Rudders and Ship Steering: Types, Forces, Standards

How ship rudders work: hydrodynamics, spade and horn types, IACS UR S10 loads, stock and bearings, IMO maneuvering criteria and energy-saving rudder designs.

Contents16 sections

A rudder is the hinged control surface at a ship’s stern that turns rudder angle into a transverse force, and that force into the yaw moment that changes heading. On steel ships of 24 m and over its structure is sized under IACS Unified Requirement S10: the rudder force, the torque, the stock, the pintles, the bearings and the couplings. Its effect on the ship as a whole is judged against IMO resolution MSC.137(76) of 4 December 2002, the Standards for Ship Manoeuvrability, a recommendation that sets turning, yaw-checking and stopping limits for ships of 100 m and over and for chemical tankers and gas carriers of any length.

The rudder is one half of the steering system. The other half, the marine steering gear that turns the stock on a helm order, is governed by SOLAS Regulations II-1/29 and II-1/30 and by IACS UR M42, and has its own article. This article covers the rudder and the ship-level standards. That means hydrodynamics, rudder types, UR S10 loads and scantlings, bearings and survey, the IMO maneuvering criteria and the information carried on board, steering by azimuth thrusters and pods, and rudder casualties with an official report.

Rudder and steering gear: where the boundary lies

The boundary is the rudder stock. Everything from the stock’s coupling to the rudder blade, together with the stock itself, the bearings that carry it and the trunk it passes through, is rudder structure under IACS UR S10. The tiller or rotary vane keyed to the stock head, the hydraulic power units, the control system and the alarms are steering gear under SOLAS Chapter II-1 Regulation 29 and IACS UR M42.

The two meet at the rudder torque. UR S10 gives the torque the stock is sized for, and the steering gear has to deliver it. The stock diameter that comes out of that torque also decides which steering gear rules apply. SOLAS II-1/29.3.3 requires the main gear to be power-operated in any case where the stock exceeds 120 mm in way of the tiller, and 29.4.3 sets the same rule for the auxiliary gear at 230 mm, excluding strengthening for navigation in ice in both cases.

The SOLAS performance test belongs to the gear, not the rudder. Regulation II-1/29.3.2 requires the main steering gear to put the rudder from 35 degrees on one side to 35 degrees on the other at the deepest seagoing draught and maximum ahead service speed. It must also go from 35 degrees on either side to 30 degrees on the other in not more than 28 seconds. That is a mean rate of at least 65/28, about 2.32 degrees per second.

Formula

Rudder Rate Check

$$\dot\theta = \frac{65^\circ}{t_{35 \to 30}}$$

where

\(t_{35 \to 30}\)Measured time, 35 degrees on either side to 30 degrees on the other (limit 28 s)s
\(\dot\theta\)Mean rudder rate (minimum 65/28, about 2.32 degrees per second)deg/s

Source: SOLAS II-1 Reg 29.3.2 (main steering gear, deepest seagoing draught, maximum ahead service speed)

Those rules took their current shape in the 1981 SOLAS amendments of MSC.1(XLV), in force 1 September 1984, which followed the steering failure of the Amoco Cadiz in 1978. Power unit duplication, the 45-second single-failure rule for tankers, hydraulic locking alarms and the pre-departure and three-monthly drills under SOLAS V/26 are all steering gear matters, set out in the steering gear article.

Rudder hydrodynamics

A rudder steers because it is a lifting foil set at an angle to the water flowing past it. Deflect the blade, and the pressure on one face rises while the pressure on the other falls; the resultant acts on the blade and, through the blade’s distance from the ship’s center of gravity, turns the hull.

Lift, drag and the normal force

Engineers resolve the rudder’s hydrodynamic force in two ways. Lift is the component perpendicular to the incoming flow and drag the component parallel to it. The normal force is the component perpendicular to the rudder chord, and it is the one that loads the stock, the bearings and the steering gear. At zero angle a symmetric section carries no lift; as the angle grows the normal force grows with it, and so does the drag the rudder adds to the ship’s resistance.

At a given rudder angle the hydrodynamic force scales with the square of the inflow speed. UR S10 carries that through to its design load, where the rudder force is proportional to \(V^2\). Halve the speed and the force available to steer falls to a quarter. That relation is why a ship at slow speed in a harbor steers poorly unless the propeller is turning, and why bow and stern thrusters and tugs take over at the berth.

Stall and the 35-degree convention

A foil’s lift rises with angle until the flow on the suction face separates, and then falls away. That is the stall. Its angle depends on the section, the aspect ratio and the inflow, and a rudder working in a propeller slipstream behaves differently from one outside it. No IMO or IACS instrument fixes a stall angle.

The 35-degree figure that runs through steering practice is the angle at which SOLAS II-1/29.3.2 tests the main steering gear. No IMO or IACS instrument fixes a maximum rudder angle, and 35 degrees is not a hydrodynamic limit. MSC.137(76) 4.2.2 runs the turning test at 35 degrees of rudder “or the maximum rudder angle permissible at the test speed”, and high-lift rudders are designed for larger working angles, which the section on rudder types below describes.

Balance and the center of pressure

The resultant force on a rudder acts at its center of pressure. For scantlings UR S10 places it at 0.33 of the rudder breadth from the leading edge going ahead and at 0.66 going astern, when the trailing edge leads. The torque on the stock is the force times the distance from the stock axis to that center. Placing part of the blade area forward of the stock, which is called balance, shortens the lever and cuts the torque the steering gear has to deliver.

UR S10 does not set a limit on balance. It builds balance into the torque calculation instead, through the ratio \(k_1\) of the area forward of the stock to the total rudder area, and sets a floor on the ahead lever of 0.1 times the mean breadth of the rudder (S10.2.1.2). The more balance, the shorter the ahead lever and the more the astern case decides the stock size, as the worked example below shows.

Rudder types

Rudders are classed two ways: by how the blade is supported, which drives the structure, and by the section profile, which drives the force. UR S10 recognizes both. Its annexes give separate support models for each arrangement, and its Table 1 gives a profile factor \(K_2\) for each family of sections.

Support arrangementHow the blade is carriedUR S10 treatment
Spade rudderFrom the stock only, cantilevered below the hullAnnex S10.2; with the trunk extending inside the blade, Annex S10.3 and two load cases
Rudder with a sole pieceStock above, heel pintle in a sole piece extending aft from the keelAnnex S10.4; sole piece as an elastic support
Semi-spade rudderStock above, pintle in a fixed rudder horn part-way downAnnexes S10.5 and S10.6; horn as an elastic support, horn strength in section 9

Spade rudders

A spade rudder hangs from its stock with nothing below the hull. All the bending from the rudder force passes into the stock and is reacted by the neck bearing and the upper bearing, so the stock of a spade rudder is sized for combined bending and torsion, not torsion alone. Where the rudder trunk extends down inside the blade, UR S10 Annex S10.3 checks two load cases: pressure on the entire rudder area, and pressure only on the part below the middle of the neck bearing.

