Righting Moment: Formula, Units and Heeling Moments

The righting moment is displacement times the righting arm GZ, in t·m or kN·m. How it differs from GZ, balances heeling moments and enters IMO stability rules.

Contents17 sections

The righting moment is the moment that turns a heeled ship back toward upright: RM = Δ × GZ, the displacement times the righting lever. With Δ in tonnes the result is in tonne-metres; multiplied by g it is in kilonewton-metres. The 2008 IS Code, adopted by resolution MSC.267(85), states its criteria in levers, but its heeling sources start as moments.

The righting moment links intact stability to every force that heels a ship. Wind, a turn, a crowd, shifted grain and a crane lift each apply a heeling moment. The ship comes to rest where the righting moment equals that moment. The GZ curve and righting arm article covers the lever curve and the Part A 2.2 criteria. This article covers the moment, its units and the rules that use it.

The righting couple: weight, buoyancy and the arm GZ

The righting moment is the moment of a couple. The ship’s weight acts down through the center of gravity G, and an equal buoyancy force acts up through the heeled center of buoyancy B₁. When the ship heels, the immersed wedge moves the center of buoyancy toward the low side. The two forces are then on parallel vertical lines.

The horizontal distance between the two lines is the righting lever GZ. Z is the foot of the perpendicular from G to the line of buoyancy. Figure 1 shows the couple on the example box hull of this article at 30 degrees of heel.

WLGB₁ZKweight Δgbuoyancy ΔgGZ = 1.05 mHeel 30°: GZ = 1.05 mRM = Δ × GZ = 13,000 t × 1.05 m = 13,657 t·m= 133,980 kN·m with g = 9.81 m/s²
Figure 1. Weight acts down through G and buoyancy acts up through B₁. The two forces form a couple, with arm GZ, that returns the ship toward upright. The values are those of the box. The hull is an example.

The example hull is a box section 100 m long, 20 m wide and 12 m deep. The hull floats in seawater at 13,000 t, with a draft of 6.34 m and KG 7.20 m. It is the same example hull as the cross curves of stability and KN tables article, so the numbers agree between the two pages. The hull’s GZ at 30 degrees is 1.05 m.

Definition; ITTC Symbols 2024, MS = Δ GZ

Righting moment

$$\textcolor{#2a78d6}{\mathit{RM}} = \textcolor{#eb6834}{\Delta}\,\textcolor{#1baf7a}{\mathit{GZ}} \quad (\mathrm{t\,m})$$
$$\textcolor{#2a78d6}{\mathit{RM}} = g\,\textcolor{#eb6834}{\Delta}\,\textcolor{#1baf7a}{\mathit{GZ}} \quad (\mathrm{kN\,m})$$

where

\(\mathit{RM}\)righting moment at heel angle θt·m, or kN·m
\(\Delta\)displacement, as a masst
\(\mathit{GZ}\)righting lever at the same heel anglem
\(g\)gravitational acceleration, 9.81m/s²

Units: tonne-metres, kilonewton-metres and newton-metres

IMO instruments state the righting and heeling moments in more than one unit, so read the unit from the instrument each time. The 2008 IS Code Part A 3.1.2 gives the turning moment in kN·m. SOLAS II-1/7-2.4, as replaced by MSC.421(98), gives its heeling moments in t·m. MSC.415(97) Part B 2.9 gives lifting moments in t·m. The 2009 MODU Code gives wind force in newtons.

A tonne-metre is a mass multiplied by a length. It is a moment only by convention, where g is understood. The 13,657 t·m of the example hull at 30 degrees is 133,980 kN·m with g = 9.81 m/s².

The SOLAS wind moment shows the conversion inside the formula. Mwind = P A Z / 9,806, with P in N/m², A in m² and Z in m. The numerator is in newton-metres, and the divisor 9,806 converts it to tonne-metres.

Displacement as a mass or a force

The International Towing Tank Conference defines the quantity differently. The ITTC Symbols and Terminology List, Version 2024, gives MS, the “Moment of ship stability in general”, as Δ GZ in N·m. In that list Δ is the “Displacement (buoyant) force” in newtons, and the ship mass is m, in kilograms.

In ITTC notation RM = Δ GZ is already a moment in N·m, because Δ is a force. In IMO notation Δ is in tonnes, so the same symbols give t·m. Both are correct, and an error by a factor of 9.81 follows from mixing them. The ITTC list also gives T, the “equivalent transverse heeling arm”, as heeling moment divided by Δ.

Righting moment and righting arm: why rules use the lever

The righting arm and the righting moment are one curve on two scales at one displacement. The righting moment is GZ times a displacement that does not change with heel. Figure 2 shows the example hull with GZ on the left scale and the righting moment on the right scale.

0°10°20°30°40°50°60°70°80°90°0.000.22,6000.45,2000.67,8000.810,4001.013,0001.215,6001.418,2001.620,800GZ (m)RM (t·m)Angle of heelΔ GM sin θlargest: GZ 1.35 m, RM 17,610 t·m at 39.4°30°: 1.05 m, 13,657 t·m71°
Figure 2. The GZ curve and the righting moment curve are one line on two scales, because displacement is constant. The dashed line is the small-angle form Δ GM sin θ, which leaves the curve above about 10 degrees.

The 2008 IS Code does not define the righting lever or the righting moment in its Introduction. Part A calls GZ the “righting lever”. The general criteria in Part A 2.2 are lever values and lever areas. The areas are 0.055 m·rad to 30 degrees, 0.09 m·rad to 40 degrees and 0.03 m·rad between them. GZ is at least 0.20 m at 30 degrees or more, and GM0 at least 0.15 m. A lever criterion applies to ships of every size without a size term.

Two ships with the same GZ

A large ship and a small ship with the same GZ do not have the same righting moment. For two geometrically similar ships at a scale ratio λ, GZ changes as λ, displacement as λ³, and the righting moment as λ⁴. This follows from the definition and holds for any consistent hull form.

The wind heeling moment changes as the lateral area times its lever, which is λ³. The wind heeling lever, moment divided by displacement, then does not change with size, while GZ grows as λ. A ship at half the size of a sister has half the GZ and the same wind heeling lever. Under the same wind pressure, the wind criterion is therefore harder for the small ship.

Same moment, different lever: added weight and lost buoyancy

The righting moment does not depend on how the displacement is counted, but GZ does. Damage stability shows this most clearly. The added weight method treats floodwater as cargo, and the lost buoyancy method treats the flooded space as no longer part of the hull.

Both methods give the same equilibrium and the same righting moment. The added weight method divides that moment by the intact displacement plus the floodwater. The lost buoyancy method divides it by the intact displacement alone. As an example, a righting moment of 5,200 t·m is a GZ of 0.400 m on 13,000 t and 0.371 m on 14,000 t.

