice concentration over 1/10, at least 12 nautical miles from the nearest land, ice shelf or fast ice, and never onto the ice.
Discharge of animal carcasses is prohibited.
Can noxious liquid substances be discharged in Arctic waters?
No. Part II-A paragraph 2.1.1, through MARPOL Annex II chapter 10, prohibits any discharge of NLS or mixtures containing them in Arctic waters.
Category A and B ships built from 2017 also need Administration approval to carry ship type 3 NLS in type 3 cargo tanks.
Can sewage be discharged in polar waters?
Only under Part II-A chapter 4, made mandatory by MARPOL Annex IV chapter 7, with distances measured from any ice shelf or fast ice as well as land.
Category A and B ships and passenger ships constructed on or after 1 January 2017 may discharge only treated sewage from an approved treatment plant.
Does Canada apply the Polar Code?
Yes.
Canada’s Arctic Shipping Safety and Pollution Prevention Regulations, SOR/2017-286, in force 19 December 2017, incorporate MSC.385(94) and MEPC.264(68), read the Code’s recommendations as mandatory, and add Zone/Date, AIRSS and POLARIS entry rules for Canadian shipping safety control zones.
Is Antarctic tourism insurance mandatory under the Antarctic Treaty?
Not yet.
Measure 4 (2004) on insurance and contingency planning for tourism and non-governmental activities has not become effective; the Antarctic Treaty Secretariat recorded 17 of 27 required approvals on 15 October 2026.
Has the Polar Code been amended since 2017?
Yes. MSC.538(107), adopted 8 June 2023 and in force 1 January 2026, added Part I-A chapters 9-1 and 11-1 for non-SOLAS ships and retitled chapters 9 and 11 to cover ships certified under SOLAS chapter I.
The STCW polar training package of 2016 amended the STCW Convention and Code, not the Polar Code itself.
Which IACS Polar Class rule revisions apply to a new ship?
IACS UR I1 Rev.2 (April 2016) for class descriptions; UR I2 Rev.4 (December 2019) for structure on ships contracted from 1 January 2021, replaced by Rev.5 (June 2025) for ships contracted from 1 January 2027; and UR I3 Rev.2 (January 2023, Corr.1 December 2024) for machinery on ships contracted from 1 July 2024.
Is the Polar Ship Certificate checked by port State control?
Yes.
SOLAS XIV/3 makes the Polar Ship Certificate subject to control under regulations I/19 and XI-1/4, and it is treated as a certificate issued under regulation I/12 or I/13, so a port State control officer can inspect it like any other SOLAS certificate.
Does a SOLAS ship need a Polar Ship Certificate for a short transit of Arctic waters?
Yes.
SOLAS XIV/2.1 applies to ships operating in polar waters with no minimum duration or distance, so a SOLAS ship that enters Arctic waters or the Antarctic area, even on a brief transit, must hold a valid Polar Ship Certificate and a PWOM.
Does Part II-A of the Polar Code apply to non-SOLAS ships?
Yes, where the relevant MARPOL annex applies to them.
Part II-A is made mandatory through MARPOL Annexes I, II, IV and V, so its reach follows each annex’s own application rules rather than SOLAS certification. A fishing vessel or yacht to which Annex I or Annex V applies is bound by the Arctic oil and garbage rules regardless of the 2026 SOLAS extension.
Must the Oil Record Book and SOPEP reflect polar operations?
Yes.
Polar Code Part II-A paragraph 1.1.4 requires operations in polar waters to be taken into account, as appropriate, in the Oil Record Book, the manuals and the shipboard oil pollution emergency plan or shipboard marine pollution emergency plan.
No question matches. Try a shorter or different word.
Sources
- IMO resolution MSC.385(94), International Code for Ships Operating in Polar Waters (Polar Code), adopted 21 November 2014 imo.org
- IMO resolution MSC.386(94), amendments to SOLAS 1974 adding chapter XIV, adopted 21 November 2014 imo.org
- IMO resolution MEPC.264(68), Polar Code environmental provisions, adopted 15 May 2015 imo.org
- IMO resolution MEPC.265(68), amendments to MARPOL Annexes I, II, IV and V, adopted 15 May 2015 imo.org
- IMO resolution MSC.532(107), 2023 amendments to SOLAS, revised regulations XIV/2 and XIV/3-1, adopted 8 June 2023 imo.org
- IMO resolution MSC.538(107), amendments to the Polar Code adding chapters 9-1 and 11-1, adopted 8 June 2023 imo.org
- IMO resolution MSC.416(97), amendments to the STCW Convention, regulation V/4, adopted 25 November 2016 imo.org
- IMO resolution MSC.417(97), amendments to the STCW Code, section A-V/4, adopted 25 November 2016 imo.org
- Canada, Arctic Shipping Safety and Pollution Prevention Regulations, SOR/2017-286 laws-lois.justice.gc.ca
- Antarctic Treaty Secretariat, Measure 4 (2004), insurance and contingency planning for tourism and non-governmental activities ats.aq
- IMO, International Code for Ships Operating in Polar Waters (Polar Code), consolidated text as adopted, MEPC 68/21/Add.1 Annex 10 imo.org
- IACS Unified Requirements I (Polar Class). UR I1 Polar Class descriptions and application, UR I2, UR I3 iacs.s3.af-south-1.amazonaws.com
- IACS UR I2 Rev.5 (June 2025), Structural requirements for Polar Class ships, as published by ClassNK classnk.or.jp
- Traficom (Finland), ice classes of ships. Ice Class Regulations TRAFICOM/68863/03.04.01.00/2021 and equivalence regulation TRAFICOM/281964/03.04.01.00/2023 traficom.fi
- IMO MSC.1/Circ.1641, Guidelines for safety measures for fishing vessels of 24 m in length and over operating in polar waters, 14 May 2021 register-iri.com
- Antarctic Treaty Secretariat, Measure 1 (2005), Annex VI to the Protocol on Environmental Protection, liability arising from environmental emergencies ats.aq
- IMO, Marine Environment Protection Committee 83rd session (7 to 11 April 2025), meeting summary imo.org