The arrangement has no horn and no sole piece in the water ahead of or above the blade. Its price is a heavier stock and heavier bearings for the same rudder area, because no lower support shares the bending.

Semi-spade rudders on a rudder horn

A semi-spade rudder turns about one axis, the stock axis, along its full height. Part-way down, a pintle on that axis sits in a bearing in the rudder horn, a fixed structure extending down from the hull. The horn acts as an elastic support: it takes part of the bending load off the stock, and in exchange it is loaded in bending, shear and torsion itself. UR S10 section 9 sets the horn’s strength check, and Rev.8 clarified how the horn’s section areas are taken in it.

The blade below the horn pintle has no further support. At the horn the blade has a recess to clear the horn, and UR S10 S10.5.1 sets the allowable stresses in way of that recess at 75 N/mm2 in bending, 50 N/mm2 in shear and 100 N/mm2 equivalent, regardless of the steel’s k, against 110/k, 50/k and 120/k N/mm2 elsewhere in the blade. The recess radii are to be at least five times the plate thickness and not less than 100 mm (S10.1.4.2).

Flap rudders

A flap rudder carries a hinged flap at its trailing edge, linked so that the flap deflects further than the main blade. The combined section has more camber than a plain rudder at the same angle and so more lift. Becker Marine Systems states that its flap rudder gives a “10-20% increase in manoeuvring forces”, that a 45-degree rudder angle produces a 90-degree flap angle, and that flap angles reach 100 degrees. Becker’s King Support variant, the FKSR, is one of several support arrangements for the flap rudder, which the maker describes as used mainly on larger ships with a rudder surface of over 20 m2. FKSR is not the name of the flap rudder itself.

UR S10 1.1.1 extends to “some enhanced profile rudders with special arrangements for increasing the rudder force” without naming flap rudders, so the classification society decides whether a given flap rudder falls within it and which profile factor applies. Table 1 lists high lift rudders at 1.70 ahead and 1.30 astern. The flap’s hinge and linkage add wearing parts that a one-piece rudder does not have.

Schilling and other high-lift rudders

The Schilling rudder is a one-piece high-lift rudder with a fishtail trailing edge and no moving parts. Becker Marine Systems states that it operates at rudder angles of up to 70 degrees to either side, against 35 degrees for a conventional semi-spade rudder, and gives small turning circles “even at zero speed with angles of 65°-70°”. UR S10 Table 1 lists a fish tail profile at a \(K_2\) of 1.40 ahead and 0.80 astern; which row a particular rudder takes is the classification society’s decision.

A rudder that works at 70 degrees needs steering gear designed for that travel. The SOLAS test still runs 35 to 30 degrees; a larger working angle is a design choice that the steering gear, the stops and the angle indication have to match.

Twisted rudders and rudder bulbs

The flow leaving a propeller rotates, so the water reaching the upper half of a rudder behind it arrives at a different angle from the water reaching the lower half. A twisted rudder shapes its leading edge to meet that rotation, twisting one way above the propeller shaft line and the other way below it, which reduces the local angle of attack on the leading edge. A rudder bulb, a streamlined body on the rudder in line with the propeller hub, sits in the hub vortex.

Becker describes its Twist Rudder as giving “significant power savings” and “reduced cavitation and rotational losses”, and offers a rudder bulb as an option, but publishes no percentage. The saving from any of these devices depends on the propeller loading, the wake and the operating speed, and is established for a particular ship by model test or a sea-trial comparison, not by a catalog figure. A fuel saving lowers the attained Carbon Intensity Indicator in proportion to the fuel saved; it does not change the required value.

The Becker Twisted Fin is not a rudder. Becker describes it as a pre-swirl device fitted in front of the propeller, with a power saving of “up to 4%” stated by the maker, and it can be combined with the Twist Rudder. Pre-swirl fins, ducts and boss-cap fins sit with the other energy-saving devices.

Rudder force and torque under IACS UR S10

IACS UR S10 gives the design rudder force, the torque and the scantlings that follow from them for steel rudders on ships of 24 m and over. Its scope is “ordinary profile rudders, and … some enhanced profile rudders with special arrangements for increasing the rudder force” (1.1.1). The formula is a rule load for scantlings. It is not a prediction of the force the rudder develops in a turn, and the classification society may accept a direct analysis as equivalent under clause 1.5.

Which revision applies

UR S10 revisions apply by the date of the contract for construction, as defined in IACS Procedural Requirement 29. Rev.7, issued in February 2023 with Corrigendum 1 in June 2023 and Corrigendum 2 in May 2024, applies to ships contracted on or after 1 July 2024. Rev.8, dated 4 September 2025, applies to ships contracted on or after 1 January 2027.

Rev.8 changed two things. Clause 1.2.3 now places the trunk seal relative to the waterline at scantling draught without trim. Clause 9.2.1 and Annex S10.5 now describe how the rudder horn’s section areas are taken. The force, torque, stock, bearing, clearance and coupling clauses are unchanged, so the figures below apply to both revisions.

Rudder force

Formula

Rudder Force and Torque

$$C_R = 132 \, K_1 K_2 K_3 \, A \, V^2, \quad Q_R = C_R \, r, \quad r = c \, (\alpha - k_1)$$

where

\(C_R\)Rudder forceN
\(A\)Rudder blade aream2
\(V\)Maximum service speed on the summer load waterline; below 10 kn use (V + 20)/3; astern, maximum astern speed, not less than 0.5Vkn
\(K_1\)Aspect ratio factor, (lambda + 2)/3, lambda = b^2/A_t not more than 2
\(K_2\)Profile factor, UR S10 Table 1 (NACA-00 1.10 ahead, 0.80 astern)
\(K_3\)Location factor: 0.8 outside propeller jet, 1.15 behind fixed nozzle, 1.0 otherwise
\(Q_R\)Rudder torqueN m
\(c\)Mean breadth of rudder aream
\(\alpha\)0.33 ahead, 0.66 astern
\(k_1\)A_f/A, area forward of the stock centerline over rudder area; r not less than 0.1c ahead

Source: IACS UR S10 Rev.8 (September 2025), S10.2.1.1 and S10.2.1.2 (unchanged from Rev.7)

Clause S10.2.1.1 gives the rudder force as \( C_R = 132\,K_1 K_2 K_3\,A\,V^2 \) newtons. \(A\) is the rudder blade area in m2. \(V\) is the maximum service speed in knots with the ship on the summer load waterline; below 10 knots the rule uses \( (V + 20)/3 \), and for the astern case it uses the maximum astern speed as defined in SOLAS Regulation II-1/3.15, not less than 0.5 V. The three factors carry the geometry:

  • \( K_1 = (\lambda + 2)/3 \), the aspect ratio factor, with \( \lambda = b^2/A_t \) not taken greater than 2. \(b\) is the mean height of the rudder area and \(A_t\) is the blade area plus the area of any rudder post or horn within the height \(b\).
  • \(K_2\), the profile factor, from Table 1 below, with separate values ahead and astern.
  • \(K_3\), the location factor: 0.8 for rudders outside the propeller jet, 1.15 for rudders behind a fixed propeller nozzle such as a Kort nozzle, and 1.0 otherwise.
Profile type (UR S10 Table 1)\(K_2\) ahead\(K_2\) astern
NACA-00 series, Gottingen1.100.80
Flat side1.100.90
Hollow1.350.90
High lift rudders1.701.30
Fish tail1.400.80
Single plate1.001.00
Mixed profiles (e.g. HSVA)1.210.90

The rule takes the ship’s speed, not the propeller slipstream speed, and lets \(K_3\) stand for the rudder’s position in or out of the jet.

Rudder torque and the astern case

The torque is \( Q_R = C_R\,r \), with the lever \( r = c\,(\alpha - k_1) \) (S10.2.1.2). \(c\) is the mean breadth of the rudder area. \(\alpha\) places the center of pressure at 0.33 of the breadth from the leading edge going ahead and 0.66 going astern. \(k_1\) is the balance ratio, the area forward of the stock centerline divided by the rudder area. Going ahead, the lever is not taken as less than 0.1c. A semi-spade rudder is split at the horn into two areas, each with its own breadth and balance, and the two torques are added (S10.2.2).

Astern speeds are lower and \(K_2\) astern is smaller, but the astern lever is far longer. Which case sizes the stock depends on the balance and on the ship’s maximum astern speed, so both are run.

Worked example: a 40 m2 spade rudder

Take a spade rudder with no horn: blade area 40 m2, mean height 8 m, NACA-00 profile, behind a single open propeller, on a ship with a maximum service speed of 15 knots. Then \( \lambda = 8^2/40 = 1.6 \), so \( K_1 = 1.2 \); the mean breadth is 5 m; \( K_2 = 1.10 \) ahead and 0.80 astern; \( K_3 = 1.0 \).

CaseSpeed\(C_R\)Lever \(r\) at \(k_1 = 0.2\)\(Q_R\)
Ahead15 kn1.568 MN5(0.33 - 0.2) = 0.65 m1.019 MN m
Astern at 0.5 V7.5 kn0.285 MN5(0.66 - 0.2) = 2.30 m0.656 MN m
Astern at 0.7 V10.5 kn0.559 MN2.30 m1.285 MN m

At the rule minimum astern speed of 0.5 V, ahead governs. If the ship’s maximum astern speed is 0.7 V, the astern torque is about 26% higher than the ahead torque and the stock is sized astern. Raising the balance to \(k_1 = 0.3\) brings the ahead lever down to the 0.1c floor of 0.5 m, cutting the ahead torque to 0.784 MN m, while the astern torque at 0.7 V falls only to 1.006 MN m.

Rudder stock, couplings and blade structure

The rudder stock carries the torque from the steering gear to the blade and, on a spade or semi-spade rudder, a share of the bending from the rudder force. UR S10 sizes it first for torque, then increases it where bending is present.

Stock diameter in torsion and in combined loading

For torque alone, S10.4.1 gives

$$ d_t = 4.2\,(Q_R\,k)^{1/3} $$

with \(d_t\) in mm, \(Q_R\) in N m and \(k\) the material factor. That corresponds to a torsional stress of 68/k N/mm2. For the worked example above, an ahead torque of 1.019 MN m at \(k = 1\) gives \( d_t = 423 \) mm; a torque of 3 MN m gives about 606 mm.

Where the stock also carries a bending moment \(M\), S10.4.2 limits the equivalent stress \( \sigma_c = \sqrt{\sigma_b^2 + 3\tau_t^2} \) to 118/k N/mm2, which gives the increased diameter

$$ d_c = d_t \left(1 + \tfrac{4}{3}\left(\tfrac{M}{Q_R}\right)^2\right)^{1/6} $$

A bending moment of half the torque raises the example stock from 423 mm to 443 mm, and sizing it on the 0.7 V astern torque of 1.285 MN m instead gives about 457 mm before any bending. On a spade rudder, where the stock carries all the bending, the combined check is the one that sizes it. Where a steel with yield stress above 235 N/mm2 is used to reduce the diameter, S10.4.3 lets the society ask for a check of stock deformation, so that the smaller stock does not bend enough to load the bearing edges.

Material factor

UR S10 is written for a reference steel of 235 N/mm2 yield. It corrects other steels with \( k = (235/R_{eH})^e \), where \(e = 0.75\) for \(R_{eH}\) above 235 N/mm2 and 1.00 at or below it, and \(R_{eH}\) is not taken as more than 0.7 times the tensile strength or 450 N/mm2 (1.3.5). Stocks, pintles, keys and bolts need a minimum yield stress of at least 200 N/mm2. Stocks are forged, rolled or cast carbon-manganese steel to the IACS material requirements, and the forgings and castings are tested and certified by the society.

Couplings

The stock joins the blade by a horizontal flange, a vertical flange or a cone. A cone coupling with a key and no hydraulic arrangement has a taper of 1:8 to 1:12 on the diameter, a secured slugging nut and a coupling length generally not less than 1.5 times the stock diameter at the top of the cone (S10.6.3.1). For stocks above 200 mm, S10.6.4.1 recommends a hydraulic press fit with a taper of about 1:12 to 1:20, with the push-up pressure and length calculated under 6.4.2 and 6.4.3. “Recommends” is the rule’s own word: the hydraulic fit is not mandatory. More on the stock and couplings is in rudder stock and coupling.

Rudder blade plating and slot welds

The blade is a closed box of side plating on internal horizontal and vertical webs. UR S10 S10.5.1 limits the blade’s general bending stress to 110/k N/mm2, shear to 50/k N/mm2 and equivalent stress to 120/k N/mm2. Because the side plating can only be welded to the internal webs from outside once the box is closed, the last plate is attached by slot welds. S10.1.4.1 restricts them: slots at least 75 mm long and twice the plate thickness wide, ends not more than 125 mm apart, and the slots filled, for example with epoxy putty, not with weld metal.

Pintles, bearings, carrier and trunk seals

A rudder is held in line by a set of journal bearings along the stock axis and carried vertically by a rudder carrier at the stock head. UR S10 sizes each of them, and UR Z3 has their clearances recorded at every bottom survey. The rudder bearings and pintles article treats them in more detail.