The rule that a report uses determines which GZ applies. The MSC.429(98) Revised Explanatory Notes to SOLAS II-1 calculate the GZ curve with a constant intact displacement at all stages of flooding. For the final full phase of each stage, they allow the lost buoyancy method.

Moments in the loading condition: KG and free surface

The position of G, and so every righting moment, comes from a sum of moments in the loading condition. Each item in the loading table carries its mass and its height above the keel. Their products are vertical moments in t·m.

The sum of the vertical moments divided by the sum of the masses gives KG: KG = Σ(w × kg) / Δ. The free surface moments of the slack tanks, also in t·m, are summed separately. Divided by Δ, they give the free surface correction to KG.

A load of 200 t placed 10 m above the keel adds 2,000 t·m of vertical moment. Added to the example condition, 13,000 t at KG 7.20 m, it gives KG = (93,600 + 2,000) / 13,200 = 7.24 m. The center of gravity of a ship stub covers the longitudinal and transverse positions as well.

The height of G sets the lever even where the immersed shape is the same. Figure 3 shows two copies of the example hull rolling together to 28 degrees, with KG 7.20 m and 8.00 m. Buoyancy moves out the same way in both. GZ at 28 degrees is 0.925 m against 0.549 m, so the righting moment is 12,024 t·m against 7,142 t·m.

KG 7.20 mGM 1.23 mGZ 0.92 mGB′KG 8.00 mGM 0.43 mGZ 0.55 mGB′
Figure 3. Two copies of the example hull rolled to the same angle, with G at two heights. Buoyancy at B′ moves out the same way in both. The higher G puts the weight closer to the line of buoyancy, so GZ and the righting moment are smaller.Both ships roll together to the same angle, so only the height of G differs. Buoyancy at B′ moves out the same way in both. The green lever GZ is shorter on the right ship at every angle.

The lightweight moment is the starting row of every table. The inclining experiment fixes it, so an error in lightship KG carries into every righting moment the booklet reports.

Righting moment at small angles

At small angles of heel, the righting moment equals the displacement times the metacentric height GM times the sine of the heel. The line of buoyancy passes through the metacenter M while M stays fixed, so GZ = GM sin θ.

Small-angle relation

Righting moment at small heel

$$\textcolor{#2a78d6}{\mathit{RM}} \approx \Delta\,\textcolor{#eb6834}{\mathit{GM}}\,\sin\theta$$

where

\(\mathit{RM}\)righting momentt·m
\(\Delta\)displacementt
\(\mathit{GM}\)initial metacentric height, with free surface correctionm
\(\theta\)angle of heel, small°

The small-angle form is a good approximation only while M does not move. On the example hull, with GM 1.23 m, it gives 2,770 t·m at 10 degrees against an exact 2,955 t·m, 6% low. At 30 degrees it gives 7,976 t·m against 13,657 t·m, 42% low. The dashed line in Figure 2 shows the divergence.

The wall-sided formula extends the range while the immersed and emerged wedges stay within vertical sides. Beyond the deck-edge immersion angle only the KN cross curves give the exact value.

Negative GM and the angle of loll

With negative GM, the small-angle righting moment acts in the direction of the heel. The ship heels until the righting moment becomes positive again, at the angle of loll. The ship then lolls to either side and rests at that angle.

The loll is not a list. A list comes from a heeling moment, such as an off-center weight. A loll comes from a negative GM with no heeling moment. The correction is to lower G, which changes the sign of GM, not to move weight across the ship.

Stiff and tender ships: GM and the roll period

A large GM gives a large righting moment at small angles and a short, quick roll. A small GM gives a small righting moment and a long, slow roll. A ship with a large GM is called stiff, and one with a small GM tender; the tender and stiff ship stub covers the terms.

The 2008 IS Code Part A 2.3.4 estimates the roll period as T = 2 C B / √GM, with C = 0.373 + 0.023 (B/d) − 0.043 (LWL/100). For the example hull, C is 0.403, and T = 2 × 0.403 × 20 / √1.227 = 14.5 s. The natural period of roll stub covers the roll period itself.

The Code sets minimum values only. Part B 5.1.6 states that it is “advisable to avoid excessive values of metacentric height”, because a stiff ship rolls with high accelerations.

List from a transverse weight shift

A weight moved across the ship applies a heeling moment, its mass times the distance moved. The ship lists until the righting moment balances it. At small angles the balance is w d = Δ GM tan θ. The trim and list article covers combined trim and list.

Moment balance; inclining test, IS Code Annex 1

List from a transverse weight shift

$$\tan\textcolor{#2a78d6}{\theta} = \frac{\textcolor{#eb6834}{w\,d}}{\Delta\,\textcolor{#1baf7a}{\mathit{GM}}}$$

where

\(\theta\)angle of list at equilibrium°
\(w\,d\)heeling moment: mass moved times the transverse distance movedt·m
\(\Delta\)displacement, including the mass movedt
\(\mathit{GM}\)metacentric height, with free surface correctionm

As an example, 100 t moved 15 m across the example hull gives a heeling moment of 1,500 t·m. With Δ 13,000 t and GM 1.23 m, tan θ is 0.094 and the list is 5.4 degrees. The tangent form holds only while GM sin θ is a good model, so use the GZ curve for a list over about 10 degrees.

The longitudinal counterpart is the moment to change trim one centimetre, MCT1cm, read from the hydrostatic tables. The longitudinal metacentric height is far larger than GM, so the same moment changes trim by centimetres and list by degrees.

The heeling moment in the inclining test

The inclining experiment measures GM by applying known heeling moments and reading the heel. The 2008 IS Code Annex 1, paragraph 4.3.2, plots the tangent of the heel angle against the heeling moment W(x), weight times distance. The inverse of the slope gives Δ GM.

Part B 8.2.2.8 of the Code asks for test weights that give “a minimum inclination of one degree and a maximum of four degrees of heel to each side”. The Administration can accept a smaller angle on a large ship. In that range the small-angle balance holds, so the measured slope gives GM and, with KM from the hydrostatics, the lightship KG. ASTM F1321 covers the same test.

Heeling moments and the heeling lever

A heeling moment divided by the displacement is a heeling lever, and the heeling lever can be drawn on the GZ curve. Every heeling source in the 2008 IS Code starts as a moment, whether or not the Code prints the moment.

The table lists the moment sources in the instruments that this article covers.

Heeling sourceInstrumentMoment as writtenLever or limit
Steady windIS Code 2008, Part A 2.3.2P A Z, P = 504 Palw1 = P A Z / (1000 g Δ), constant with heel
Turning, passenger shipsIS Code 2008, Part A 3.1.2MR, kN·mHeel not over 10°
Passenger crowdingIS Code 2008, Part A 3.1.1No formula; assumptionsHeel not over 10°
Grain shiftGrain Code, A 7Volumetric heeling moment, m⁴λ0 = moment / (SF × Δ)
Anchor handlingMSC.415(97), Part B 2.7MAHHL = (MAH / Δ) cos φ
LiftingMSC.415(97), Part B 2.9HM = PL y cos φ, t·mHL = HM / Δ
Damage, passenger shipsSOLAS II-1/7-2.4Mpassenger, Mwind, Msurvivalcraft, t·ms_mom factor
Offshore units2009 MODU Code, 3.2F = 0.5 Cs CH ρ V² A, NArea ratio, 3.3.1

Wind: IS Code Part A 2.3

The wind heeling lever of the severe wind and rolling criterion is a moment divided by a weight. Part A 2.3.2 of the 2008 IS Code gives lw1 = P A Z / (1000 g Δ). P is 504 Pa, A is the lateral area above the waterline, and Z is its lever to the underwater lateral area.

IS Code 2008, Part A, 2.3.2

Wind heeling lever

$$\textcolor{#2a78d6}{l_{\mathrm{w1}}} = \frac{\textcolor{#eb6834}{P\,A\,Z}}{1000\,g\,\textcolor{#1baf7a}{\Delta}}$$

where

\(l_{\mathrm{w1}}\)steady wind heeling lever, constant at all anglesm
\(P\,A\,Z\)wind heeling moment: pressure 504 Pa times lateral area times leverN·m
\(\Delta\)displacementt
\(g\)gravitational acceleration, 9.81m/s²

The numerator P A Z is the wind heeling moment in newton-metres. The denominator 1000 g Δ is the ship’s weight in newtons, with Δ in tonnes. The gust lever lw2 is 1.5 lw1, and both levers are “constant values at all angles of inclination” under Part A 2.3.2.

As an example, take a lateral area of 1,500 m² with Z = 10 m on the example hull. P A Z is then 7,560 kN·m, or 771 t·m. The lever lw1 is 0.059 m, and the steady heel is about 2.8 degrees. The severe wind and rolling criterion of Part A 2.3 then compares areas on the GZ curve.

The 504 Pa has a source in wind speed. MSC.1/Circ.1281 section 3.5 states that a wind of 26 m/s in the Japanese heeling moment formula gives the IS Code pressure. Part A 2.3.3 sets the same 26 m/s, full scale, for model tests used as an alternative.

Turning: IS Code Part A 3.1.2

A turn heels a ship outward. By derivation, the lateral water force acts near half the draft while the inertia of the ship acts at G, which gives the lever KG − d/2 in the formula. Part A 3.1.2 of the 2008 IS Code gives the turning moment of a passenger ship as MR = 0.200 (V0²/LWL) Δ (KG − d/2), in kN·m.

IS Code 2008, Part A, 3.1.2

Heeling moment due to turning

$$\textcolor{#2a78d6}{M_{\mathrm{R}}} = 0.200\,\frac{\textcolor{#eb6834}{V_0}^{2}}{L_{\mathrm{WL}}}\,\Delta\left(\textcolor{#1baf7a}{\mathit{KG}} - \frac{d}{2}\right)$$

where

\(M_{\mathrm{R}}\)heeling moment in the turnkN·m
\(V_0\)service speedm/s
\(L_{\mathrm{WL}}\)length of the ship at the waterlinem
\(\Delta\)displacementt
\(\mathit{KG}\)height of the center of gravity above the baselinem
\(d\)mean draftm

Under Part A 3.1.2, “the angle of heel on account of turning shall not exceed 10°”. The passenger crowding and turning heel criteria article covers both passenger checks.

As an example, run the example hull at 15 knots (7.72 m/s), with LWL 100 m, KG 7.20 m and d 6.34 m. The turning moment MR is then 6,238 kN·m. Divided by g Δ, 127,530 kN, the lever is 0.049 m. The heel is about 2.3 degrees, inside the 10-degree limit.

Passenger crowding: IS Code Part A 3.1.1

The crowding moment is the sum of each passenger’s mass times the transverse distance from the centerline, with the passengers placed for the worst heel. The 2008 IS Code Part A 3.1.1 prints no formula for it. The Code sets the assumptions instead:

  • passenger mass at least 75 kg, with a higher value where the Administration sets one (3.1.1.1)
  • center of gravity 1 m above the deck for a standing passenger and 0.3 m above the seat for a seated one (3.1.1.2)
  • passengers placed for “the most unfavourable combination of passenger heeling moment and/or initial metacentric height”, where “a value higher than four persons per square metre is not necessary” (3.1.1.4)

Under Part A 3.1.1, the heel from crowding “shall not exceed 10°”. The rule applies to passenger ships under Part A 3.1, together with the general criteria of Part A 2.2 and 2.3.

Grain shift: the volumetric heeling moment

A grain cargo heels the ship when its surface shifts, and the International Grain Code states that shift as a volumetric heeling moment in m⁴. The Code divides it by the stowage factor and the displacement to give the heeling arm: λ0 = assumed volumetric heeling moment / (SF × Δ).

The Grain Code (MSC.23(59)) takes the heeling arm at 40 degrees as 0.8 λ0, with a straight line between. Part A 7.1.2 requires a residual area of at least 0.075 m·rad between the heeling arm and righting arm curves. The area runs to the angle of largest difference between the curves, 40 degrees or the angle of flooding, whichever is least. The IACS UR L5 onboard stability software requirement lists “allowable grain heeling moments” among the stability data a program holds.

Lifting: MSC.415(97) Part B 2.9

A crane lift over the side applies a heeling moment, the load times its transverse distance from the centerline. The moment falls with the cosine of heel. MSC.415(97), adopted 25 November 2016, added stability during lifting operations to Part B of the 2008 IS Code as 2.9.

Part B 2.9 applies to ships with keels laid on or after 1 January 2020, and to conversions after that date (2.9.1.1). Paragraph 2.9.1.2 sets a threshold value ML for the heeling moment. Paragraph 2.9.1.2 also brings in a lift that induces no transverse heeling moment but raises the vertical center of gravity by more than 1%, and the lifting of the ship’s own structures.

MSC.415(97), IS Code Part B 2.9.1.2 and 2.9.6.2

Lifting: threshold and heeling moment

$$\textcolor{#2a78d6}{M_{\mathrm{L}}} = 0.67\,\Delta\,\mathit{GM}\,\frac{f}{B}$$
$$\textcolor{#eb6834}{\mathit{HM}_{\varphi}} = P_{\mathrm{L}}\,y\cos\varphi, \qquad \textcolor{#1baf7a}{\mathit{HL}_{\varphi}} = \frac{\mathit{HM}_{\varphi}}{\Delta}$$

where

\(M_{\mathrm{L}}\)threshold value for the heeling momentt·m
\(\Delta\)displacement, including the lift loadt
\(\mathit{GM}\)initial metacentric height with free surface, including the lifting equipment and loadm
\(f\)minimum freeboard, weather deck to waterlinem
\(B\)moulded breadthm
\(\mathit{HM}_{\varphi}\)heeling moment of the lift at heel φt·m
\(P_{\mathrm{L}}\)mass of the lifted loadt
\(y\)transverse distance from the centerline to the loadm
\(\mathit{HL}_{\varphi}\)heeling lever of the liftm

The example hull, with GM 1.23 m, a freeboard of 5.66 m and a breadth of 20 m, gives ML = 3,024 t·m. That value is before the effect of the load on GM, which lowers ML. A lift of 100 t at 25 m from the centerline gives 2,500 t·m upright, below that threshold. GM in the threshold includes the free surface correction and the lifting equipment and load.