Pintles

A pintle is a pin on the rudder axis that turns in a bearing, the gudgeon, in the horn or sole piece. UR S10 S10.7.1 sizes it as \( d_p = 0.35\sqrt{B\,k_p} \) mm, where \(B\) is the bearing force in newtons. A bearing force of 600 kN with \(k_p = 1\) gives a pintle of 271 mm. The taper is 1:8 to 1:12 for a keyed pintle with a slugging nut and 1:12 to 1:20 for a pintle mounted by oil injection with a hydraulic nut (7.2.1). The pintle housing is to be at least as long as the pintle diameter and at least a quarter of it thick (7.4).

The pintle nut and its locking are the details that failed on the Achilles Bulker in 2023, which the section on rudder casualties below sets out.

Bearing materials and surface pressure

The bearing area is sized from the bearing force and an allowable surface pressure: \( A_b = P/q_a \), with \(A_b\) the projected area, the length times the outer diameter of the liner (S10.8.2).

Bearing material (UR S10 Table 3)Allowable surface pressure \(q_a\), N/mm2
Lignum vitae2.5
White metal, oil lubricated4.5
Synthetic material, hardness over 60 Shore D5.5 (up to 10 on the maker’s test evidence)
Steel, bronze and hot-pressed bronze-graphite7.0

The length to diameter ratio of a bearing is not to exceed 1.2, and a pintle bearing’s length lies between one and 1.2 times the pintle diameter (S10.8.3). Liners and bushes are at least 8 mm thick for metal and synthetic material and 22 mm for lignum vitae (S10.8.1.1). For the 600 kN example, a synthetic bearing at 5.5 N/mm2 needs about 109,000 mm2 of projected area, a diameter of about 302 mm at a length of 1.2 diameters.

Bearing clearances

UR S10 S10.8.4 sets the as-fitted clearance, on the diameter. For metal bearings it “should not be less than” \( d_b/1000 + 1.0 \) mm, where \(d_b\) is the inner diameter of the bush: 1.3 mm for a 300 mm bush. For non-metallic bearings the clearance is set from the material’s swelling and thermal expansion and “is not to be taken less than 1.5 mm” unless the manufacturer recommends a smaller value and there is documented evidence of satisfactory service. The metal rule is written as a recommendation and the non-metallic one as a requirement.

These are minimum fitted clearances. Neither UR S10 nor UR Z3 sets a maximum wear-down clearance; that figure comes from the bearing maker or the individual society’s rules.

Rudder carrier and anti-lifting

The weight of the rudder is supported by a carrier bearing, for example a rudder carrier attached to the upper part of the stock (UR S10 1.2.1), and “suitable arrangements are to be provided to prevent the rudder from lifting” (1.2.2). The rule gives no figure for the jumping clearance between the rudder and its anti-lifting stop; that is set by the society and the yard. Carrier arrangements are described under rudder carrier bearing.

Trunk seals

Where the rudder trunk is open to the sea, Rev.8 clause 1.2.3 requires a seal or stuffing box above the waterline at scantling draught without trim, to keep water out of the steering gear compartment and keep the carrier’s lubricant from being washed away. If the top of the trunk is below that waterline, two separate watertight seals or stuffing boxes are required. More on the trunk is in rudder trunk and seals.

IMO maneuvering standards: MSC.137(76)

MSC.137(76), the Standards for Ship Manoeuvrability, sets four groups of criteria a ship should meet: turning ability, initial turning ability, yaw-checking and course-keeping, and stopping. It was adopted by the Maritime Safety Committee on 4 December 2002 and superseded the Interim Standards of A.751(18) of November 1993. The resolution is also described under ship maneuverability standards.

Status and application

MSC.137(76) is a recommendation. Its operative paragraph invites Governments to encourage those who design, build, repair and operate ships to apply the Standards to ships constructed on or after 1 January 2004. It has no entry into force and is not part of SOLAS. A flag Administration, a classification society or a shipbuilding contract can make it a condition, but “mandatory” is wrong as a description of the resolution itself.

Paragraph 3.1 applies the Standards to ships “of all rudder and propulsion types, of 100 m in length and over, and chemical tankers and gas carriers regardless of the length”. A ship that is repaired or modified in a way that may affect its maneuvering is to be checked for continued compliance (3.2), and other ships modified to the extent of a new ship should comply (3.3). High-speed craft are excluded (3.4). The Standards were written for ships with traditional propulsion and steering, shaft-driven with conventional rudders (1.2), but 3.1 covers all types.

Compliance can be shown at the design stage by scale model tests or computer prediction, with full-scale trials to validate them (2.1.1). A ship that met the Standards on prediction is considered to meet them regardless of the trial results unless the Administration finds the prediction work substandard or the ship’s performance in substantial disagreement. The alternative is full-scale trials alone (2.1.2).

Test conditions

The test speed is at least 90% of the ship’s speed corresponding to 85% of maximum engine output (4.2.1). The Standards apply in deep, unrestricted water, in a calm environment, at full load, meaning summer load line draught, on an even keel, after a steady approach at the test speed (5.2). The Explanatory Notes in MSC/Circ.1053 of 16 December 2002, which govern how maneuvering trials are run, take deep water as more than four times the mean draught, with wind not above Beaufort 5 and waves not above sea state 4. Trials run in another condition are corrected to the standard condition by the methods in the Explanatory Notes (6.1).

Ship length \(L\) throughout is the length between perpendiculars (4.1.1), and the zigzag limits use \(L/V\) in seconds, with \(L\) in meters and \(V\) in meters per second. The trials themselves are described in sea trials and performance testing.

Turning ability

Turns are made to both sides at 35 degrees of rudder, or the maximum rudder angle permissible at the test speed. In them the advance is not to exceed 4.5 ship lengths and the tactical diameter 5 ship lengths (5.3.1). Advance is the distance traveled by the midship point in the direction of the original course from the rudder order until the heading has changed 90 degrees. Tactical diameter is the distance traveled by the midship point from the rudder order until the heading has changed 180 degrees, measured perpendicular to the original heading (4.2.3, 4.2.4).

Formula

Advance and Tactical Diameter

$$\text{Advance} \leq 4.5 L, \quad \text{Tactical diameter} \leq 5 L$$

where

\(L\)Length between perpendicularsm
\(Advance\)Distance traveled by the midship point in the direction of the original course, from the rudder order to 90 degrees heading change (4.2.3)m
\(Tactical diameter\)Distance traveled by the midship point from the rudder order to 180 degrees heading change, measured perpendicular to the original heading (4.2.4)m

Source: IMO Resolution MSC.137(76), 4 December 2002, paragraph 5.3.1 (35 degrees rudder or maximum permissible at test speed)

Initial turning ability tests the response to a moderate helm order. With 10 degrees of rudder to either side, the ship is not to travel more than 2.5 ship lengths by the time the heading has changed 10 degrees from the original heading (5.3.2).