Paragraph 2.9.3.1 includes the lifting appliance and load in the displacement and center of gravity, “in which case no external heeling moment/heeling lever is applied”. For a lift within defined environmental and operational limits, paragraph 2.9.4.1.2.2 sets ARL ≥ 1.4 AHL. ARL is the area under the net righting lever curve, corrected for the crane heeling moment and the counter-ballast. AHL is the area under the wind heeling lever curve. Paragraph 2.9.6 gives the alternative that applies the lift as a heeling moment.

Figure 4 shows why counter-ballast needs that check. Two copies of the example hull make the same 100 t lift at 25 m, one with counter-ballast and one without. When the wire parts, the counter-ballasted ship is thrown 13.6 degrees to the far side. The ballast moment acts at once, and its static heel is 8.6 degrees.

No counter-ballastthe ship heels toward the loadheel 5.0° to the far sideCounter-ballastedballast in the far wing tankheel 13.6° to the far side
Figure 4. Two copies of the example hull just after the lift wire parts. The left ship swings back through upright from its heel toward the load. The right ship was held upright by counter-ballast, whose moment remains and throws it to the far side.The left ship heels toward the slewed load, and the right ship pumps counter-ballast to the far side to stay upright. When the wire parts, the left ship swings back and the right ship is thrown to the far side. Twice real time.

Paragraph 2.9.9.1 adds that “Ships should avoid resonant roll conditions when engaged in lifting operations”. The offshore cranes and heavy lifting article covers the crane side of the operation.

Anchor handling and towing

Anchor handling stability uses the heeling moment from the anchor handling wire tension. MSC.415(97) Part B 2.7 gives the heeling lever as HL = (MAH / Δ) cos φ, which falls with the cosine of heel.

Part B 2.7 sets a static heel limit and a residual area of 0.070 m·rad. The limit is the least of the angle at 50% of the largest GZ, the deck-edge immersion angle and 15 degrees. Part B 2.8 sets the towing and escort criteria for ships with keels laid on or after 1 January 2020. The girting and tug capsize article covers the towline case.

Free surface moment and liquid transfer

A slack tank produces a moment of its own, the free surface moment, in t·m. Part B 3.1 of the 2008 IS Code corrects GM and the GZ curve for it. The free surface effect article covers the methods of Part B 3.1.9.

The free surface moment divided by the displacement is the virtual rise of G used in the GM correction. Part B 3.1.12 leaves out a small tank whose free surface moment divided by the minimum displacement is less than 0.01 m at 30 degrees. The same moment is a larger rise of G on a light ship than on a loaded one.

Figure 5 shows the effect on two copies of the example hull in the same wind. One has a double-bottom tank pressed full and the other has the same tank half full. The half-full tank, 15 m long and 18 m wide, lowers GM from 1.23 m to 0.65 m, and the largest heel rises from 13.6 to 21.0 degrees.

Tank pressed fullliquid moves with the shipheel 13.2°Tank half fullsurface stays levelheel 21.0°
Figure 5. Two copies of the example hull in the same wind, at the largest heel of the cycle. The left tank is pressed full. The right tank is half full, and its liquid surface stays level and runs to the low side, which lowers GM.The same wind rocks both ships. The liquid in the half-full tank runs to the low side at each heel, and that ship heels further each way. Real time, with damping set so that the cycle repeats.

Equilibrium of moments: static and dynamic heel

A ship heeled by a moment comes to rest where the righting moment equals the heeling moment, if the moment is applied slowly. If it is applied suddenly, the ship rolls further, to the angle where the work of the two moments is equal. Figure 6 shows both angles for a heeling moment of 6,000 t·m on the example hull.

0°10°20°30°40°50°60°70°80°-4,00004,0008,00012,00016,00020,000Moment (t·m)Angle of heel →heeling momentrighting momentstatic 17.9°dynamic 32.0°
Figure 6. A heeling moment that is constant with heel acts on the example hull. Applied slowly, it heels the ship to the first intercept. Applied suddenly, the ship overswings to where the green area of excess righting moment equals the orange area of deficit.Move the heeling moment. The static heel is the first intercept. The dynamic heel is where the green area equals the orange area. When the green area runs out before the second intercept, a suddenly applied moment capsizes the ship although a static equilibrium exists.

Static heel at the first intercept

The static heel is the first intercept of the righting moment curve and the heeling moment curve. On the example hull, a constant 6,000 t·m gives a static heel of 17.9 degrees. The heeling lever is 6,000 / 13,000 = 0.462 m, and the same angle reads off the GZ curve at that lever.

A heeling moment larger than the largest righting moment has no static equilibrium. On the example hull that limit is about 17,610 t·m at about 39 degrees. MSC.415(97) Part B 2.9.6.4 takes the equilibrium heel of a lift as the first intersection of the two curves.

Dynamic heel and the energy balance

A moment applied suddenly accelerates the ship in heel before the righting moment can balance it. The ship stops at the angle where the work done by the righting moment equals the work done by the heeling moment.

Derivation; energy balance, MSC.1/Circ.1281 3.5.2.1

Work done by the righting moment

$$\textcolor{#2a78d6}{E} = \int_{0}^{\theta} \mathit{RM}\,d\theta = \textcolor{#eb6834}{\Delta} \int_{0}^{\theta} \textcolor{#1baf7a}{\mathit{GZ}}\,d\theta$$

where

\(E\)work to heel the ship from upright to θt·m·rad, or kJ with g
\(\Delta\)displacementt
\(\mathit{GZ}\)righting lever; its integral is the area under the GZ curvem
\(\theta\)angle of heelrad

On the curves, the work is an area. The orange area in Figure 6 is the excess of heeling moment over righting moment below the static angle. The green area is the excess of righting moment above it. The dynamic heel is where the two areas are equal: 32.0 degrees for 6,000 t·m.

Figure 7 shows the same 6,000 t·m applied slowly and at once to two copies of the example hull. The first ship settles near 17.9 degrees. The second swings to 32.0 degrees and rolls back to upright, because the scene has no damping.

Applied slowly6,000 t·m built up over 30 sheel over the cycle17.9°32.0°heel 18.4°Applied at once6,000 t·m from the first secondheel over the cycle17.9°32.0°heel 32.0°
Figure 7. The same wind heeling moment on two copies of the example hull. The left ship took it slowly and settles near the static heel. The right ship took it at once and is at its dynamic heel. The traces show heel over time.The left ship takes the moment over 30 s and stops at the first intercept, 17.9 degrees. The right ship takes it at once, swings on to 32.0 degrees and rolls back to upright, again and again, because the scene has no damping. Shown at 1.5 times real time.

MSC.1/Circ.1281, the Explanatory Notes to the 2008 IS Code, states in 3.5.2.1 that “The basic principle of the weather criteria is energy balance between the beam wind heeling and righting moments”. The dynamic stability article covers the area under the GZ curve as a lever quantity, in m·rad.

The second intercept and the reserve

The second intercept is the angle beyond the largest righting moment where the curve falls back to the heeling moment. Past it the heeling moment is larger again, and the ship capsizes. On the example hull, 6,000 t·m gives a second intercept at 63.5 degrees.

A suddenly applied moment needs green area before the second intercept. On the example hull the area runs out from about 10,200 t·m, although a static equilibrium exists up to about 17,610 t·m. The angle of vanishing stability and the downflooding angle limit the area that the criteria count.

Righting moment in damage stability: SOLAS II-1/7-2.4

SOLAS II-1/7-2.4 reduces the survival factor of a passenger ship when the residual righting moment after flooding is small against a heeling moment. The factor s_mom applies at final equilibrium. Regulation 7-2.4 states that it is “applicable only to passenger ships (for cargo ships s_mom,i shall be taken as unity)”.

SOLAS II-1/7-2.4, as replaced by MSC.421(98)

Heeling moment factor s_mom

$$\textcolor{#2a78d6}{s_{\mathrm{mom},i}} = \frac{(\textcolor{#eb6834}{\mathit{GZ}_{\max}} - 0.04)\,\Delta}{\textcolor{#1baf7a}{M_{\mathrm{heel}}}} \le 1$$

where

\(s_{\mathrm{mom},i}\)factor for heeling moments at final equilibrium, passenger ships
\(\mathit{GZ}_{\max}\)largest positive righting lever at final equilibriumm
\(\Delta\)intact displacement at the draft ds, dp or dlt
\(M_{\mathrm{heel}}\)largest of the passenger, wind and survival craft momentst·m

MSC.421(98), adopted 15 June 2017 and in force from 1 January 2020, replaced paragraphs 2 to 4.1.2 of Regulation 7-2. The Displacement is now “the intact displacement at the respective draught (ds, dp or dl)”. The SOLAS Chapter II-1 base text of MSC.216(82) used the subdivision draught.

Mheel is the largest of three moments, each in t·m:

  1. Mpassenger = (0.075 Np)(0.45 B), with Np the maximum number of passengers and B the breadth under Regulation 2.8. An alternative distributes 75 kg persons at four per square metre toward one side on the muster-station decks.
  2. Mwind = P A Z / 9,806, with P = 120 N/m², A the projected lateral area above the waterline and Z its lever to T/2.
  3. Msurvivalcraft, from all fully loaded davit-launched survival craft on the heeled side swung out. Persons outside the swung-out craft add no moment.

The 0.04 m in the formula is a lever subtracted from GZmax before it becomes a moment. As an example, 1,000 passengers on a 20 m breadth give Mpassenger = 675 t·m. With 13,000 t intact displacement, GZmax 0.10 m gives s_mom = 1.16, capped at 1. GZmax 0.07 m gives 0.58.

The factor multiplies into the final survival factor of probabilistic damage stability, so a small residual moment reduces the attained index A. For the safe return to port case, IACS UR L5 Rev.4 requires a Type 4 program to account for “applied moments such as wind, lifeboat launching, cargo shifts and passenger relocation”.

Righting moment curves for offshore units: the 2009 MODU Code

The 2009 MODU Code, IMO resolution A.1023(26) adopted 2 December 2009, states its stability criteria in moments, not levers. Paragraph 3.2.1 calls for curves of righting moments and wind heeling moments. The curves cover the full range of operating drafts, including transit, about the most critical axes.

A mobile offshore drilling unit has no single roll axis like a ship. For a semi-submersible drilling unit, the curves of paragraph 3.2.1 are therefore related to the most critical axes.

2009 MODU Code, A.1023(26), 3.2.3

Wind force on a MODU

$$\textcolor{#2a78d6}{F} = 0.5\,C_{\mathrm{s}}\,\textcolor{#eb6834}{C_{\mathrm{H}}}\,\rho\,\textcolor{#1baf7a}{V}^{2}\,A$$

where

\(F\)wind force on one exposed surfaceN
\(C_{\mathrm{s}}\)shape coefficient, Table 3-1
\(C_{\mathrm{H}}\)height coefficient, Table 3-2
\(\rho\)air mass density, 1.222kg/m³
\(V\)wind velocity: 36, 51.5 or 25.8m/s
\(A\)projected area of the surfacem²

The wind force on each surface follows paragraph 3.2.3, with the shape and height coefficients of Tables 3-1 and 3-2. Paragraph 3.2.4 sets the wind speeds:

  • 36 m/s (70 knots) for normal operating conditions
  • 51.5 m/s (100 knots) for the severe storm condition
  • not less than 25.8 m/s (50 knots) for sheltered locations

The heeling moment is the force times its lever, from the center of wind pressure to the center of lateral resistance. Paragraph 3.2.6 takes the lever with the unit floating free. Paragraph 3.2.7 allows a ship-shaped unit to take the wind heeling moment curve as varying with the cosine of heel.

The area ratio of paragraph 3.3.1

The MODU Code compares the area under the righting moment curve with the area under the wind heeling moment curve to the same angle. Figure 8 shows the comparison on the example hull with a heeling moment of 9,000 t·m that falls with the cosine of heel.

0°10°20°30°40°50°60°70°80°04,0008,00012,00016,00020,000Moment (t·m)Angle of heelfirst intercept 22.5°second intercept 66.7°ABCrighting momentwind heeling moment(A + B) / (B + C) = 11,352 / 8,261 = 1.37A under the righting moment curve onlyB under both curvesC under the wind heeling moment curve only
Figure 8. The 2009 MODU Code compares areas, not angles. Area A + B lies under the righting moment curve and area B + C under the wind heeling moment curve, both to the second intercept. The example heeling moment falls with the cosine of heel.

Paragraph 3.3.1 sets two values:

  • Surface and self-elevating units: the righting moment area to the second intercept or the downflooding angle, whichever is less, “not less than 40% in excess” of the wind heeling area.
  • Column-stabilized units: the same comparison to the downflooding angle, “not less than 30% in excess”.