IMO Resolution MSC.137(76), 4 December 2002, paragraph 5.3.2

IMO MSC.137

$$d_{10^\circ} \leq 2.5\,L$$

where

\(d_{10^\circ}\)Distance traveled by the time the heading has changed 10 degrees, with 10 degrees of rudderm
\(L\)Length between perpendicularsm

Yaw-checking and course-keeping

The zigzag test measures how quickly the ship answers counter-rudder and how far it swings past the ordered heading. In the 10/10 test, 10 degrees of rudder is applied; when the heading has changed 10 degrees the rudder is reversed to 10 degrees the other way, and so on. The overshoot is the additional heading change after each reversal.

Formula

Zigzag Overshoot Limits

$$\alpha_1 \leq \begin{cases} 10^\circ & L/V < 10\ \text{s} \\ (5 + 0.5\,L/V)^\circ & 10 \leq L/V < 30 \\ 20^\circ & L/V \geq 30 \end{cases}, \quad \alpha_2 \leq \begin{cases} 25^\circ & L/V < 10 \\ (17.5 + 0.75\,L/V)^\circ & 10 \leq L/V < 30 \\ 40^\circ & L/V \geq 30 \end{cases}, \quad \alpha_{1,20/20} \leq 25^\circ$$

where

\(L\)Length between perpendicularsm
\(V\)Test speed, at least 90% of the speed at 85% of maximum engine output (MSC.137(76) 4.2.1)m/s
\(\alpha_1\)First overshoot angle, 10/10 zigzagdeg
\(\alpha_2\)Second overshoot angle, 10/10 zigzagdeg
\(\alpha_{1,20/20}\)First overshoot angle, 20/20 zigzagdeg

Source: IMO Resolution MSC.137(76), 4 December 2002, paragraphs 5.3.3.1 to 5.3.3.3

The first overshoot in the 10/10 test is not to exceed 10 degrees where \(L/V\) is less than 10 s, 20 degrees where it is 30 s or more, and \( 5 + 0.5\,L/V \) degrees in between (5.3.3.1). The second overshoot limits are 25 degrees, 40 degrees and \( 17.5 + 0.75\,L/V \) degrees over the same bands (5.3.3.2). The 20/20 test has one limit: a first overshoot of not more than 25 degrees (5.3.3.3). Where the standard maneuvers point to dynamic instability, the Explanatory Notes describe alternative tests, the spiral and pull-out tests (6.2).

The \(L/V\) form means a longer or slower ship is allowed a larger overshoot, because it takes longer, in seconds, to cover its own length. A short, fast ship has to check its swing quickly.

Stopping ability

In a full astern stopping test, the track reach, the distance along the path of the midship point from the full astern order until the ship is stopped in the water, is not to exceed 15 ship lengths (5.3.4). The Administration may raise this where ships of large displacement make it impracticable, to no more than 20 ship lengths. MSC/Circ.1053 Appendix 3 says that relaxation is only likely to be needed for large tankers, and its worked example of a large ship reaches 15.5 lengths. The rudder plays no part in this criterion beyond holding the ship on a course while the propeller stops it.

Worked check for a 200 m ship

Take a ship of 200 m between perpendiculars with a test speed of 15 knots, 7.72 m/s. Then \( L/V = 25.9 \) s, inside the middle band.

Criterion (MSC.137(76))LimitFor L = 200 m, V = 15 kn
Advance (5.3.1)4.5 L900 m
Tactical diameter (5.3.1)5 L1,000 m
Initial turning, 10 degrees (5.3.2)2.5 L500 m
10/10 first overshoot (5.3.3.1)5 + 0.5 L/V18.0 degrees
10/10 second overshoot (5.3.3.2)17.5 + 0.75 L/V36.9 degrees
20/20 first overshoot (5.3.3.3)25 degrees25 degrees
Track reach (5.3.4)15 L3,000 m (up to 4,000 m with the Administration’s relaxation)

Maneuvering information on board: A.601(15)

IMO resolution A.601(15), adopted by the Assembly on 19 November 1987, recommends that Administrations require three documents of maneuvering information on board: the pilot card, the wheelhouse poster and the manoeuvring booklet. It superseded the recommendation on manoeuvring booklets in A.209(VII). Like MSC.137(76), it is a recommendation.

Under paragraph 2.1, all new ships to which SOLAS applies should carry a pilot card. All new ships of 100 m in length and over, and all new chemical tankers and gas carriers regardless of size, should carry all three documents. The pilot card is filled in by the master and describes the ship’s current condition: its loading, propulsion and maneuvering equipment (3.1). The documents are to be amended after any modification or conversion that may alter the maneuvering characteristics or extreme dimensions (2.3). The pilot card is what passes to the pilot at the master-pilot exchange during pilotage. The three documents are described under maneuvering information.

The manoeuvring booklet is an A.601(15) document. Neither MSC.137(76) nor SOLAS Chapter V requires it.

Steering without a rudder: azimuth thrusters, pods, waterjets and cycloidal propellers

SOLAS II-1/29 was written around a rudder moved by steering gear. IMO MSC.1/Circ.1416/Rev.1 of 26 June 2019, approved at MSC 101 and to be used from 1 January 2020, interprets it for azimuth thrusters, podded propulsors, waterjets and cycloidal propellers such as the Voith Schneider propeller. It replaced MSC.1/Circ.1416 of 2012.

The interpretation replaces the rudder angle with the unit’s declared steering angle limits, the maker’s operational limits for safe operation at the given speed and propeller torque. The main steering gear must turn the unit from one side to the other at those limits at an average of not less than 2.3 degrees per second at maximum ahead service speed. That matches the 65 degrees in 28 seconds of a rudder ship. The auxiliary gear must achieve 0.5 degrees per second at half the maximum ahead service speed or 7 knots, whichever is greater, which is the rudder ship’s 30 degrees in 60 seconds. The auxiliary gear must be power-operated in any ship with more than 2,500 kW of propulsion power per steering-propulsion unit.

A ship with several steering-propulsion units has, on each, either a main and an auxiliary steering gear or two or more identical steering actuating systems. A ship with a single unit needs two or more actuating systems and a detailed risk assessment showing that steering is kept after any single failure in the gear, the control system or the power supply. Maneuverability tests such as those in MSC.137(76) are run with steering angles within the declared limits. Steering by thrust also means a ship can lose steering when it loses propulsion, where a rudder ship keeps some steerage way while its headway lasts, and 29.14 in the interpretation applies only to units with proven steering capability from ship speed after propulsion has failed.

Propeller-rudder interaction and restricted water

A rudder behind a propeller sits in the slipstream, which runs faster than the ship through the water whenever the propeller is producing thrust. That is why a short, hard burst of ahead power with the rudder over turns a slow or stopped ship: the rudder force follows the slipstream speed, not the ship’s speed. UR S10 reflects the position effect only through \(K_3\), and the design force uses the ship’s speed.

The interaction runs both ways. The rudder blocks part of the slipstream and adds to the hull’s resistance, and the rotating slipstream meets the two halves of the rudder at different angles, which is the effect twisted rudders are shaped for. Going astern, the propeller’s flow no longer reaches the rudder face, and astern steering is weak in most single-screw ships. Marine propeller design, propeller theory and propeller-rudder interaction cover the propeller side. Propeller cavitation reaches the rudder in the slipstream, and Becker cites reduced cavitation as one aim of its twisted rudder.

Shallow water changes the hull forces the rudder is working against. The MSC.137(76) criteria apply in deep, unrestricted water, and a ship that meets them can turn on a far larger circle in a channel. Squat, bank effect and the ship’s under-keel clearance govern the margin in a channel.

Rudder survey and inspection

The rudder is surveyed at each examination of the outside of the ship’s bottom. IACS UR Z3 Rev.8, implemented from 1 July 2020, requires at least two such examinations in each five-year special survey period, one of them at the special survey, with no more than 36 months between any two. The requirement as a whole is described under UR Z3 bottom survey.

UR Z3.2.4 sets the rudder content of each examination:

“Visible parts of rudder, rudder pintles, rudder shafts and couplings and stern frame are to be examined. If considered necessary by the Surveyor, the rudder is to be lifted or the inspection plates removed for the examination of pintles. The clearance in the rudder bearings is to be ascertained and recorded. Where applicable, pressure test of the rudder may be required as deemed necessary by the Surveyor.”

(IACS UR Z3 Rev.8, 2019, clause Z3.2.4; the published text’s missing articles are restored.)

The clearances recorded at each docking form a wear trend, read against the maker’s or the society’s maximum, since UR Z3 sets none. Where one of the bottom examinations is done as an in-water survey in lieu of drydocking, the proposal for it is to give special consideration to ascertaining the rudder bearing clearances. Thickness gauging, crack detection by non-destructive testing and inspection of the cathodic protection on the blade follow the society’s survey procedures.

Rudder casualties

Two cases with official findings mark the boundary drawn at the top of this article: one failure of the rudder itself, and one of the steering gear that moves it.

Achilles Bulker, 2023: loss of a rudder pintle

On 24 July 2023 the Panama-flagged bulk carrier Achilles Bulker suffered damage to its rudder off the Port of Tauranga, New Zealand. New Zealand’s Transport Accident Investigation Commission investigated as inquiry MO-2023-205 and published its report on 24 July 2025. It found that “the pintle nut unwound off the top of the pintle, allowing the pintle to drop out from the bottom of the rudder”. The welds securing the locking piece and the pintle stopper to the pintle nut had fractured and were of “generally poor quality with limited weld penetration”. Without the pintle, fatigue cracks grew, and “because of overload, the fatigued palm fractured on both sides of the rudder stock”.

TAIC issued two recommendations on 26 June 2025. Recommendation 043/25 asked the builder, Shanhaiguan Shipbuilding Industry Co Ltd, to improve quality assurance for pintle assemblies. Recommendation 044/25 asked Maritime New Zealand to promote at IMO standards that ensure sufficient quality assurance for rudder systems; Maritime New Zealand partially accepted it on 17 July 2025. The case bears directly on UR S10’s pintle taper, nut and housing rules and on the anti-lifting rule in 1.2.2. The casualty is also described under Achilles Bulker.

Amoco Cadiz, 1978: steering gear failure

The Amoco Cadiz grounded on the Portsall Rocks off Brittany on 16 March 1978 after a failure of its steering gear, and its entire crude oil cargo was spilled. The rudder was not the part that failed. The case led to the steering gear provisions of the 1981 SOLAS amendments in MSC.1(XLV), in force 1 September 1984, which the marine steering gear article sets out, and its oil pollution history sits with other marine casualty investigations.

Limitations

The UR S10 rudder force is a rule load for sizing structure. It assumes the ship’s service speed with a location factor, not the real slipstream, and it does not predict the force a rudder develops behind a particular propeller and hull. Rudders outside the ordinary and enhanced profiles UR S10 covers, very large rudders and unusual arrangements are assessed by direct analysis under clause 1.5, and the society’s own rules may add to UR S10. The worked examples above use round numbers to show how the clauses behave; they are not a design.

The figures here are the IACS unified requirement, which each member society writes into its own rules, sometimes with additions. A ship is built to its society’s rules in the edition fixed by its contract date, and where a society’s rule differs from UR S10 the society’s rule governs for that ship. Wear-down limits for bearings, jumping clearances and rudder drop limits come from the society and the maker, not from UR S10 or UR Z3, and vary between them.

MSC.137(76) and A.601(15) are recommendations, and a ship’s obligation to meet them comes from its flag Administration, its class or its building contract. The criteria apply in deep, unrestricted, calm water at full load; they say nothing about a ship’s behavior in a channel, in wind, or at slow speed. Manufacturer figures for flap, Schilling and twisted rudders are stated by the maker and are attributed as such. They are not measured results for any particular ship.

Frequently Asked Questions (FAQs)

What is the IACS formula for rudder force?

IACS UR S10 gives the design rudder force as C_R = 132 K1 K2 K3 A V^2 newtons (S10.2.1.1).

A is the rudder blade area in square meters and V is the maximum service speed in knots on the summer load waterline, with (V + 20)/3 used below 10 knots. K1 = (lambda + 2)/3 is the aspect ratio factor with lambda not more than 2, K2 is the profile factor from Table 1 (1.10 ahead and 0.80 astern for a NACA-00 or Gottingen profile), and K3 is 0.8 outside the propeller jet, 1.15 behind a fixed propeller nozzle and 1.0 otherwise.

Which revision of IACS UR S10 applies to a new ship?

It depends on the date of the contract for construction.

Rev.7 (February 2023, with Corrigendum 1 of June 2023 and Corrigendum 2 of May 2024) applies to ships contracted on or after 1 July 2024. Rev.8, dated 4 September 2025, applies to ships contracted on or after 1 January 2027. A ship contracted between those dates is built to Rev.7.

What did UR S10 Rev.8 change?

Rev.8 clarified two things: the waterline used to position the seal or stuffing box in an open rudder trunk (clause 1.2.3, now the waterline at scantling draught without trim) and the description of the rudder horn section areas used in the horn strength check (clause 9.2.1 and Annex S10.5).