The righting moment is also to be positive from upright to the second intercept. In Figure 8, A + B is 11,352 t·m·rad and B + C is 8,261 t·m·rad, a ratio of 1.37. A surface unit measured to the second intercept would fail the 40% excess at that ratio.

Paragraph 3.3.2 requires that a unit can reach the severe storm condition “in a period of time consistent with the meteorological conditions”.

MODU damage criteria

The damage criteria of the MODU Code also use moments. Paragraph 3.4.2 superimposes a 25.8 m/s (50 knots) wind from any direction on the damaged unit. For a column-stabilized unit, paragraph 3.4.3 limits the heel after damage to 17 degrees. Within a range of at least 7 degrees, the righting moment is to reach at least twice the wind heeling moment at the same angle.

For a self-elevating unit, paragraph 3.4.1.2 sets the range of stability after flooding of one compartment. The range is not less than 7° + 1.5 θs, and not less than 10 degrees.

Earlier text and the United States overlay

The 2008 IS Code Part B 2.6 originally carried the same MODU criteria, and MSC.319(89) later pointed it to the 2009 MODU Code. One table differs between the texts. The height coefficient table of the 2009 MODU Code has its top band at 259 m. The 2008 IS Code Part B 2.6 and 46 CFR Table 174.055(a) use 256 m.

The United States applies the same ratio in 46 CFR 174.045, as Area(A) ≥ K × Area(B). K is 1.4, or 1.3 for a column-stabilized unit. The offshore drilling and wells article covers MODU operations.

High-speed craft: moment criteria in the 2000 HSC Code

The 2000 HSC Code, adopted by resolution MSC.97(73) on 5 December 2000, writes several of its stability criteria directly as moments. Annex 6 covers hydrofoil craft, Annex 7 multihull craft and Annex 8 monohull craft.

  • Annex 6, 1.1.2: hydrofoil turning moment MR = 0.196 (V0²/L) Δ KG, in kN·m, for a turning radius of 2 to 4 craft lengths.
  • Annex 6, 1.1.3 and 1.1.4: the ratio K = Mc / Mv of the capsizing moment to the wind heeling moment is at least 1, with Mv = 0.001 Pv Av Z kN·m and Pv = 750 (Vw/26)² N/m².
  • Annex 7, 1.3: multihull wind lever HL1 = Pi A Z / (9,800 Δ), with Pi = 500 (Vw/26)² N/m², and HL2 = 1.5 HL1.
  • Annex 8, 2.1.3: monohull residual GZ after damage of at least the heeling moment divided by the displacement plus 0.04 m, and never less than 0.1 m.

The Annex 8 rule is the same construction as SOLAS s_mom: a moment, divided by the displacement, plus a fixed margin of 0.04 m. The High-Speed Craft Code article covers the Code.

Regional overlay: the United States weather criterion

The US Coast Guard writes its basic weather criterion as a moment balance solved for GM. 46 CFR 170.170(a) requires GM ≥ P A H / (W tan T) for each loading condition. This is a United States overlay on the IMO baseline, under 46 CFR Subchapter S.

46 CFR 170.170(a), United States

USCG weather criterion

$$\textcolor{#2a78d6}{\mathit{GM}} \ge \frac{\textcolor{#eb6834}{P\,A\,H}}{\textcolor{#1baf7a}{W}\tan T}$$

where

\(\mathit{GM}\)metacentric height requiredm
\(P\,A\,H\)wind heeling moment: pressure times lateral area times levert·m
\(W\)displacementt
\(T\)lesser of 14° or the heel that immerses half the freeboard to the deck edge°

P A H is the wind heeling moment. The ocean wind pressure is P = 0.055 + (L/1,309)² t/m², with lower values of P for partially protected and protected waters. W is the displacement in metric tons. T is the lesser of 14 degrees or the heel that immerses half the freeboard to the deck edge.

The formula is the small-angle balance of the inclining test, Δ GM tan θ = heeling moment. It is rearranged so that the required GM follows from the allowed heel. 46 CFR 170.170(d) generally limits the criterion to flush-deck, mechanically powered vessels of ordinary proportions and form. For those vessels, GZ at T, trimmed free, is at least the required GM times sin T. Other vessels need additional calculations.

Righting moments in the stability booklet and the loading computer

The stability booklet and the loading computer report levers, but they hold the moments from which the levers come. Part A 2.1.6 of the 2008 IS Code requires a stability booklet approved by the Administration for ships under Part A.

The loading table in the booklet sums the vertical moments and the free surface moments. The KN tables then give GZ, and the criteria test GZ. Part B 4.1.4.1 recommends that a stability instrument presents a table of righting lever against heel angle, including trim and draft, and the downflooding angle with its opening.

Heeling moments enter where the instrument handles them. IACS UR L5 Rev.4, section 5, lists “allowable grain heeling moments” among the stability data of a program.

Worked example: the righting moment curve of the example hull

The righting moment curve of a loaded condition follows from the GZ curve in one multiplication. The example hull is the box section of Figure 1: 100 m long, 20 m wide, 12 m deep, at 13,000 t with KG 7.20 m.

  1. Find the draft. T = 13,000 / (1.025 × 100 × 20) = 6.34 m.
  2. Find the hydrostatics. KB = 3.17 m, BM = B²/(12 T) = 5.26 m and KM = 8.43 m.
  3. Find GM. GM = KM − KG = 8.43 − 7.20 = 1.23 m.
  4. Read GZ at each angle from the cross curves: GZ = KN − KG sin θ.
  5. Multiply each GZ by 13,000 t to get the righting moment in t·m.
  6. Multiply by 9.81 to get kN·m where the instrument uses kN·m.
HeelGZ (m)RM (t·m)RM (kN·m)Δ GM sin θ (t·m)
10°0.2272,95528,9902,770
20°0.5397,00468,7105,456
30°1.05113,657133,9807,976
40°1.35317,595172,61010,254
50°1.12514,626143,48012,221
60°0.6568,53083,68013,816

The curve is largest at about 39 degrees, about 17,610 t·m, and returns to zero at 71.2 degrees. The area under the GZ curve is 0.220 m·rad to 30 degrees and 0.440 m·rad to 40 degrees. Multiplied by 13,000 t, these areas are 2,857 and 5,726 t·m·rad of work.

The lever values pass every general criterion of Part A 2.2 of the 2008 IS Code. The example shows the method only; it is a box, not a ship. The stability booklet and loading computer give the approved values for a real ship.