The rudder force and torque formulas, the K factors, the stock diameter formula, the bearing pressure table, the clearances and the coupling tapers are unchanged from Rev.7.

What profile factor K2 does a high-lift or fishtail rudder use?

UR S10 Table 1 gives K2 = 1.70 ahead and 1.30 astern for high-lift rudders, and 1.40 ahead and 0.80 astern for a fish tail profile.

The other rows are NACA-00 or Gottingen 1.10 and 0.80, flat side 1.10 and 0.90, hollow 1.35 and 0.90, single plate 1.00 and 1.00, and mixed profiles such as HSVA 1.21 and 0.90.

Can the astern condition govern rudder torque?

Yes. UR S10 places the center of pressure at 0.33 of the mean breadth from the leading edge ahead and at 0.66 astern, so the astern lever c(0.66 - k1) is several times the ahead lever.

With a balance of 0.2 and an astern speed of 0.7 V, a 40 m2 spade rudder at 15 knots carries about 1.29 MN m astern against about 1.02 MN m ahead, so astern sets the stock size. At the minimum astern speed of 0.5 V the ahead case governs the same rudder.

How is the rudder stock diameter calculated?

UR S10 S10.4.1 sizes the stock for torque alone as d_t = 4.2 (Q_R k)^(1/3) millimeters, with Q_R in newton meters and k the material factor, which corresponds to a torsional stress of 68/k N/mm2.

Where the stock also carries bending, S10.4.2 increases it to d_c = d_t (1 + (4/3)(M/Q_R)^2)^(1/6) so that the equivalent stress does not exceed 118/k N/mm2.

What is the material factor k in UR S10?

k = (235/ReH)^e, where ReH is the minimum yield stress in N/mm2, e = 0.75 for ReH above 235 and 1.00 for ReH of 235 or less, and ReH is not taken as more than 0.7 times the tensile strength or 450 N/mm2 (UR S10 1.3.5).

Stocks, pintles, keys and bolts need a minimum yield stress of at least 200 N/mm2. A steel with ReH of 235 N/mm2 has k = 1.0.

What surface pressures are allowed on rudder bearings?

UR S10 S10.8.2 Table 3 allows 2.5 N/mm2 for lignum vitae, 4.5 N/mm2 for oil-lubricated white metal, 5.5 N/mm2 for synthetic material harder than 60 Shore D, and 7.0 N/mm2 for steel, bronze and hot-pressed bronze-graphite.

A synthetic bearing may go higher on the maker’s test evidence, but never above 10 N/mm2. The bearing length to diameter ratio is not to exceed 1.2.

What is the minimum clearance for a rudder bearing?

For metal bearings UR S10 S10.8.4 says the clearance should not be less than db/1000 + 1.0 mm on the diameter, where db is the inner diameter of the bush.

For non-metallic bearings the clearance is set from the material’s swelling and thermal expansion and is not to be less than 1.5 mm unless the manufacturer recommends less and there is documented satisfactory service history.

Does IACS set a maximum wear-down clearance for rudder bearings?

No. The UR S10 clearances are minimum as-fitted values, not wear limits.

UR Z3.2.4 requires the clearance in the rudder bearings to be ascertained and recorded at each bottom examination but sets no figure. The maximum in-service clearance comes from the bearing maker or the individual classification society’s rules.

How often are rudder bearing clearances measured?

At every examination of the outside of the ship’s bottom under IACS UR Z3 Rev.8, which requires at least two examinations in each five-year special survey period, one of them at the special survey, with no more than 36 months between any two.

An in-water survey in lieu of drydocking proposal must give special consideration to how the bearing clearances will be found.

Is a rudder pressure-tested at drydocking?

Only where applicable and where the surveyor considers it necessary.

UR Z3.2.4 says a pressure test of the rudder may be required as deemed necessary by the surveyor, and the rudder is to be lifted or inspection plates removed to examine the pintles if the surveyor considers it necessary.

When does a rudder trunk need two seals?

Under UR S10 Rev.8 clause 1.2.3, a rudder trunk open to the sea carries a seal or stuffing box above the waterline at scantling draught without trim.

If the top of the trunk is below that waterline, two separate watertight seals or stuffing boxes are required.

Is IMO resolution MSC.137(76) mandatory?

No. MSC.137(76), the Standards for Ship Manoeuvrability adopted on 4 December 2002, is a recommendation.

It invites Governments to encourage designers, builders, repairers and operators to apply the Standards to ships constructed on or after 1 January 2004. It has no entry-into-force date. A flag Administration or a classification society can make it a condition, but SOLAS does not.

Which ships do the IMO maneuverability standards cover?

MSC.137(76) paragraph 3.1 applies to ships of all rudder and propulsion types of 100 m in length and over, and to chemical tankers and gas carriers regardless of length.

Paragraph 3.4 excludes high-speed craft. A ship repaired or modified in a way that may affect its maneuvering should still comply, and a ship modified to the extent of a new ship should comply.

What are the IMO turning circle limits?

MSC.137(76) 5.3.1 limits the advance to 4.5 ship lengths and the tactical diameter to 5 ship lengths in a turn with 35 degrees of rudder, or the maximum rudder angle permissible at the test speed.

Ship length here is the length between perpendiculars.

What are the IMO zigzag overshoot limits?

For the 10/10 zigzag, the first overshoot must not exceed 10 degrees where L/V is under 10 s, 20 degrees where L/V is 30 s or more, and (5 + 0.5 L/V) degrees in between.

The second overshoot limits are 25 degrees, 40 degrees and (17.5 + 0.75 L/V) degrees for the same bands. The 20/20 zigzag has one limit: a first overshoot of 25 degrees. L is in meters and V in meters per second.

What is the IMO stopping distance limit?

MSC.137(76) 5.3.4 limits the track reach in a full astern stopping test to 15 ship lengths.

The Administration may raise this for ships of large displacement where 15 lengths is impracticable, with 20 ship lengths as the ceiling. MSC/Circ.1053 Appendix 3 says the relaxation is only likely to be needed for large tankers.

At what speed and loading are IMO maneuvering trials run?

The test speed is at least 90% of the ship’s speed at 85% of maximum engine output (MSC.137(76) 4.2.1).

The standards apply in deep, unrestricted water, in a calm environment, at full load (summer load line draught) on an even keel, after a steady approach (5.2). MSC/Circ.1053 takes deep water as more than four times the mean draught, wind not above Beaufort 5 and waves not above sea state 4.

Can a ship show compliance with MSC.137(76) from a ballast trial?

Yes. Where trials cannot be run at full load, MSC.137(76) 6.1 has the results corrected to the standard condition using the methods in the Explanatory Notes, MSC/Circ.1053.