Common misconceptions about the righting moment

  • “GZ and the righting moment are the same thing.” They have the same curve shape at one displacement only. Between two ships, or two displacements, the righting moment differs by the ratio of the displacements.
  • “A tonne-metre is a unit of moment.” It is a mass times a length. Multiply by g for kN·m; the ITTC list writes the moment in N·m with Δ as a force.
  • “Δ GM sin θ is good to 30 degrees.” On the example hull it is 42% low at 30 degrees. The small-angle form is for small angles.
  • “The static heel is the largest heel.” A suddenly applied moment overswings the static angle, to 32.0 degrees against 17.9 degrees on the example hull for 6,000 t·m.
  • “Moving a weight inside the ship does not change the righting moment.” The displacement is the same, but a weight moved up raises G and reduces GZ. The righting moment then falls at every angle.
  • “The added weight and lost buoyancy methods disagree.” They give different GZ values from the same righting moment, because they divide by different displacements.

Limitations

The figures in this article come from an example box hull with exact geometry, not from a ship. A real hull has flare, sheer, a bilge radius and appendages, and its KN values come from its own approved cross curves. Use the approved stability booklet or an approved stability instrument for any operational decision.

The righting moment curve assumes a still-water GZ curve, with G fixed in the ship and free trim. MSC.1/Circ.1281 3.2.1.4 notes that the criteria use the still-water curve “notwithstanding the fact that if a ship sails in a seaway, the curve of static stability levers changes”. The second generation intact stability criteria address GZ in waves.

The dynamic heel of Figure 6 starts from upright with a constant heeling moment and no damping. The weather criterion of Part A 2.3 starts from a roll to windward and uses its own areas. A ship with bilge keels or marine stabilisers rolls less than the undamped energy balance predicts.

The HSC Code figures are from the text adopted by MSC.97(73). The MODU Code figures are from resolution A.1023(26); a unit certified to an earlier code follows that code. National rules, including 46 CFR, apply only to the vessels within their scope.

Frequently Asked Questions (FAQs)

What is the righting moment of a ship?

The righting moment is the moment of the couple formed by weight and buoyancy that turns a heeled ship back toward upright.

It equals the displacement multiplied by the righting lever GZ at the same angle of heel. With the displacement in tonnes, the result is in tonne-metres; multiplied by g, it is in kilonewton-metres.

Is the righting moment the same as the righting arm?

No: the righting arm GZ is a distance in metres, and the righting moment is that distance multiplied by the displacement.

The two curves have the same shape at one displacement, so a GZ curve is a righting moment curve on a different scale. They differ as soon as two ships, or two displacements of one ship, are compared.

What are the units of the righting moment?

IMO texts give moments in tonne-metres or kilonewton-metres, and the ITTC Symbols and Terminology List 2024 gives newton-metres.

The 2008 IS Code turning moment in Part A 3.1.2 is in kN·m. The SOLAS II-1/7-2.4 heeling moments and the MSC.415(97) lifting moments are in t·m. Check the unit of each instrument before you compare two moments.

How do I convert a righting moment from t·m to kN·m?

Multiply the value in tonne-metres by g, 9.81 m/s², to get kilonewton-metres.

A righting moment of 13,657 t·m is 133,980 kN·m. A tonne-metre is a mass times a length, so it becomes a true moment only when it is multiplied by g.

What symbol does the ITTC use for the righting moment?

The ITTC Symbols and Terminology List, Version 2024, uses MS, the moment of ship stability in general, defined as Δ GZ in newton-metres.

In the ITTC list Δ is the displacement force in newtons, and the ship mass is m. Heeling moments carry MS with a subscript, or their own symbols such as MR for turning and MW for wind.

Why do the IS Code criteria use GZ and not the righting moment?

The criteria in Part A 2.2 of the 2008 IS Code are written as lever values and lever areas so that one set of numbers applies to ships of every size.

A 0.20 m GZ at 30 degrees means the same thing for a coaster and a VLCC, while a righting moment of 10,000 t·m does not. Heeling moments are divided by the displacement to give heeling levers for the same reason.

Does a larger ship with the same GZ have more stability?

A larger ship with the same GZ has a larger righting moment, in proportion to its displacement.

Under a heeling moment that is also in proportion to its displacement, it heels the same amount. For geometrically similar ships the case is different. GZ scales with length and displacement with length cubed, so the righting moment scales with length to the fourth power. The wind heeling moment scales with length cubed, so the wind heeling lever stays the same while GZ grows.

What is the righting moment at zero heel?

The righting moment is zero when the ship is upright, because G and B are on one vertical line and there is no arm.

It grows with heel at a rate set by the metacentric height. At small angles the righting moment is about Δ GM sin θ.

At what angle is the righting moment largest?

The righting moment is largest at the angle of the largest GZ, because the displacement does not change with heel.

On the example box hull of this article, at 13,000 t with KG 7.20 m, the largest value is about 17,610 t·m. It occurs at about 39 degrees. The 2008 IS Code Part A 2.2.3 requires the largest GZ at an angle not less than 25 degrees.

Up to what angle is the formula RM = Δ GM sin θ valid?

The small-angle formula is valid only while the metacenter stays fixed, which means small angles of heel.

On the example hull the formula is 6% low at 10 degrees and 42% low at 30 degrees. For larger angles use the GZ curve from the cross curves of stability.

What happens to the righting moment when GM is negative?

With negative GM the righting moment at small angles acts to increase the heel, so the ship heels until the righting moment becomes positive again, at the angle of loll.

If GZ never becomes positive, the ship capsizes. The heel at loll is not a sign of a list from an off-center weight and is corrected in a different way.

What is a heeling moment?

A heeling moment is any moment that turns the ship away from upright, for example from wind on the lateral area, a turn, a crowd of passengers on one side, a shift of grain or a crane lift.

In equilibrium the righting moment equals the heeling moment. Divided by the displacement, a heeling moment becomes a heeling lever that can be drawn on the GZ curve.

How is a heeling moment turned into a heeling lever?

Divide the heeling moment by the displacement, in the same mass or force units.

The 2008 IS Code Part A 2.3.2 does this for wind: lw1 = P A Z / (1000 g Δ). P A Z is the wind heeling moment in newton-metres, and 1000 g Δ is the weight in newtons. MSC.415(97) Part B 2.9.6.2 does the same for a lift: HL = HM / Δ.

What is the heeling moment due to turning in the IS Code?

The 2008 IS Code Part A 3.1.2 gives the turning moment of a passenger ship as MR = 0.200 (V0² / LWL) Δ (KG − d/2), in kN·m.

V0 is the service speed in m/s, LWL the waterline length and Δ the displacement in tonnes. KG is the height of G above the baseline, and d the mean draft. The heel from this moment shall not exceed 10 degrees.

How is the passenger crowding moment calculated?

The 2008 IS Code Part A 3.1.1 prints no formula for the crowding moment; it sets the assumptions from which the moment is calculated.

Each passenger is at least 75 kg. The center of gravity is 1 m above the deck for a standing passenger and 0.3 m above the seat for a seated one. No more than four persons per square metre is needed, and the heel from crowding shall not exceed 10 degrees.

What is s_mom in SOLAS damage stability?

s_mom is the factor in SOLAS II-1/7-2.4 that accounts for heeling moments at final equilibrium after flooding. s_mom equals (GZmax − 0.04) × Displacement / Mheel, and is not more than 1.

The factor applies only to passenger ships; for cargo ships it is taken as unity.

Which heeling moments enter the SOLAS s_mom factor?

Mheel is the largest of three moments in SOLAS II-1/7-2.4, as replaced by MSC.421(98): the passenger, wind and survival craft moments.

The passenger moment is (0.075 Np)(0.45 B) in t·m. The wind moment is P A Z / 9,806 in t·m, with P = 120 N/m². The survival craft moment comes from all fully loaded davit-launched craft swung out on the heeled side.

How does the MODU Code use righting moment curves?

The 2009 MODU Code, resolution A.1023(26), compares the area under the righting moment curve with the area under the wind heeling moment curve.

For surface and self-elevating units, the righting moment area is to be not less than 40% in excess of the wind heeling area. That area runs to the second intercept or the downflooding angle, whichever is less. For column-stabilized units the excess is 30%, measured to the downflooding angle.

Which wind speeds does the MODU Code use?

The 2009 MODU Code paragraph 3.2.4 uses 36 m/s (70 knots) for normal operating conditions and 51.5 m/s (100 knots) for the severe storm condition.

A minimum of 25.8 m/s (50 knots) applies to sheltered locations and to the damage condition in 3.4.2. The wind force is F = 0.5 Cs CH ρ V² A with an air density of 1.222 kg/m³.

What is the damage criterion for a column-stabilized MODU?

After damage, the 2009 MODU Code 3.4.3 limits the heel of a column-stabilized unit to 17 degrees.

Within a range of at least 7 degrees, its righting moment is to reach at least twice the wind heeling moment, both at the same angle. The wind is 25.8 m/s (50 knots) from any direction.

When does a crane lift need the MSC.415(97) lifting criteria?

MSC.415(97) Part B 2.9 applies to lifts whose heeling moment exceeds the threshold ML = 0.67 Δ GM f/B, in t·m.

The ships are those with keels laid on or after 1 January 2020, and conversions after that date. Part B 2.9 also covers a lift that raises the vertical center of gravity by more than 1% without a heeling moment, and the lifting of the ship’s own structures.

What is the static heel under a heeling moment?

The static heel is the angle at which the righting moment first equals the heeling moment, the first intercept of the two curves.

A ship to which the moment is applied slowly comes to rest there. On the example hull, 6,000 t·m gives a static heel of 17.9 degrees.

Why does a suddenly applied heeling moment heel the ship further?

A heeling moment applied suddenly does work on the ship before the righting moment builds up, so the ship rolls past the static angle.

It stops where the work of the righting moment equals the work of the heeling moment, which on the curves is where two areas are equal. On the example hull, 6,000 t·m applied suddenly heels the ship to 32.0 degrees, against 17.9 degrees static.

Is dynamic stability the same as the righting moment?

No: dynamic stability is the work done to heel the ship, which is the area under the righting moment curve, or the displacement times the area under the GZ curve.

The righting moment is the ordinate; dynamic stability is the integral. MSC.1/Circ.1281 3.5.2.1 describes the weather criterion as an energy balance between the heeling and righting moments.

What moment is measured in an inclining test?

The inclining test applies a known heeling moment, the test weight times the distance it is shifted, and measures the heel it causes.

The 2008 IS Code Annex 1 plots the tangent of the heel angle against this moment, and the inverse of the slope gives Δ GM. Part B 8.2.2.8 asks for test weights that give between one and four degrees of heel to each side.

How does the US Coast Guard weather criterion use the heeling moment?

46 CFR 170.170 requires GM ≥ P A H / (W tan T): the wind heeling moment P A H divided by the displacement W and the tangent of an allowed heel T.

T is the lesser of 14 degrees or the heel that immerses half the freeboard to the deck edge. The rule is a United States overlay and applies to vessels under the USCG stability regulations.

What does the HSC Code require for residual GZ after damage?

For monohull craft, the 2000 HSC Code Annex 8 paragraph 2.1.3 requires a residual GZ of at least the heeling moment divided by the displacement plus 0.04 m, and never less than 0.1 m.

The heeling moment is the greatest of passenger crowding, survival craft launching and wind. The rule turns a moment into a lever by dividing by the displacement.

Do the added weight and lost buoyancy methods give the same righting moment?

Yes: both methods of damage calculation give the same equilibrium and the same righting moment, but they report different GZ and GM values.

The added weight method divides the righting moment by the intact displacement plus the floodwater, and the lost buoyancy method by the intact displacement only. The righting moment is the quantity that does not depend on the method.

Does the loading computer calculate applied heeling moments?

IACS UR L5 Rev.4 requires a Type 4 safe return to port program to account for applied moments such as wind, lifeboat launching, cargo shifts and passenger relocation.

Grain heeling moments are part of the stability data an onboard program holds.

Does the moment to change trim relate to the righting moment?

The moment to change trim one centimetre, MCT1cm, is the longitudinal counterpart of the righting moment at small angles.

MCT1cm is Δ GML divided by 100 times the ship length, with GML the longitudinal metacentric height. GML is far larger than GM, so a trimming moment changes trim by centimetres where the same transverse moment lists the ship by degrees.

Sources

  1. IMO Resolution MSC.267(85). International Code on Intact Stability, 2008 imo.org
  2. IMO MSC.1/Circ.1281. Explanatory Notes to the International Code on Intact Stability, 2008 denizcilik.uab.gov.tr
  3. IMO Resolution MSC.415(97). Amendments to Part B of the International Code on Intact Stability, 2008 imo.org
  4. IMO Resolution MSC.421(98). Amendments to SOLAS Chapter II-1, subdivision and damage stability imo.org
  5. IMO Resolution MSC.216(82). Amendments to SOLAS 1974, revised Chapter II-1 Parts A, B and B-1 imo.org
  6. IMO Resolution A.1023(26). Code for the Construction and Equipment of Mobile Offshore Drilling Units, 2009 imo.org
  7. IMO Resolution MSC.97(73). International Code of Safety for High-Speed Craft, 2000 imo.org
  8. IMO Resolution MSC.23(59). International Code for the Safe Carriage of Grain in Bulk imo.org
  9. IMO Resolution MSC.429(98). Revised Explanatory Notes to the SOLAS chapter II-1 subdivision and damage stability regulations imo.org
  10. IACS UR L5 Rev.4 (June 2020). Computer Software for Onboard Stability Calculations iacs.s3.af-south-1.amazonaws.com
  11. ITTC Symbols and Terminology List, Version 2024. alphabetic list ittc.info
  12. US 46 CFR 170.170. Weather criteria govinfo.gov