The standards also allow compliance to be shown at the design stage by scale model tests or computer prediction, validated by full-scale trials.

What is the difference between MSC.137(76) and A.601(15)?

MSC.137(76) sets performance criteria a ship should meet: turning, initial turning, yaw-checking and stopping.

A.601(15), adopted on 19 November 1987, sets how maneuvering information is provided and displayed on board: the pilot card, the wheelhouse poster and the manoeuvring booklet. Both are recommendations.

Which ships carry a pilot card and wheelhouse poster?

Under A.601(15) paragraph 2.1, all new ships to which SOLAS applies should carry a pilot card.

All new ships of 100 m in length and over, and all new chemical tankers and gas carriers regardless of size, should carry the pilot card, the wheelhouse poster and the manoeuvring booklet. The documents are to be amended after a modification or conversion that may alter the ship’s maneuvering characteristics or extreme dimensions.

How do ships with azimuth thrusters or pods meet the steering rate requirement?

IMO MSC.1/Circ.1416/Rev.1 of 26 June 2019 interprets SOLAS II-1/29 for azimuth thrusters, podded propulsors, waterjets and cycloidal propellers.

The main steering gear must turn the unit from one side to the other at its declared steering angle limits at an average of not less than 2.3 degrees per second at maximum ahead service speed. The auxiliary gear must achieve 0.5 degrees per second at half that speed or 7 knots, whichever is greater.

Do the IMO manoeuvring trials apply to podded and azimuth thruster ships?

Yes. MSC.137(76) applies to ships of all rudder and propulsion types.

MSC.1/Circ.1416/Rev.1 adds that maneuverability tests such as those in MSC.137(76) are carried out with steering angles not exceeding the unit’s declared steering angle limits.

How far can a Schilling rudder turn?

Becker Marine Systems states that its Schilling rudder, a one-piece high-lift rudder with a fishtail trailing edge and no moving parts, operates at rudder angles of up to 70 degrees to either side, against 35 degrees for a conventional semi-spade rudder.

UR S10 Table 1 lists a fish tail profile at K2 = 1.40 ahead and 0.80 astern, and the classification society decides which row a given rudder takes.

Is the Becker Twisted Fin a type of rudder?

No. Becker describes the Twisted Fin as a pre-swirl device installed in front of the propeller, with a power saving of up to 4% stated by the maker.

It can be combined with the Becker Twist Rudder, which is a separate rudder product with a twisted leading edge.

What happened to the rudder of the Achilles Bulker?

On 24 July 2023 off the Port of Tauranga, New Zealand, the pintle nut on the Panama-flagged bulk carrier Achilles Bulker unwound off the top of the pintle and the pintle dropped out of the bottom of the rudder.

New Zealand’s Transport Accident Investigation Commission (inquiry MO-2023-205, report published 24 July 2025) found the welds securing the locking piece and pintle stopper were of poor quality with limited penetration, and that the fatigued rudder palm then fractured from overload.

What pintle taper does UR S10 require?

UR S10 S10.7.2.1 requires a taper of 1:8 to 1:12 on the diameter for a keyed pintle secured by a slugging nut, and 1:12 to 1:20 for a pintle mounted with oil injection and a hydraulic nut.

The pintle housing length is not to be less than the pintle diameter, and its thickness not less than 0.25 times the pintle diameter.

What is the difference between a spade rudder and a semi-spade rudder?

A spade rudder hangs from its stock with no support below the hull, so the stock and its bearings carry the full bending moment.

A semi-spade rudder turns about the same stock axis but is supported part-way down by a pintle in a fixed rudder horn, which UR S10 Annexes S10.5 and S10.6 model as an elastic support. The horn takes part of the bending load and has its own strength check under UR S10 section 9.

Does SOLAS limit the rudder to 35 degrees?

No. SOLAS II-1/29.3.2 sets a test rather than a maximum rudder angle: the main steering gear must put the rudder from 35 degrees on one side to 35 degrees on the other, and from 35 degrees on either side to 30 degrees on the other in not more than 28 seconds.

MSC.137(76) turning tests use 35 degrees or the maximum rudder angle permissible at the test speed, and high-lift rudders are designed for larger angles.

Does the UR S10 rudder force formula use propeller slipstream velocity?

No. UR S10 uses the ship’s maximum service speed V and accounts for rudder position through the location factor K3 (0.8 outside the propeller jet, 1.15 behind a fixed nozzle, 1.0 otherwise).

It is a rule load for scantlings. Clause 1.5 lets a classification society accept direct analysis as an equivalent, which is where slipstream modeling comes in.

Which UR S10 profile factor does a flap rudder take?

UR S10 does not name flap rudders.

Clause 1.1.1 extends the requirement to some enhanced profile rudders with special arrangements for increasing the rudder force, and the classification society decides whether a particular flap rudder falls within it and which Table 1 row applies. Table 1 lists high lift rudders at K2 = 1.70 ahead and 1.30 astern.

How thick must a rudder pintle bush be?

UR S10 S10.8.1.2 gives the pintle bush thickness as t = 0.01 sqrt(B) mm, where B is the bearing force in newtons.

Liners and bushes in way of bearings are at least 8 mm thick for metallic and synthetic material and 22 mm for lignum vitae (S10.8.1.1).

What limits does UR S10 put on slot welds in the rudder blade?

UR S10 S10.1.4.1 restricts slot welding: slots are at least 75 mm long and twice the plate thickness wide, their ends are not more than 125 mm apart, and they are filled, for example with epoxy putty, not with weld metal.

In way of the horn recess of a semi-spade rudder, the radii are to be at least five times the plate thickness and not less than 100 mm (S10.1.4.2).

Sources

  1. IACS UR S10 (Rev.8, September 2025). Rudders, Sole Pieces and Rudder Horns classnk.com
  2. IMO Resolution MSC.137(76), 4 December 2002. Standards for Ship Manoeuvrability imo.org
  3. IMO MSC/Circ.1053, 16 December 2002. Explanatory Notes to the Standards for Ship Manoeuvrability register-iri.com
  4. IMO Resolution A.601(15), 19 November 1987. Provision and Display of Manoeuvring Information on board Ships imo.org
  5. IMO MSC.1/Circ.1416/Rev.1, 26 June 2019. Unified Interpretations of SOLAS Regulations II-1/28, II-1/29 and II-1/30 deutsche-flagge.de
  6. IACS UR Z3 (Rev.8, 2019). Periodical Survey of the Outside of the Ship's Bottom and Related Items iacs.s3.af-south-1.amazonaws.com
  7. TAIC inquiry MO-2023-205. Achilles Bulker, loss of rudder pintle, Tauranga, 24 July 2023 taic.org.nz